Shadowing Practice: Frequency Response An Introduction to Filters - Learn English Speaking with Video

בחר מצב תרגול

כל מצב פותח חדר תרגול במסך מלא.

110 משפטים
אם המשפטים קצרים או ארוכים מדי, לחץ על ערוך כדי להתאים אותם.
1
Alright, let's talk about frequency response and filters.
2
So, frequency response is basically we are going to be looking at circuits and the input circuit,
3
the input to the circuit is going to have more than one frequency or a frequency sweep.
4
So, instead of just a single 60 Hz signal, the input voltage might contain multiple 60 Hz,
5
50 Hz, 120 Hz, 121 Hz and so forth.
6
And we want to find out how the circuit output will respond to an input with such varying frequency.
7
So that's called frequency response.
8
And today the goal is to talk about filters.
9
So what are filters?
10
So consider this.
11
Consider this noisy ECG signal.
12
So here's the ECG signal.
13
You can see the peaks and the valleys, but you do see a lot of noise in that signal.
14
If we put this through a RLC circuit of a particular configuration, and we'll talk about those configurations later on,
15
what we can get is a much cleaner -looking signal from which we can decipher a lot more important information.
16
So we put in a noisy signal into an RLC circuit, what came out was a clean -looking signal.
17
So essentially what a filter is, and exactly as the English word means, it filters out certain unwanted components.
18
And in this case, the unwanted components might have been high -frequency noise.
19
So a filter is essentially an electronic circuit which performs some kind of signal processing function.
20
And specifically, it's intended to remove unwanted signal components,
21
or it's intended to enhance the components of the signal that we want to keep.
22
Now, there are a number of types of filters.
23
There are basically four types low -pass filter, which is shown on the top left right here,
24
allows lower signal frequencies, so frequency starting at DC all the way to some lower value to pass,
25
and anything else beyond that does not pass.
26
So what this is showing is the magnitude, so imagine a signal coming through and is being multiplied by this particular thing, okay?
27
So this is a gain of one, let's say, right at this point, so we'll call this a gain of 1.
28
We'll call this a gain of 1.
29
So any signal that comes in, let's say here's my signal that's coming in, I multiply that.
30
What I essentially have is the frequencies that are beyond, below this point.
31
And by the way, this was the frequency of the input signal.
32
Any frequency that's beyond this passes, anything that at this point does not pass,
33
anything around this point right here does not pass, this right here does not pass.
34
So we have only the lower frequencies passing, so it's called a low -pass filter.
35
The opposite side of this is called a high -pass filter.
36
So the lower frequencies do not go through, meaning the output is equal to zero whenever the frequency of the input is low.
37
All the higher frequencies pass through, so that's called a high -pass filter.
38
A bandpass filter is a filter that allows signals within a band of frequencies, somewhere in the middle.
39
Not the lower frequencies, not the higher frequencies to pass through, but a small band in the middle to pass through.
40
For example, FM station, 91 .1.
41
91 .1 is a particular frequency that is right in between the lower frequencies and the higher frequencies.
42
So when I tune my car radio to 91 .1, I should be getting only MPR.
43
So the lower side does not pass, the higher side does not pass, only 91 .1 passes, so that's called band pass filter.
44
The opposite of band pass filter is called a band stop filter.
45
We want to allow the lower frequencies to pass, higher frequencies to pass, but a smaller band not to pass.
46
Now when we connect AC equipment, because our AC signals are 60 Hz,
47
what we see is on top of whatever it is
48
that we're measuring we might see what is known as a 60 Hertz hum meaning a noise
49
or a 60 Hertz component
50
that is not really a part of the signal it comes in
51
because it's connected to an AC outlet now we want to be able to get rid of
52
that 60 Hertz in
53
that case we would use this band stop filter where we would allow every frequency that's not 60 hertz to pass.
54
On the lower side, any frequency above 60 hertz to pass, but we want to prevent the 60 hertz from passing.
