쉐도잉 연습: Repairing Big Dents with Body Filler: Full Auto Body Tutorial - 영상으로 영어 말하기 배우기

Hey guys, today I'm going to be sharing my tips

and tricks on how to repair big dents like this so

that you can be more confident with your bodywork or side projects.

The first thing I always do when repairing damage is getting the overall shape of the panel back to normal.

I'll start by knocking out the wheelhouse edge with a slide hammer.

Then I'll knock down any crowns or high spots.

Now to tackle the main damage.

If you take a good look at the damage, it may look like a crease, but around the crease is actually a big dent.

I'll start by using a series of glue tabs along the crease to remove the bulk of the dent.

Using glue is super helpful when removing big dents because it helps move a lot of metal.

I'll use a slide hammer going back and forth working out the dent.

I'll strip the paint down to metal so that I'm able to use a dent puller.

I'll be using the Maxi, but you can also use a Uniswatter with pins.

Before using the dent puller, I like to spray guide coat and sand it down to reveal my highs in low spots.

All the dark spots that were left untouched from sanding are low spots.

These are areas we'll need to work out.

When metalworking a crease, I prefer using a slapping file instead of a body hammer.

It has a wider surface area which helps knock down the high spots while not creating any extra damage.

What I'm doing here is using the rod to hold pressure out on the low spot

while using the slapper to knock around the crease.

This will help flatten it out so

I'll clean up the burn marks from the dent puller with a roll lock wheel, then I'll use 80 grit on a DA center to blend out the paint before applying a coat of body filler.

I'll start the first coat with Rage body filler.

When mixing body filler always use a clean surface.

If you're starting out I recommend using as big as a board as you can get.

It can get quite messy.

The mixture ratio is 50 to 1 body filler to hardener.

I normally just put a bead of hardener about 3 quarters to half way across.

When mixing body filler you don't want to stir it as it will create air pockets in your filler filler.

What you want to do is press it down tightly as you see me doing here.

Continue doing this until it's a uniform color.

When applying body filler for the first layer onto the metal, try to apply it as tight as possible.

You don't want to get it all in one shot, rather applying several thin coats on top as needed.

Thank you.

I'll start sanding the first coat with 80 grit sandpaper.

My goal is to sand for the overall shape of the panel.

Once I have the shape, I'll start working on making sure it's nice and flat.

If you hit any metal spots that stick out, hammer them down before continuing.

Now that I'm happy with the overall shape, it's ready for a coat of metal glaze.

This is also a type of body filler but it's much thinner.

I'll be applying this over the paint.

I always apply this as the final coat to blend out the bodywork

and to fill in any deep scratches from the last coat.

I'll sand this with 180 grit then finish in a 220 grit.

I've also applied a dry guide coat onto the filler to have a visual on my sanding.

You can see how useful the guide coat is here while sanding the body line.

I'm sorry.

With the block sanding done, I'll use a DA sander with 220 grit to remove any block sanding scratches on the paint around the body filler.

Then I'll apply Evercoat's 440 Express to fill in any micro pinholes.

I've installed the bumper and taillights to make sure it still matches up.

I wasn't happy with the body line here

so I've matched the body line on the other side with my tool and drew a line.

Then I'll apply a tape and correct the body line.

With everything corrected, the final thing to do is to double check the bodywork.

I'll spray QuickCheck over the entire area and look through the reflections for any imperfections.

If everything looks good, then you're all done and ready for primer.

But for this video, that's going to be it.

Hope you learned something.

쉐도잉이란? 영어 실력을 빠르게 키우는 과학적 방법

쉐도잉(Shadowing)은 원래 전문 통역사 훈련을 위해 개발된 언어 학습 기법으로, 다언어 학자인 Dr. Alexander Arguelles에 의해 대중화된 방법입니다. 핵심 원리는 간단하지만 매우 강력합니다: 원어민의 영어를 들으면서 1~2초의 짧은 지연으로 즉시 소리 내어 따라 말하는 것——마치 '그림자(shadow)'처럼 화자를 따라가는 것입니다. 문법 공부나 수동적인 청취와 달리, 쉐도잉은 뇌와 입 근육이 동시에 실시간으로 영어를 처리하고 재현하도록 훈련합니다. 연구에 따르면 이 방법은 발음 정확도, 억양, 리듬, 연음, 청취력, 말하기 유창성을 크게 향상시킵니다. IELTS 스피킹 준비와 자연스러운 영어 소통을 원하는 분들에게 특히 효과적입니다.

쉐도잉 연습: Repairing Big Dents with Body Filler: Full Auto Body Tutorial - 영상으로 영어 말하기 배우기

이 레슨에 대해

쉐도잉이란? 영어 실력을 빠르게 키우는 과학적 방법