Shadowing-Übung: Frequency Response An Introduction to Filters - Englisch Sprechen Lernen mit Video

Übungsmodus wählen

Jeder Modus öffnet einen Übungsraum im Vollbild.

110 Sätze
Wenn Sätze zu kurz oder zu lang sind, klicke auf Edit, um sie anzupassen.
1
Alright, let's talk about frequency response and filters.
2
So, frequency response is basically we are going to be looking at circuits and the input circuit,
3
the input to the circuit is going to have more than one frequency or a frequency sweep.
4
So, instead of just a single 60 Hz signal, the input voltage might contain multiple 60 Hz,
5
50 Hz, 120 Hz, 121 Hz and so forth.
6
And we want to find out how the circuit output will respond to an input with such varying frequency.
7
So that's called frequency response.
8
And today the goal is to talk about filters.
9
So what are filters?
10
So consider this.
11
Consider this noisy ECG signal.
12
So here's the ECG signal.
13
You can see the peaks and the valleys, but you do see a lot of noise in that signal.
14
If we put this through a RLC circuit of a particular configuration, and we'll talk about those configurations later on,
15
what we can get is a much cleaner -looking signal from which we can decipher a lot more important information.
16
So we put in a noisy signal into an RLC circuit, what came out was a clean -looking signal.
17
So essentially what a filter is, and exactly as the English word means, it filters out certain unwanted components.
18
And in this case, the unwanted components might have been high -frequency noise.
19
So a filter is essentially an electronic circuit which performs some kind of signal processing function.
20
And specifically, it's intended to remove unwanted signal components,
21
or it's intended to enhance the components of the signal that we want to keep.
22
Now, there are a number of types of filters.
23
There are basically four types low -pass filter, which is shown on the top left right here,
24
allows lower signal frequencies, so frequency starting at DC all the way to some lower value to pass,
25
and anything else beyond that does not pass.
26
So what this is showing is the magnitude, so imagine a signal coming through and is being multiplied by this particular thing, okay?
27
So this is a gain of one, let's say, right at this point, so we'll call this a gain of 1.
28
We'll call this a gain of 1.
29
So any signal that comes in, let's say here's my signal that's coming in, I multiply that.
30
What I essentially have is the frequencies that are beyond, below this point.
31
And by the way, this was the frequency of the input signal.
32
Any frequency that's beyond this passes, anything that at this point does not pass,
33
anything around this point right here does not pass, this right here does not pass.
34
So we have only the lower frequencies passing, so it's called a low -pass filter.
35
The opposite side of this is called a high -pass filter.
36
So the lower frequencies do not go through, meaning the output is equal to zero whenever the frequency of the input is low.
37
All the higher frequencies pass through, so that's called a high -pass filter.
38
A bandpass filter is a filter that allows signals within a band of frequencies, somewhere in the middle.
39
Not the lower frequencies, not the higher frequencies to pass through, but a small band in the middle to pass through.
40
For example, FM station, 91 .1.
41
91 .1 is a particular frequency that is right in between the lower frequencies and the higher frequencies.
42
So when I tune my car radio to 91 .1, I should be getting only MPR.
43
So the lower side does not pass, the higher side does not pass, only 91 .1 passes, so that's called band pass filter.
44
The opposite of band pass filter is called a band stop filter.
45
We want to allow the lower frequencies to pass, higher frequencies to pass, but a smaller band not to pass.
46
Now when we connect AC equipment, because our AC signals are 60 Hz,
47
what we see is on top of whatever it is
48
that we're measuring we might see what is known as a 60 Hertz hum meaning a noise
49
or a 60 Hertz component
50
that is not really a part of the signal it comes in
51
because it's connected to an AC outlet now we want to be able to get rid of
52
that 60 Hertz in
53
that case we would use this band stop filter where we would allow every frequency that's not 60 hertz to pass.
54
On the lower side, any frequency above 60 hertz to pass, but we want to prevent the 60 hertz from passing.
