Shadowing-Übung: Aircraft Gas Turbine Engines #01 - Introduction Part 1 - Englisch Sprechen Lernen mit Video
Übungsmodus wählen
Jeder Modus öffnet einen Übungsraum im Vollbild.
92 Sätze
Wenn Sätze zu kurz oder zu lang sind, klicke auf Edit, um sie anzupassen.
1
Jet propulsion can be defined as the force
2
which is generated in the opposite direction to that of a discharge of fluid under pressure escaping through an opening.
3
The force that makes a lawn sprinkler, similar to the one shown here, rotate when water flows through it is one example of jet propulsion that is readily apparent in everyday life.
4
and the thrust that sends rockets like this one into space is another, which is perhaps not such an everyday occurrence.
5
Whatever the form that the device utilizing jet propulsion takes,
6
it is essentially a reaction engine which operates on the principle of the third law of motion, as stated by the English physicist Sir Isaac Newton in 1687,
7
which is that every reaction has an equal and opposite reaction.
8
The first recorded use of a reaction engine was by Hero of Alexandria in 250 BC.
9
Hero's engine, a representation of which is shown here, consisted of a sphere into which steam was introduced under pressure.
10
The steam was fed through apertures in the centre of the bearings upon which the sphere was allowed to rotate.
11
Allowing the steam to escape through nozzles in two bent tubes
12
mounted opposite one another on the surface of the sphere created thrust, which caused the sphere to rotate around its axis.
13
It's alleged that Hero invented his engine while he was investigating different methods of opening the doors of a temple in Alexandria.
14
In recent times, one of the first attempts at creating jet-powered aircraft resulted in the development of a hybrid design.
15
An Italian, Secondo Campini, designed a system whereby an external power source, in this case a conventional piston engine, powered a compressor.
16
The output of the compressor was mixed with fuel, the mixture of air and fuel ignited, and jet thrust resulted.
17
collaborated with the Italian aircraft manufacturers Caproni, and in August of 1940, the Campini Caproni CC2 flew.
18
Although the Italians were unaware of it, a year earlier than this the Germans had flown their version of a jet aircraft, the Henkel 178.
19
This aircraft was powered by an engine designed by a young German scientist called Hans von Ohain.
20
Despite the relatively sparkling performance for that era it could travel at speeds in excess of 400 miles per hour,
21
the German Air Force initially paid its scant regard and it was never produced in any quantity.
22
On the 8th of April 1941, the first official flight of the Gloucester E-2839 aircraft took place at Brockworth in Gloucestershire.
23
Sir Frank Whittle had submitted patents for his jet engine in 1930, but it was not until 1939 that sufficient financial
24
and technical backing was found to enable him to manufacture a flyable version of his engine.
25
The firm of Rover had, reluctantly, initially been contracted to produce the Whittle engine, but Rolls-Royce, who could see its potential,
26
eventually took over development of the engine, one of which is shown here.
27
Rolls-Royce reworked the Whittle design to produce the Derwent engine, an example of which is depicted here.
28
This engine was capable, in its Mark IV version, of producing 2,450 pounds of thrust.
29
Later versions of the engine, capable of 3,600 pounds of thrust, were used to power the Gloucester Meteor F-8, like the one shown here,
30
flying at an open day at Royal Air Force Kemble in the year 2000.
31
During a visit to the United States in early 1944, the leader of the Rolls-Royce design team found
32
that General Electric were developing engines capable of producing up to 4,000 pounds of thrust.
33
As a response to this, after his return, he initiated a project which culminated in the Neen engine, which at the time was the most powerful engine in the world,
34
with 5,000 pounds of thrust.
35
Possibly one of the most important but least publicized uses of this engine was its incorporation into the Russian MiG-15 aircraft, which was so effective in the Korean conflict.
36
One critical difference between the German engines used in the Heinkel and the later Messerschmitt 262, and those developed from Sir Frank Whittle's original engine,
37
was the type of compressor employed.
38
While the Whittle engine used a centrifugal compressor, similar to the example shown here,
39
the German engines, like the BMW 003 model used in the Heinkel 162,
40
utilized an axial flow compressor similar in design to the cutaway model shown.
41
Axial flow compressors have several advantages over the centrifugal compressor.
42
For instance, whereas the centrifugal compressor compression ratio is limited to approximately 12 to 1, when the maximum of two stages are used in series,
43
by adding more stages to an axial flow compressor, compression ratios as great as 40 to 1 can be obtained.
44
The term compression ratio refers to the ratio of the pressure at the outlet of a compressor to that at its inlet.
45
A second advantage of the axial flow compressor, almost as important as the first, is that the mass flow
46
which can be obtained through an axial flow compressor is potentially much greater than the mass flow
47
which can be achieved through a centrifugal compressor.
