शैडोइंग अभ्यास: Removing Creased Wrinkled Dent with PDR Crease Glue Tabs! | PDR Tips - YouTube के साथ अंग्रेजी बोलना सीखें

Today, removing creased wrinkle dent with PDR crease glue tabs.

⏸ रुका हुआ

गति:

146 वाक्य

यदि वाक्य बहुत छोटे या लंबे हों, तो समायोजित करने के लिए Edit पर क्लिक करें।

Today, removing creased wrinkle dent with PDR crease glue tabs.

Does your front wing or fender have creased wrinkle damage like this?

I'll be sharing lots of tips on removing the majority of this big dent with PDR hot glue crease tabs.

All the body repair shops in the area wanted to replace this panel for obvious reasons.

If you're a paint shop,

I'm going to show you how to save large damage like this.

Hello everyone,

I'm Clark Ken, the man of steel.

Today I will be working overtime on this Lexus 300.

Let's first start by tracking the dent.

Section number one, the wheel arched edge is gone.

By looking at the bumper,

it has collapsed over one inch.

Section number two, the headlight sticks out over a quarter of an inch.

Under the headlight, the fender is bent out over an inch.

Section number three, the fender and the hood gap is no longer there.

The top edge sticks out over a quarter of an inch.

Section number four, the rear section of the fender bracket on the back side is pushed in.

The door edge rubs against the fender.

The fifth section, the middle body line is crushed and creased with blown off paint.

The dent is deep and wrinkled.

The dent is over 40 inches in length.

The customer is happy to do his own touch-up.

I am now zooming into my customized paintless dent repair tool desk.

First tool on the list,

PDR rods and flat bar.

Two body repair dollies.

Next, three slide hammers and a PDR mini lifter,

a PDR light, two hammers and a sledge,

a pole jack, a hustler stick,

hot glue gun, two PDR knockdowns,

a variety of crease tabs,

alcohol spray and towel, 3M polish and buffer,

a torch and a drill.

Starting the body work repair using the paintless dent removal method.

Wiping the panel down with alcohol,

I am now grabbing my large crease tab and squeezing hot glue to the surface of the tab,

placing the tab directly along the body line.

Next, grabbing my second large crease tab,

again squeezing hot glue on the surface.

Now I'm writing my pull pin through the PDR tabs.

It's time to get my flex on and begin my first pull.

using the hustler stick like a frame rack.

I'm going to pull at the same time and stabilize the fender.

Removing the tab, getting ready for my second layer of complexity.

Second round of glue pulling.

This round, I'm running my first tab vertical in the deep crease.

I am placing my other tab going another direction.

This tab, I'm running horizontal.

I have been here many times,

so I'm just following my mental blueprint on big dents.

Let's take a closer look at this large damage smash.

I chose these crease tabs because they are wider and can grip and grab more surface on the metal.

Time to get my flex on again beginning the next pull.

If you shorten the chain you can change the degree on the angle of the pull.

The goal here is lining up the fender edge with the bumper edge.

These big dents come out much cleaner with large glue tabs

rather than pushing on the back side with rods and flat bars.

I'm going to grab my heavy-duty auto body slide him the

slide hammer is leveling up the tab the shadow left side

lifted quickly the slide hammer is going after the resistant deep area

removing the chain and the pin and the stabilizing bar the fender edge was crushed

and wrinkled it's beginning to take shape here's a couple of viewing angles

removing the glue tab now entering the third layer of complexity third round of glue pulling

using my third rotational set of glue tabs these crease tabs are curved to match the curve in the body line.

These tabs will help tremendously in restoring the shape back to the body panel.

Doing a series of controlled pulls on the curved crease tabs.

I'm going to use my powerful suction cup dent puller.

This is a pneumatic slide hammer,

has over 150 pounds of suction pressure.

This suction slide hammer is quicker than any large round hot glue tabs and it's 10 times stronger than any cold glue.

Now getting my flex on with the slide removing the deepest section of the dent in a matter of maybe a minute.

This suction cup keeps on grabbing with the continual airflow.

These cups never lose its grip.

This is a four inch cup.

I also have a six inch cup I use for quick pulls on crushed sideswipe panels at my shop.

I have made my money on this $80 tool many times over.

Probably one of my best investments.

The only drawback is you need an air compressor.

This is what we have after four pulls with the pneumatic auto body slide hammer.

next step i'm going to do some rni i'm going to remove screws

and clips so i can pull the bumper

and the headlight this time i'm going to fine tune the bracket and the outer frame Next set of pulls is critical.

Using the slide hammer to hammer forward the fender bracket.

This will help get the fender off the door.

Second, pulling the fender nose out to line up with the bumper.

Next, using a 10mm socket to loosen the entire upper section of the fender for realignment.

When was the last time you saw a dent pull like this on YouTube?

