쉐도잉 연습: My Tesla Powered Boat Gets MAJOR Upgrades - 영상으로 영어 말하기 배우기

연습 모드 선택

각 모드는 전체 화면 연습실로 열립니다.

251 문장

문장이 너무 짧거나 길면 Edit를 눌러 조정하세요.

Welcome to episode 2 of the Tesla-powered mini jet boat build.

Today we're fixing the batteries and building a totally custom Tesla motor to power it.

It's so smooth.

In this project, we're learning so much about high-voltage electric drivelines while pushing the limits of what's possible with them.

At the end of this episode, we're doing the first successful test drive of the boat.

Let's start today by removing the batteries so we can fix them.

I'm standing in a metal boat, touching the live terminals.

Any last words?

Oh yeah!

Ah, so much more barren in here.

Next, let's pull out our Model 3 motor we put in in the last episode.

There's nothing particularly wrong with it.

I just don't like the inverter relocation mod, and I know we can do better.

So, I've identified the worst cell.

So this is a good cell here, 3.87, right here.

0.19 volts.

All the cells in this region right here are completely drained and they are unrecoverable.

Once they get below about two volts, they're completely shot.

The chemical makeup inside of them changes and they're no longer able to be charged again.

These are the two new modules we are replacing the junk ones with.

Now we have to make these four modules play nice together by balancing them out to the same voltage.

These two packs were at 92 volts, which is pretty full, so I need to drop them down to match these two at 83.

Luckily, it's pretty easy to remove power from a battery.

This is so awesome!

We're boiling water with just one of these modules.

These battery modules carry an insane capacity, and they have such low resistance that they can put out a ton of current.

I'm pulling about 30 amps with this little setup, but that is nothing for these liquid cooled batteries, they can put out over 600 amps each.

It's just crazy.

Now that the battery modules are balanced, we can get ready to reinstall them.

Version two of the battery boxes is going together way more professionally than the first round.

The last version had a bunch of silicone wrapped around all these bolts to seal it up

and it was super nasty looking.

You can't just put a rubber washer on these bolts

because they have a load on them and it'll just squish the rubber everywhere.

So I've come up with a solution.

I found these washers.

They're for like a hydraulic pump.

Those will tighten up and they can handle a ton of load while they're sealing with that rubber washer there.

They're not very cheap.

This was $400.

What have we done?

It's the best way to do it.

It's the only way.

I don't know what to tell you, man.

These electric projects are just expensive.

Since we're using an aftermarket battery management system, we can get rid of the Tesla control boards off of these new modules, just like last time.

And then we can add our cell tap wires that monitor and balance the voltage across each of our 96 cells.

Last time we soldered to these battery tabs and it did not work well.

So this time we're crimping to them.

It looks a little crude, but this is actually the best option here.

I'm upgrading all the wiring with removable plugs to make assembly and any repairs in the future a lot easier. is fully assembled

and i want to test the cooling system in each module we're just gonna put about 10 psi in

and let it hold for a little while make sure we don't have any leaks all good

finally we are sealing up the new batteries

looks so good this is our new motor

and this thing is gonna be crazy our model 3 motor was an impressive 280 horsepower,

but this custom-tuned Model S motor will make over 350 horsepower.

You know you're doing some sketchy stuff when they try to hide the bolts from you?

That know right where they're at.

You can see the gearing reduction here.

So that one's spinning 9.7 times slower than that one.

This is the RPM we're after.

Horsepower is great, but the coolest part about this motor is it can spin over 18 000 rpm

i've got the motor fully gutted now and we can check out how it works this is the inverter

that controls how much power the motor gets and the rotor The rotor lives in there like that,

and this is what generates the torque.

When this is in the car, there's a bunch of gears in here

that reduce the RPM of the motor to the axle outputs right here about 9 to 1,

but we need the full RPM of the motor.

The way we're going to do

that is by adding this custom stub shaft right into the tail end of this

and drive it all the way in so that we have the jet drive connected directly to the rotor on the motor.

It's also too wide to go in the boat just like this

and we don't need this whole section that used to carry all the gears

so we're going to slice it off and weld the cap on it.

Oh Now

we're gonna mill this part perfectly flat.

I'm not a machinist.

I'm using random parts to jig this thing up.

We're gonna ratchet strap it down and just run the mill into it, make it flat. That worked really good.

I can't believe it didn't fly off of here.

Wow.

Not bad.

Definitely good enough to weld to.

We got our oil pressure fitting installed.

This is definitely the world's first Tesla with an AN race fitting welded to the top of it for oiling.

Since we removed the internal oil pump and some of the gears that splash oil around,

I need to add a couple different ports to spray oil on our bearings to make sure they stay cool and lubricated.