55
So that's called a band stop filter.
56
Now these are all ideal looking filters.
57
No real realistic circuit can produce such sharp response between what is allowed and what is not allowed.
58
So you can't really get directly jumped like these.
59
So what ends up happening is more.. the black lines
60
that you see right here those are more realistic filters
61
so the chains or allowing of the high frequencies or the low frequencies is not as abrupt as i indicated in
62
here earlier it's more subtle than that
63
so more realistic filters look like these now what do these things really mean
64
so let's take a quick look at low pass filter what those were was a plot of magnitude response of the filter,
65
meaning it's a plot of magnitude against frequency on the x -axis.
66
The x -axis is the frequency, y -axis is the magnitude.
67
When we are dealing with filters, there is one more plot we're interested in,
68
which is the phase angle of the output changes with respect to the phase angle of the input.
69
So phase angle versus frequency plot is also interesting whenever we're dealing with frequency response,
70
but we'll look at that later on when we discuss specific type of filters.
71
So here is a generic low -pass filter.
72
A couple of points I want to highlight.
73
So this is a plot of the linear magnitude versus linear frequency.
74
Later on we'll see how we can represent a lot longer list of frequencies using something called Bode plots.
75
But for now, linear frequency in the x -axis, linear magnitude in the y -axis, 1 basically means the ratio of the output to the input.
76
Vout over Vin is equal to 1.
77
That means whatever is at the input is being passed towards the output.
78
Okay, this special point right here, 1 over square root 2 in terms of the magnitude has a special function.
79
That is equal to 0 .707.
80
So that's 0 .707.
81
Whatever the magnitude of 0 .707 of the maximum magnitude, so in this case, the maximum magnitude is 1,
82
that particular thing has a special name that's called the cutoff frequency.
83
So cutoff frequency is basically the term understood as frequencies after which the filter does not pass.
84
So that's where the filter cutoff into what passes and what does not pass basically lies.
85
So in this example right here, this abrupt line right here, that was the cutoff frequency.
86
Whereas in a more realistic filter, that would be at 1 square root of 2 of the maximum value.
87
Now in the case of a high -pass filter, this is the cutoff frequency.
88
That's the cutoff frequency.
89
But in a realistic filter, that is the cutoff frequency, 0 .707.
90
In the case of bandpass filter, we have two cutoff frequencies because we have the lower cutoff and the higher cutoff.
91
Same thing in the band stop filter, lower cutoff and higher cutoff.
92
So cutoff frequency basically decide what falls in this region.
93
In the case of the low pass filter, these are the frequencies that pass, and these are the frequencies that do not pass.
94
So that's called a pass band, that's called a stop band.
95
So that is a general idea behind filters.
96
Now, most RLC circuit we're going to look at, RLC circuit, most of them, in fact, all of the circuits that have only R,
97
L, and C components are called passive filters, meaning the output can only be as high as the input.
98
Vout equals Vin is maximum we're going to be able to get.
99
So the ratio of Vout over Vin in these RLC circuits are going to be maximum of 1.
100
Later on, we'll also look at active filters.
101
Active filters employ op -amps in them.
102
When we were dealing with op -amps,
103
we saw that we could use the op -amp and the negative feedback to control the gain of the output, meaning in an op -amp,
104
the output could be higher than the input value.
105
So active filters can have a gain that is greater than one, which is dictated by, again,
106
certain configurations of resistors placed in the feedback path.
107
Well, we'll talk about those later, but for now, we'll basically say that RLC circuits are just RLC -based filters are called passive filters
108
because the maximum gain they have is one, whereas op -amp -based filters are called active filters because the gain can be more than one.
109
In the next video, we'll take a look at some simple RC configuration
110
and look at an RLC configuration and look at low -pass, high -pass, and band -pass filters.