48
As a consequence of these factors, the development of the early centrifugal compressor engines was subjugated in favor of the advancement of the axial flow compressor engines,
49
which continues today.
50
The principle of the gas turbine engine is basically the same as that of the piston engine propeller combination.
51
They both propeller mass of air backwards.
52
Mass times acceleration equals force.
53
In a gas turbine engine the mass, m, mentioned in the equation is the air delivered by the compressor.
54
The acceleration in the equation is the difference in the outlet velocity of the air, V0, to that of its inlet velocity,
55
V1, due to the addition of heat energy.
56
Force equals mass times V0 minus V1, which equals thrust.
57
With the piston engine propeller combination, the propeller drives a relatively large mass of air backwards fairly slowly,
58
while the gas turbine throws a small mass of air backwards relatively quickly.
59
Newton's third law states, for every force acting on a body there is an equal and opposite reaction.
60
In the two cases quoted earlier, the piston engine propeller combination and the gas turbine engine,
61
the force created by the mass of air being thrown backwards and its velocity generates a reaction in the opposite direction, driving the aircraft forwards.
62
It must be remembered that the jet reaction does not result from the pressure of the jet on the atmosphere.
63
In all instances the resultant reaction
64
or thrust exerted on the engine is proportional to the mass
65
or weight of the air expelled by the engine and the velocity change imparted to it.
66
The working cycle of the gas turbine engine is called the Brayton cycle after George Brayton, an American mechanical engineer who invented the continuous ignition engine,
67
which was the basis of the gas turbine engine.
68
The Brayton cycle and the working cycle of the four-stroke piston engine, the Otto cycle, are very similar as can be seen in this diagram.
69
The induction, compression, Power and exhaust strokes of the Otto cycle are each matched by induction,
70
compression, combustion and exhaust stages in the Brayton cycle.
71
One major difference however exists in that in the gas turbine engine combustion theoretically occurs at a constant pressure,
72
whereas in the piston engine it occurs, once again theoretically, at a constant volume.
73
Power is developed in the turbine of the engine.
74
Other differences between the piston engine
75
and the gas turbine engine concern the continuous manner in which these processes occur in the gas turbine engine,
76
as opposed to the intermittent procedure occurring in the piston engine.
77
In the piston engine, only one of the strokes is utilized in producing power.
78
The other three are effectively absorbing power, while in the gas turbine engine, the three idle strokes have been eliminated,
79
thus allowing more time for the burning of fuel.
80
This is just one of the reasons why the gas turbine engine has a greater power-weight ratio than the piston engine.
81
The pressure volume diagram shown here, otherwise known as the Brayton cycle, represents the working cycle of the gas turbine engine in its simplest form.
82
Air, at atmospheric pressure, enters the engine at point A and is compressed along the line AB.
83
is added in the combustion chambers, which is signified by point B, and the mixture is burnt, in theory at a constant pressure.
84
In fact, the reduction in pressure shown between points B
85
and C indicates that pressure losses do actually occur in the combustion chamber.
86
The drop in pressure is created by the need to produce the swirl and turbulence necessary for efficient combustion,
87
and this causes a pressure drop throughout the combustion chamber length of between 3 to 6%.
88
Notwithstanding this drop, a considerable increase in the volume of the air is generated within the combustion chamber.
89
Between points C and D, the gas generated through combustion expands in the turbine,
90
where mechanical power is extracted from the energy in the gas stream,
91
and the jet pipe, where the remainder of the gas stream energy provides a propulsive jet as it's discharged.
92
In theory, the gas stream pressure attains a value equal to atmospheric pressure before being ejected.
App herunterladen
Alles, was du zum fließenden Sprechen brauchst
KI-AussprachebewertungJeder Satz bewertet
IPA-TrainingJeden Laut meistern
WortschatzBaue deinen Wortschatz auf
VokabelspielSpielend lernen
FOR YOU
Empfohlenes Video
C11
507 Sätze
Steam Turbine Construction Operating Fundamentals
Daily ConversationUniversity Students
C1118
15 Sätze
Could Humans Evolve Flight?
Daily ConversationUniversity StudentsWorking Adults
C14
153 Sätze
How Reusable Rockets Work
Daily ConversationUniversity StudentsWorking Adults
C11
19 Sätze
I Made an EMP Device... It Actually Works
Daily ConversationUniversity StudentsWorking Adults
C12
90 Sätze
Did Google just dethrone OpenAI and Anthropic?