Modifying the rotor was the key to the whole build here.

I had this section removed from this rotor.

Look at that.

So this is what it used to look like.

And I had a machine called a wire EDM that cut all the way around to the profile of our new shaft.

And it removed this blank.

It is unfathomably precise.

Like we're talking smaller than human hairs by like a thousand it.

Now that the rotor is bored out to the correct diameter, we can slide our new stub shaft in.

So we're going to have to chill this part down to shrink it and then slide it in.

I really wanted to use my liquid nitrogen for this, but I used it all up making ice cream.

100

I had this in the freezer for a few hours, so it's nice and shrunk down.

101

Hopefully it pops in.

102

If we mess this up, it's a really big deal.

103

It's going!

104

I think that's all we're gonna get.

105

That's okay.

106

It doesn't need to go in all the way.

107

It's definitely not gonna come out.

108

Sweet!

109

If I would have used the liquid nitrogen, it for sure would have went in all the way.

110

Oh baby!

111

This is now officially a jet boat motor.

112

This is the standard jet pump adapter flange.

113

That is so cool.

114

It is time to install our extremely custom modified Tesla rotor.

115

It's a real pain in the butt to get out.

116

If we mess this up, it's not good.

117

You can damage the bearings.

118

Oh my gosh.

119

Now we're going to put this cap on here.

120

And you see how that shaft lines up right here.

121

We just need to poke a hole in the top of this thing.

122

Stick the shaft out and then put a little seal right here.

123

That's it dude, we're done.

124

I made this little ceiling flange out of a piece of half-inch aluminum plate.

125

And I'm going to use a razor blade to scribe its perfect location on the housing

126

so I can take it off and weld it.

127

This thing fits perfect.

128

This is the stator.

129

This is what actually puts the current from the inverter into the rotor.

130

Oh yeah.

131

You have to put a lot of thought into how the whole system works before you can design parts. For example,

132

the diameter of this shaft is determined on the diameter of this bearing being able to slide over top of it.

133

If it was larger than that, we'd have a very big problem.

134

To get this shaft installed perfectly aligned with the factory rotor was not easy.

135

Lots of planning, redoing the oil system, cutting the case, everything to make this happen.

136

I'm so proud of this motor.

137

I think it's really going to work good.

138

This is the inverter.

139

What it does is it takes the two big DC power leads from your batteries

140

and converts it to a three-phase AC output to run the motor with all these control boards inside of here.

141

This inverter has a huge problem for us here, and that's that logo right there.

142

The stock control boarding here makes it really hard to control the motor when it's not in a Tesla vehicle.

143

But luckily for us, somebody else has spent a ridiculous amount of time developing a new one

144

that we can install and control this thing however we want.

145

We just need to pop off the Tesla control board, grab our new control board, and solder a few connectors to it.

146

Too easy, dude.

147

Too easy.

148

Got our aftermarket inverter board installed now

149

This motor is so close to not fitting.

150

There is an eighth inch of clearance on the bottom side, but I love how it looks in here.

151

Let's whip up some new motor mounts and modify the hull just a little bit to accept them. so Check

152

out our suspension system.

153

These rubber isolators are out of a military crate that held a jet engine.

154

Look how well this works.

155

They have their own suspension inside the boat.

156

I got my spacesuit gloves on.

157

We're doing the final install on the battery here.

158

Yeah, it didn't even explode this time.

159

Can't wait to see this motor spin.

160

I think we can do it today.

161

There we go.

162

We also need to redo all of the coolant hoses.

163

This is kind of fun.

164

There's a lot of crazy shapes.

165

This is my favorite because it looks like a little puppy.

166

We are ready to fill it up with coolant and oil.

167

I've got the motor full of oil so we can turn on the pump and test the flow.

168

It pulls out of the bottom of the case there

169

and comes in the top here and we get to see it draining into the case.

170

Wow, look at that.

171

What?

172

That's so cool.

173

Now we can hook it up.

174

Charge port sensor is plugged in.

175

Now we will see if it starts to charge.

176

No, wait.

177

It's charging.

178

Is charging power status on?

179

It's pulling nine amps.

180

Let's go.

181

I'm so pumped.

182

seeing this thing charge after all those hours of work really pays off

183

it's 3 30 in the morning i just got connected to

184

the inverter you actually use wi-fi for the upgraded board

185

that i put in there you can see we're connected to inverter

186

this is months in the making we are ready to spin over the model s motor in the boat

187

oh my gosh i'm so excited enable i'm gonna give it a little throttle and see if it spins

188

oh this thing is silent the model 3 motor is a lot louder let's go

189

There's a lot of little things to do, but I just want to get it on the water and make sure that it works.