55
So that's called a band stop filter.
56
Now these are all ideal looking filters.
57
No real realistic circuit can produce such sharp response between what is allowed and what is not allowed.
58
So you can't really get directly jumped like these.
59
So what ends up happening is more.. the black lines
60
that you see right here those are more realistic filters
61
so the chains or allowing of the high frequencies or the low frequencies is not as abrupt as i indicated in
62
here earlier it's more subtle than that
63
so more realistic filters look like these now what do these things really mean
64
so let's take a quick look at low pass filter what those were was a plot of magnitude response of the filter,
65
meaning it's a plot of magnitude against frequency on the x -axis.
66
The x -axis is the frequency, y -axis is the magnitude.
67
When we are dealing with filters, there is one more plot we're interested in,
68
which is the phase angle of the output changes with respect to the phase angle of the input.
69
So phase angle versus frequency plot is also interesting whenever we're dealing with frequency response,
70
but we'll look at that later on when we discuss specific type of filters.
71
So here is a generic low -pass filter.
72
A couple of points I want to highlight.
73
So this is a plot of the linear magnitude versus linear frequency.
74
Later on we'll see how we can represent a lot longer list of frequencies using something called Bode plots.
75
But for now, linear frequency in the x -axis, linear magnitude in the y -axis, 1 basically means the ratio of the output to the input.
76
Vout over Vin is equal to 1.
77
That means whatever is at the input is being passed towards the output.
78
Okay, this special point right here, 1 over square root 2 in terms of the magnitude has a special function.
79
That is equal to 0 .707.
80
So that's 0 .707.
81
Whatever the magnitude of 0 .707 of the maximum magnitude, so in this case, the maximum magnitude is 1,
82
that particular thing has a special name that's called the cutoff frequency.
83
So cutoff frequency is basically the term understood as frequencies after which the filter does not pass.
84
So that's where the filter cutoff into what passes and what does not pass basically lies.
85
So in this example right here, this abrupt line right here, that was the cutoff frequency.
86
Whereas in a more realistic filter, that would be at 1 square root of 2 of the maximum value.
87
Now in the case of a high -pass filter, this is the cutoff frequency.
88
That's the cutoff frequency.
89
But in a realistic filter, that is the cutoff frequency, 0 .707.
90
In the case of bandpass filter, we have two cutoff frequencies because we have the lower cutoff and the higher cutoff.
91
Same thing in the band stop filter, lower cutoff and higher cutoff.
92
So cutoff frequency basically decide what falls in this region.
93
In the case of the low pass filter, these are the frequencies that pass, and these are the frequencies that do not pass.
94
So that's called a pass band, that's called a stop band.
95
So that is a general idea behind filters.
96
Now, most RLC circuit we're going to look at, RLC circuit, most of them, in fact, all of the circuits that have only R,
97
L, and C components are called passive filters, meaning the output can only be as high as the input.
98
Vout equals Vin is maximum we're going to be able to get.
99
So the ratio of Vout over Vin in these RLC circuits are going to be maximum of 1.
100
Later on, we'll also look at active filters.
101
Active filters employ op -amps in them.
102
When we were dealing with op -amps,
103
we saw that we could use the op -amp and the negative feedback to control the gain of the output, meaning in an op -amp,
104
the output could be higher than the input value.
105
So active filters can have a gain that is greater than one, which is dictated by, again,
106
certain configurations of resistors placed in the feedback path.
107
Well, we'll talk about those later, but for now, we'll basically say that RLC circuits are just RLC -based filters are called passive filters
108
because the maximum gain they have is one, whereas op -amp -based filters are called active filters because the gain can be more than one.
109
In the next video, we'll take a look at some simple RC configuration
110
and look at an RLC configuration and look at low -pass, high -pass, and band -pass filters.