Hit the like and subscription button for my next PDR body repair.

The man of steel is going to make a few more pulls with his hands of steel.

There is additional damage on the backside.

The bracket is pushed in.

I will need to bring out to get the proper gap and spacing for the door and the fender.

Now opening the door so I can do another series of simple pulls on the fender edge.

The gap is now looking better.

Now moving on to my next layer of complexity,

lining up the nose section with a flat bar.

I'm going to place the bar behind the backside of the bumper bracket and push off the tire.

Going to use the bar in conjunction with the body repair dolly.

100

Going to hammer on dolly technique to remove the buckle in the edge.

101

The fender is slightly buckled outward.

102

Applying pressure to the back side of the dolly,

103

reaching for my plastic tip hammer and striking the buckle.

104

Next, knocking down the underside buckle.

105

The Man of Steel will use his hands once again.

106

I'm going to press in and line up the fender and strike the buckle.

107

Taking my plastic tip hammer and voila!

108

Now I'm going to make a series of glue pulls with my PDR mini lifter and slide hammer.

109

Applying hot glue to the tabs,

110

now placing it to the fender.

111

I'm leaning into the fender,

112

gripping both handles and pulling hard on the slide.

113

I I placed a large tab on the upper section of the fender.

114

I removed the nine pound hammer from the shaft,

115

placing the heavy duty hook through the eye bolt.

116

The reason why I removed the hammer,

117

it would hit too hard and open up the gap too far between the fender and the hood.

118

I'm going to use a 2x4 as a knockdown.

119

I'm going to give the top fender a few strikes.

120

Next, closing the hood to check the alignment and the gap.

121

Going to clean up around the headlight,

122

placing the body repair dolly up against the edge.

123

using a sharp Delrin tip on a paintless dent repair rod.

124

This panel has a lot of micro lows and highs

125

that I will need to fine tune with my remaining rotational PDR tools.

126

I will make a series of pushes from the back side and a series of knockdowns on the front side.

127

Zooming out, time to put the car back together using a common 10 millimeter socket.

128

I'm going to tighten up around the fender and around the headlight.

129

Attaching the bumper to the upper bumper bracket.

130

Putting back the engine compartment trim and locking the parts in with the vinyl clips.

131

the hood final step clean up the clear coat with a polish

132

and a buffer now I'm ready to show you the body

133

work using the paintless dent repair method let's check out the final results 해

134

rar rick voodoo voodoo

135

voodoo t

136

voodoo

137

Imm guilty

138

I want to thank you

139

for taking the time to watch my video.

140

If you're like me, you're going to get another dent.

141

Subscribe and I can help you keep your vehicle dent free.

142

I will see you in my next video.

143

You guys continue forging your future.

144

I'm signing off.

145

We'll be

146

right back.

TRENDING

शैडोइंग तकनीक क्या है?

शैडोइंग (Shadowing) एक विज्ञान-समर्थित भाषा सीखने की तकनीक है जो मूल रूप से पेशेवर दुभाषिया प्रशिक्षण के लिए विकसित की गई थी। विधि सरल लेकिन शक्तिशाली है: आप मूल अंग्रेज़ी ऑडियो सुनते हैं और तुरंत इसे ज़ोर से दोहराते हैं — जैसे वक्ता की छाया 1-2 सेकंड की देरी से। शोध से पता चलता है कि यह उच्चारण सटीकता, स्वर, लय, जुड़ी हुई ध्वनियाँ, सुनने की समझ और बोलने की प्रवाहशीलता में काफ़ी सुधार करता है।

☕ हमें एक कॉफी पिलाएं

आपके समर्थन के कारण ShadowingEnglish 100% मुफ्त है। सर्वर और AI की लागत अधिक है — आपकी कॉफी हमें आगे बढ़ने में मदद करती है! 🙏

PayPal के माध्यम से दान करें

ShadowingEnglish.com – अंग्रेज़ी शैडोइंग अभ्यास

शैडोइंग अभ्यास: Removing Creased Wrinkled Dent with PDR Crease Glue Tabs! | PDR Tips - YouTube के साथ अंग्रेजी बोलना सीखें

लोकप्रिय

इस वीडियो के साथ बोलने का अभ्यास क्यों करें?

संदर्भ में व्याकरण और अभिव्यक्तियाँ

सामान्य उच्चारण के जाल

शैडोइंग तकनीक क्या है?

शैडोइंग अभ्यास: Removing Creased Wrinkled Dent with PDR Crease Glue Tabs! | PDR Tips - YouTube के साथ अंग्रेजी बोलना सीखें

ऐप डाउनलोड करें

इस वीडियो के साथ बोलने का अभ्यास क्यों करें?

संदर्भ में व्याकरण और अभिव्यक्तियाँ

सामान्य उच्चारण के जाल

शैडोइंग तकनीक क्या है?