190

You want to go with?

191

I got your harness in the mail today. Are you ready, dude?

192

Can't wait.

193

I'm so pumped.

194

Yeah, the last test drive we did was a year ago.

195

We didn't have time to put the seats in.

196

I hope that's in here.

197

Bro, are we gonna die?

198

Power on the motor.

199

For all the testing today, I'm gonna set the power limit to about 60% and the maximum RPM about 50%.

200

I think it's ready to go.

201

See, we got full bars of battery.

202

Fully charged.

203

I'm nervous.

204

Ready?

205

Dude!

206

She's working.

207

It's working.

208

Oh my gosh.

209

It sounds so smooth.

210

It's so quiet.

211

Oh, she wants to rip.

212

I guess we're just off to sea.

213

Okay, calm down.

214

When should we give it full power?

215

Not yet.

216

Floor it.

217

Oh crap!

218

Oh crap!

219

Dude!

220

No way!

221

What the heck?

222

Holy smokes!

223

That is insane!

224

Was that full throttle?

225

No!

226

That wasn't full throttle?

227

No!

228

Oh yeah, okay.

229

Holy crap!

230

What the heck?

231

We just went like 50 miles an hour.

232

That's crazy.

233

Like working on a project in the shop for three years and then the first time you take it out properly,

234

you have to turn your hat backwards because it is that fast.

235

It's 0 to 100.

236

Smoking up the whole environment.

237

Yeah, I am.

238

Couldn't be us.

239

Anyway, did you hear about that new lithium mine going in across the street?

240

Yep.

241

Dude, that's a great wreck.

242

This is so sick.

243

I can't believe it.

244

It's working so good.

245

We're gonna make a couple tweaks, maybe move the batteries forward a little bit, and then all we have to do is paint it, put in the windows, put on the stickers, just like little stuff.

246

Finally, after three years of working on it, it is functional.

247

We officially own a Tesla powered mini jet boat.

248

This is amazing.

249

In the next episode, we are finishing the jet boat build.

250

Huge thanks to Tubi for sponsoring this project.

251

Come back next week for episode 3, or if you want to watch the entire Build series right now, it is live on Tubi.

앱 다운로드

유창하게 말하는 데 필요한 모든 것

AI 발음 평가문장마다 점수 확인

IPA 발음 연습모든 소리 마스터

단어 학습나만의 단어장 만들기

단어 게임놀면서 외우기

QR 스캔

Download on theApp Store Get it onGoogle Play

FOR YOU

이 레슨의 어휘와 말하기 포인트

이 B2 수준 말하기 레슨은 영상 “My Tesla Powered Boat Gets MAJOR Upgrades”을(를) 바탕으로 합니다. 가장 자주 반복되는 단어는 다음과 같습니다: motor, rotor, boat. 이 영상에는 섀도잉할 문장 251개와 단어 2330개가 있습니다. 말하는 구간의 길이는 23:35입니다. 화자는 분당 약 99단어로 천천히 말해서 소리 하나하나를 따라 하기에 여유가 있습니다. 단어의 82%가 영어에서 가장 많이 쓰이는 3,000단어에 속합니다. 나머지는 연습 전에 미리 확인해 두세요.

이 영상의 핵심 어휘

영상에서 가장 어려운 단어 15개를 발음, 뜻과 함께 정리했습니다.

단어	발음	뜻
module 명사	/ˈmɑd͡ʒul/	모듈
weld 동사	/wɛld/	용접하다
horsepower 명사	/ˈhɔɹsˌpaʊɚ/	마력
volt 명사	/vəʊlt/	볼트
washer 명사	/ˈwɒʃə(ɹ)/	세탁기
modify 동사	/ˈmɑ.dɪˌfaɪ/	수정하다
voltage 명사	/ˈvəʊltɪd͡ʒ/	전압
bolt 명사	/boʊlt/	볼트
diameter 명사	/daɪˈæmɪdɚ/	지름, 직경
install 동사	/ɪnˈstɔl/	설치하다, 깔다
coolant 명사	/ˈkuːlənt/	냉각제, 랭각제
solder 명사	/ˈsɒl.də(ɹ)/	땜납
stub 명사	/stʌb/	그루, 그루터기
nitrogen 명사	/ˈnaɪ.tɹə.d͡ʒən/	질소
luckily 부사	/ˈlʌk.ɪ.li/	운 좋게, 다행(多幸)히

영상에 나오는 구동사

단어	발음	뜻
come back 동사		돌아오다
come out 동사	/ˌkʌm ˈaʊt/	나오다
get out 동사		나오다, 나가다
pull out 동사		회수(回收)하다

따라 말해 볼 만한 문장

영상에 나오는 짧고 완결된 문장으로, 일상 대화에서 그대로 쓸 수 있습니다:

We're boiling water with just one of these modules.
What have we done?
I don't know what to tell you, man.
You want to go with?
When should we give it full power?