הורד אפליקציה

כל מה שאתה צריך כדי לדבר בשטף

הגיית AIציון לכל משפט
תרגול IPAשלוט בכל צליל
אוצר מיליםבנה את מאגר המילים שלך
משחק אוצר מיליםלמד תוך כדי משחק
FOR YOU

המלץ על סרטון

אוצר מילים והערות הגייה לשיעור הזה

שיעור הדיבור הזה מבוסס על הסרטון “Frequency Response An Introduction to Filters”. המילים שחוזרות הכי הרבה: filter, pass, frequency, frequencies, signal. בסרטון הזה יש 110 משפטים ו-1500 מילים לתרגול Shadowing. הדיבור נמשך 9:27. הדובר מדבר בקצב טבעי של כ-159 מילים בדקה, קרוב לשיחה יומיומית. רק 77% מהמילים נמצאות בין 3,000 המילים הנפוצות ביותר באנגלית, כך שאוצר המילים מאתגר.

אוצר מילים מרכזי בסרטון הזה

15 מילים מהסרטון שכדאי ללמוד, עם ההגייה והמשמעות שלהן:

מילההגייהמשמעות
frequency שם עצם/ˈfɹiːkwənsi/תדירות
filter שם עצם/ˈfɪltɚ/מַסנֵן
input שם עצם/ˈɪnpʊt/תְּרוּמָה
output שם עצם/ˈaʊtpʊt/פֶּלֶט
component שם עצם/kəmˈpoʊ.nənt/מַרְכִּיב, רְכִיב
realistic שם תואר/ˌɹɪəˈlɪs.tɪk/רֵיאָלִיסְטִי
axis שם עצם/ˈæksɪs/ציר
angle שם עצם/ˈæŋ.ɡəl/פינה, זווית
whereas/(h)wɛɹˈæz/הוֹאִיל
connect פועל/kəˈnɛkt/חיבר
ratio שם עצם/ˈɹeɪ.ʃoʊ/יחס
feedback שם עצם/ˈfiːdˌbæk/פִידְבֶּק
versus/ˈvɝsəs/נֶגֶד
noisy שם תואר/ˈnɔɪzi/רועש
sharp שם תואר/ʃɑɹp/חַד, שָׁנוּן

Phrasal verbs שתשמעו

מילההגייהמשמעות
come out פועל/ˌkʌm ˈaʊt/יָצָא

דקדוק בסרטון הזה

המבנים שהדובר משתמש בהם הכי הרבה, עם המילים המדויקות מהסרטון:

מבנהבסרטון
סביל (Passive voice) be + past participle — הדגש הוא על מה שקורה, לא על מי שעושה את הפעולהis shown · being multiplied · is called
משפטי זיקה (Relative clauses) who / which + clause — מידע נוסף על אדם או דברfilter, which is · one, which is

הגייה ששווה לשים לב אליה

הדובר משתמש ב-15 קיצורים וצורות מקוצרות, כמו we'll, we're, can't. אמרו אותם בצורה הקצרה, כפי שאתם שומעים אותם.

  • הצלילים של “sh” ו-“zh”: configuration /kənˌfɪɡ.əˈɹeɪ̯.ʃən/, essentially /ɪˈsɛnʃəli/, ratio /ˈɹeɪ.ʃoʊ/, sharp /ʃɑɹp/
  • מילים ארוכות — שימו לב להטעמה: configuration /kənˌfɪɡ.əˈɹeɪ̯.ʃən/, essentially /ɪˈsɛnʃəli/

צלילים שדוברי עברית מתקשים בהם:

  • /w/ — שפתיים מעוגלות, לא /v/: frequency /ˈfɹiːkwənsi/, unwanted /ʌnˈwɒntɪd/, whereas /(h)wɛɹˈæz/, sweep /swiːp/
  • /æ/ — פתוח יותר מה-“אֶ” העברית, לא כמו “a” ב-“cup”: magnitude /ˈmæɡnɪtjuːd/, axis /ˈæksɪs/, angle /ˈæŋ.ɡəl/, whereas /(h)wɛɹˈæz/, feedback /ˈfiːdˌbæk/
  • /r/ — הלשון לא נוגעת בשום מקום, לא ה-“ר” הגרונית: frequency /ˈfɹiːkwənsi/, realistic /ˌɹɪəˈlɪs.tɪk/, configuration /kənˌfɪɡ.əˈɹeɪ̯.ʃən/, linear /ˈlɪn.i.əɹ/, whereas /(h)wɛɹˈæz/

איך לתרגל עם הסרטון הזה

  1. הקשיבו לכל הסרטון פעם אחת בלי לדבר, ורשמו את המילים שאתם לא מכירים.
  2. התחילו במהירות 0.75×, תרגלו Shadowing משפט אחר משפט, וחזרו למהירות רגילה כשזה מרגיש קל.
  3. הקליטו את עצמכם והשוו למקור, תוך תשומת לב למילים כמו frequency, filter, input.

מהי טכניקת השאדואינג?

שאדואינג היא טכניקת למידת שפה מבוססת מדע שפותחה במקור להכשרת מתורגמנים מקצועיים ופופולרית על ידי הפוליגלוט ד"ר אלכסנדר ארגואלס. השיטה פשוטה אך עוצמתית: אתה מקשיב לאודיו באנגלית ילידית וחוזר עליו בקול רם מיד — כמו צל העוקב אחרי הדובר עם עיכוב של 1–2 שניות בלבד. בניגוד להאזנה פסיבית או תרגילי דקדוק, שאדואינג מכריח את המוח והשרירים בפה לעבד ולשחזר דפוסי דיבור אמיתיים בו זמנית. מחקרים מראים שזה משפר משמעותית את דיוק ההגייה, האינטונציה, הקצב, הדיבור המחובר, הבנת השמיעה ושטף הדיבור — מה שהופך אותו לאחת השיטות היעילות ביותר להכנה לIELTS Speaking ולתקשורת באנגלית בעולם האמיתי.

טכניקת Shadowing: קרא את המדריך המלא שלב אחר שלב →