App herunterladen

Alles, was du zum fließenden Sprechen brauchst

KI-AussprachebewertungJeder Satz bewertet
IPA-TrainingJeden Laut meistern
WortschatzBaue deinen Wortschatz auf
VokabelspielSpielend lernen
FOR YOU

Empfohlenes Video

Wortschatz und Sprechhinweise zu dieser Lektion

Diese Sprechübung basiert auf dem Video „Frequency Response An Introduction to Filters“. Diese Wörter kommen am häufigsten vor: filter, pass, frequency, frequencies, signal. Dieses Video enthält 110 Sätze und 1500 Wörter zum Nachsprechen. Der gesprochene Teil dauert 9:27. Der Sprecher spricht in natürlichem Tempo, etwa 159 Wörter pro Minute, ähnlich wie im Alltagsgespräch. Nur 77 % der Wörter gehören zu den 3.000 häufigsten im Englischen, der Wortschatz ist also anspruchsvoll.

Wichtiger Wortschatz in diesem Video

15 lernenswerte Wörter aus dem Video, mit Aussprache und Bedeutung:

WortAusspracheBedeutung
frequency Substantiv/ˈfɹiːkwənsi/Häufigkeit, Frequenz
filter Substantiv/ˈfɪltɚ/Filter
circuit Substantiv/ˈsɝ.kɪt/Umlauf
magnitude Substantiv/ˈmæɡnɪtjuːd/Betrag
output Substantiv/ˈaʊtpʊt/Output
component Substantiv/kəmˈpoʊ.nənt/Komponente
realistic Adjektiv/ˌɹɪəˈlɪs.tɪk/realistisch
axis Substantiv/ˈæksɪs/Achse
configuration Substantiv/kənˌfɪɡ.əˈɹeɪ̯.ʃən/Konfiguration
linear Adjektiv/ˈlɪn.i.əɹ/linear
essentially Adverb/ɪˈsɛnʃəli/im Wesentlichen, im Grunde
angle Substantiv/ˈæŋ.ɡəl/Winkel
unwanted Adjektiv/ʌnˈwɒntɪd/unerwünscht, ungewollt
whereas/(h)wɛɹˈæz/wohingegen, wogegen
connect Verb/kəˈnɛkt/verbinden

Phrasal Verbs, die du hören wirst

WortAusspracheBedeutung
come out Verb/ˌkʌm ˈaʊt/herauskommen
end up Verbsich herausstellen, am Ende irgendwo / etwas sein
find out Verbherausfinden, erfahren

Grammatik in diesem Video

Die Strukturen, die der Sprecher am häufigsten verwendet, mit den genauen Worten aus dem Video:

StrukturIm Video
Passiv be + Partizip Perfekt – wichtig ist, was geschieht, nicht wer es tutis shown · being multiplied · is called
Relativsätze who / which + Satz – eine Zusatzinformation über eine Person oder Sachefilter, which is · one, which is

Aussprache, auf die du achten solltest

Der Sprecher verwendet 15 Kurzformen und abgeschwächte Formen, zum Beispiel we'll, we're, can't. Sprich sie in der kurzen Form, so wie du sie hörst.

  • Die Laute „sh“ und „zh“: configuration /kənˌfɪɡ.əˈɹeɪ̯.ʃən/, essentially /ɪˈsɛnʃəli/, ratio /ˈɹeɪ.ʃoʊ/, sharp /ʃɑɹp/
  • Lange Wörter – auf die Betonung achten: configuration /kənˌfɪɡ.əˈɹeɪ̯.ʃən/, essentially /ɪˈsɛnʃəli/

Laute, die Deutschsprachigen schwerfallen:

  • /w/ — mit runden Lippen, nicht wie das deutsche „w“ (/v/): frequency /ˈfɹiːkwənsi/, unwanted /ʌnˈwɒntɪd/, whereas /(h)wɛɹˈæz/, sweep /swiːp/
  • Stimmhafter Auslaut — /b/, /d/, /g/, /z/, /v/ am Wortende nicht verhärten: bind /ˈbaɪ̯nd/, magnitude /ˈmæɡnɪtjuːd/, unwanted /ʌnˈwɒntɪd/, whereas /(h)wɛɹˈæz/, intend /ɪnˈtɛnd/
  • /æ/ — offener als „ä“: magnitude /ˈmæɡnɪtjuːd/, axis /ˈæksɪs/, angle /ˈæŋ.ɡəl/, whereas /(h)wɛɹˈæz/, feedback /ˈfiːdˌbæk/

So übst du mit diesem Video

  1. Höre dir das ganze Video einmal an, ohne zu sprechen, und notiere die Wörter, die du nicht kennst.
  2. Beginne mit 0,75-facher Geschwindigkeit, sprich Satz für Satz nach und wechsle zur normalen Geschwindigkeit, sobald es leichtfällt.
  3. Nimm dich auf und vergleiche mit dem Original; achte dabei auf Wörter wie frequency, filter, circuit.

Was ist die Shadowing-Technik?

Shadowing ist eine wissenschaftlich fundierte Sprachlerntechnik, die ursprünglich für die professionelle Dolmetscherausbildung entwickelt und durch den Polyglotten Dr. Alexander Arguelles populär gemacht wurde. Die Methode ist einfach aber wirkungsvoll: Du hörst englisches Audio von Muttersprachlern und wiederholst es sofort laut — wie ein Schatten, der dem Sprecher mit nur 1–2 Sekunden Verzögerung folgt. Anders als passives Hören oder Grammatikübungen zwingt Shadowing dein Gehirn und deine Mundmuskulatur, gleichzeitig echte Sprachmuster zu verarbeiten und zu reproduzieren. Studien zeigen, dass es Aussprachegenauigkeit, Intonation, Rhythmus, verbundene Sprache, Hörverständnis und Sprechflüssigkeit signifikant verbessert — was es zu einer der effektivsten Methoden für die IELTS Speaking-Vorbereitung und reale englische Kommunikation macht.

Shadowing-Technik: die vollständige Schritt-für-Schritt-Anleitung lesen →