이 영상의 문법

화자가 가장 많이 쓰는 문형을 영상 속 실제 표현과 함께 정리했습니다.

문형	영상 속 표현
“used to” used to + 동사 — 지금은 아닌 과거의 습관이나 상태	used to carry · used to look
현재완료 have/has + 과거분사 — 과거의 일이 지금도 관련이 있을 때	I've identified · I've come · have we done
수동태 be + 과거분사 — 누가 하는지보다 무슨 일이 일어나는지에 초점	be charged · are balanced · is plugged

주의할 발음

화자는 we're, I'm, gonna 같은 축약형과 약화된 형태를 72번 사용합니다. 들리는 대로 짧게 발음하세요.

“th” 소리: throttle /ˈθɹɔ.tl̩/, lithium /ˈlɪθi.əm/, eighth /eɪtθ/
“sh”와 “zh” 소리: shaft /ˈʃɑːft/, washer /ˈwɒʃə(ɹ)/, gosh /ɡɑːʃ/, machinist /məˈʃiː.nɪst/, relocation /ˌɹiːləʊˈkeɪʃən/
긴 단어 — 강세 위치에 주의: diameter /daɪˈæmɪdɚ/, relocation /ˌɹiːləʊˈkeɪʃən/, aluminum /əˈlu.mɪ.nəm/

한국어 화자가 어려워하는 소리:

/f/ — ㅍ(/p/)으로 바꾸지 말고 윗니를 아랫입술에 대기: shaft /ˈʃɑːft/, modify /ˈmɑ.dɪˌfaɪ/, flange /ˈflænd͡ʒ/, freezer /ˈfɹizɚ/, fixing /ˈfɪksɪŋ/
/v/ — ㅂ(/b/)과 구별하기: inverter /ɪnˈvɝt.ɚ/, volt /vəʊlt/, voltage /ˈvəʊltɪd͡ʒ/, glove /ɡlʌv/, convert /kənˈvɝt/
/z/ — ㅈ이 아니라 성대를 울리는 /s/: freezer /ˈfɹizɚ/, razor /ˈɹeɪzɚ/, hose /hoʊz/

이 영상으로 연습하는 방법

먼저 말하지 않고 영상을 끝까지 듣고 모르는 단어를 적어 둡니다.
보통 속도로 한 문장씩 섀도잉하고, 화자의 리듬과 맞을 때까지 반복합니다.
자신의 목소리를 녹음해 원본과 비교하고, module, weld, horsepower 같은 단어에 특히 주의합니다.

쉐도잉이란? 영어 실력을 빠르게 키우는 과학적 방법

쉐도잉(Shadowing)은 원래 전문 통역사 훈련을 위해 개발된 언어 학습 기법으로, 다언어 학자인 Dr. Alexander Arguelles에 의해 대중화된 방법입니다. 핵심 원리는 간단하지만 매우 강력합니다: 원어민의 영어를 들으면서 1~2초의 짧은 지연으로 즉시 소리 내어 따라 말하는 것——마치 '그림자(shadow)'처럼 화자를 따라가는 것입니다. 문법 공부나 수동적인 청취와 달리, 쉐도잉은 뇌와 입 근육이 동시에 실시간으로 영어를 처리하고 재현하도록 훈련합니다. 연구에 따르면 이 방법은 발음 정확도, 억양, 리듬, 연음, 청취력, 말하기 유창성을 크게 향상시킵니다. IELTS 스피킹 준비와 자연스러운 영어 소통을 원하는 분들에게 특히 효과적입니다.

섀도잉 방법: 단계별 전체 가이드 읽기 →

쉐도잉 연습: My Tesla Powered Boat Gets MAJOR Upgrades - 영상으로 영어 말하기 배우기

연습 모드 선택

앱 다운로드

추천 영상

I Built a Fully Autonomous Flying Umbrella

How A Combined Cycle Power Plant Works Gas Power Generation GE Power

Why China is winning the EV war

Inside The SpaceX Starfactory

15 Things You Didn't Know About Nikola Tesla

Basic Solar Components & How They Work - Solar Panels, Inverter, Batteries, & More Explained (Ep. 2)

CAE8 O TEST1 PART3

The Best TINY Tech on the Internet!

Someone Hit My Tesla & I Caught It On Camera

Jeremy Clarkson Bugatti Chiron Review | The Grand Tour Seizoen 3

I tried gaming on Linux...

How An Oil Tanker Works And Designed