Daily ConversationUniversity StudentsWorking Adults
C12
87 Sätze
Respiratory System 5, Podcast on breathing
Daily ConversationUniversity Students
C11
108 Sätze
How I Learned Procedural Generation
Daily ConversationUniversity StudentsWorking Adults
C12
12 Sätze
Plastic Injection Molding
Daily ConversationUniversity StudentsWorking Adults
B21
150 Sätze
Car Engine Parts & Their Functions Explained in Details | The Engineers Post
Daily ConversationUniversity Students
C12
138 Sätze
Derivatives: Crash Course Physics #2
Daily ConversationUniversity Students
C14
291 Sätze
How The World's Most Powerful Fighter Jet Engine Is Made
Daily ConversationWorking Adults
B22
41 Sätze
Why are airplanes slower than they used to be Alex Gendler
Daily ConversationUniversity StudentsWorking Adults
Kontext & Hintergrund
Das Video "Aircraft Gas Turbine Engines #01 - Introduction Part 1" erklärt die Grundlagen von Strahltriebwerken, von der Geschichte Hero von Alexandrias bis zu modernen Entwicklungen. Es kombiniert technische Begriffe mit anschaulichen Beispielen, was es ideal für Englischlerner macht, die ihre Sprachkenntnisse in einem fachlichen Kontext verbessern wollen. Mit "Englisch lernen mit Videos" kannst du nicht nur Wissen über Triebwerke aufbauen, sondern auch deine Hör- und Sprechfertigkeiten trainieren – perfekt für "Englisch sprechen üben"!
Top 5 Phrasen für den täglichen Gebrauch
- "Jet propulsion can be defined as..." – Perfekt, um Begriffe zu erklären. Übe es: "Kaffee can be defined as a hot drink made from roasted beans."
- "operates on the principle of..." – Nutze es, um Funktionsweisen zu beschreiben: "This machine operates on the principle of electricity."
- "a representation of which is shown here" – Nützlich, um Bilder oder Beispiele einzuführen: "A photo of my dog, a representation of which is shown here, was taken last week."
- "as a consequence of these factors" – Ideal für logische Folgerungen: "As a consequence of the rain, we stayed inside."
- "the principle of... is basically the same as..." – Gut, um Vergleiche zu ziehen: "The principle of baking a cake is basically the same as making cookies."
Schritt-für-Schritt-Shadowing-Anleitung
Shadowing (oder "shadowspeaks") ist eine tolle Methode, um deine Englisch-Sprechfertigkeiten zu verbessern. Hier ist wie du es mit diesem Video machst:
- Höre dir einen kurzen Abschnitt (5-10 Sekunden) an – Konzentriere dich auf die Intonation und den Rhythmus.
- Wiederhole sofort hinterher – Versuche, die Wörter so genau wie möglich nachzusprechen. "Shadow speak" heißt, du bist wie ein Schatten: direkt hinter dem Sprecher.
- Analysiere Schwierigkeiten – Hattest du Probleme mit "compression ratio"? Wiederhole den Abschnitt, bis es flüssig klappt.
- Erweitere die Abschnitte – Sobald du kurze Passagen beherrschst, nimm längere Stücke (30 Sekunden) auf.
- Mache es zu einem Ritual – Übe täglich 10 Minuten, und du wirst schnell Fortschritte sehen. "Englisch Shadowing" macht Spaß und bringt sofortige Erfolge!
Mit diesem Video und der richtigen Methode wirst du nicht nur technisches Englisch lernen, sondern auch selbstsicherer sprechen. Los geht's – dein nächster Schritt zum fließenden Englisch ist nur einen Klick entfernt!
Grammatik in diesem Video
Die Strukturen, die der Sprecher am häufigsten verwendet, mit den genauen Worten aus dem Video:
| Struktur | Im Video |
|---|---|
| Passiv be + Partizip Perfekt – wichtig ist, was geschieht, nicht wer es tut | can be defined · is generated · is shown |
| Relativsätze who / which + Satz – eine Zusatzinformation über eine Person oder Sache | another, which is · aircraft, which was · chambers, which is |
Was ist die Shadowing-Technik?
Shadowing ist eine wissenschaftlich fundierte Sprachlerntechnik, die ursprünglich für die professionelle Dolmetscherausbildung entwickelt und durch den Polyglotten Dr. Alexander Arguelles populär gemacht wurde. Die Methode ist einfach aber wirkungsvoll: Du hörst englisches Audio von Muttersprachlern und wiederholst es sofort laut — wie ein Schatten, der dem Sprecher mit nur 1–2 Sekunden Verzögerung folgt. Anders als passives Hören oder Grammatikübungen zwingt Shadowing dein Gehirn und deine Mundmuskulatur, gleichzeitig echte Sprachmuster zu verarbeiten und zu reproduzieren. Studien zeigen, dass es Aussprachegenauigkeit, Intonation, Rhythmus, verbundene Sprache, Hörverständnis und Sprechflüssigkeit signifikant verbessert — was es zu einer der effektivsten Methoden für die IELTS Speaking-Vorbereitung und reale englische Kommunikation macht.