跟读练习: Frequency Response An Introduction to Filters - 通过视频学习英语口语
选择练习模式
每种模式都会打开全屏练习室。
110 句
如果句子过短或过长,请点击 Edit 进行调整。
1
Alright, let's talk about frequency response and filters.
2
So, frequency response is basically we are going to be looking at circuits and the input circuit,
3
the input to the circuit is going to have more than one frequency or a frequency sweep.
4
So, instead of just a single 60 Hz signal, the input voltage might contain multiple 60 Hz,
5
50 Hz, 120 Hz, 121 Hz and so forth.
6
And we want to find out how the circuit output will respond to an input with such varying frequency.
7
So that's called frequency response.
8
And today the goal is to talk about filters.
9
So what are filters?
10
So consider this.
11
Consider this noisy ECG signal.
12
So here's the ECG signal.
13
You can see the peaks and the valleys, but you do see a lot of noise in that signal.
14
If we put this through a RLC circuit of a particular configuration, and we'll talk about those configurations later on,
15
what we can get is a much cleaner -looking signal from which we can decipher a lot more important information.
16
So we put in a noisy signal into an RLC circuit, what came out was a clean -looking signal.
17
So essentially what a filter is, and exactly as the English word means, it filters out certain unwanted components.
18
And in this case, the unwanted components might have been high -frequency noise.
19
So a filter is essentially an electronic circuit which performs some kind of signal processing function.
20
And specifically, it's intended to remove unwanted signal components,
21
or it's intended to enhance the components of the signal that we want to keep.
22
Now, there are a number of types of filters.
23
There are basically four types low -pass filter, which is shown on the top left right here,
24
allows lower signal frequencies, so frequency starting at DC all the way to some lower value to pass,
25
and anything else beyond that does not pass.
26
So what this is showing is the magnitude, so imagine a signal coming through and is being multiplied by this particular thing, okay?
27
So this is a gain of one, let's say, right at this point, so we'll call this a gain of 1.
28
We'll call this a gain of 1.
29
So any signal that comes in, let's say here's my signal that's coming in, I multiply that.
30
What I essentially have is the frequencies that are beyond, below this point.
31
And by the way, this was the frequency of the input signal.
32
Any frequency that's beyond this passes, anything that at this point does not pass,
33
anything around this point right here does not pass, this right here does not pass.
34
So we have only the lower frequencies passing, so it's called a low -pass filter.
35
The opposite side of this is called a high -pass filter.
36
So the lower frequencies do not go through, meaning the output is equal to zero whenever the frequency of the input is low.
37
All the higher frequencies pass through, so that's called a high -pass filter.
38
A bandpass filter is a filter that allows signals within a band of frequencies, somewhere in the middle.
39
Not the lower frequencies, not the higher frequencies to pass through, but a small band in the middle to pass through.
40
For example, FM station, 91 .1.
41
91 .1 is a particular frequency that is right in between the lower frequencies and the higher frequencies.
42
So when I tune my car radio to 91 .1, I should be getting only MPR.
43
So the lower side does not pass, the higher side does not pass, only 91 .1 passes, so that's called band pass filter.
44
The opposite of band pass filter is called a band stop filter.
45
We want to allow the lower frequencies to pass, higher frequencies to pass, but a smaller band not to pass.
46
Now when we connect AC equipment, because our AC signals are 60 Hz,
47
what we see is on top of whatever it is
48
that we're measuring we might see what is known as a 60 Hertz hum meaning a noise
49
or a 60 Hertz component
50
that is not really a part of the signal it comes in
51
because it's connected to an AC outlet now we want to be able to get rid of
52
that 60 Hertz in
53
that case we would use this band stop filter where we would allow every frequency that's not 60 hertz to pass.
54
On the lower side, any frequency above 60 hertz to pass, but we want to prevent the 60 hertz from passing.
55
So that's called a band stop filter.
56
Now these are all ideal looking filters.
57
No real realistic circuit can produce such sharp response between what is allowed and what is not allowed.
58
So you can't really get directly jumped like these.
59
So what ends up happening is more.. the black lines
60
that you see right here those are more realistic filters
61
so the chains or allowing of the high frequencies or the low frequencies is not as abrupt as i indicated in
62
here earlier it's more subtle than that
63
so more realistic filters look like these now what do these things really mean
64
so let's take a quick look at low pass filter what those were was a plot of magnitude response of the filter,
65
meaning it's a plot of magnitude against frequency on the x -axis.
66
The x -axis is the frequency, y -axis is the magnitude.
67
When we are dealing with filters, there is one more plot we're interested in,
68
which is the phase angle of the output changes with respect to the phase angle of the input.
69
So phase angle versus frequency plot is also interesting whenever we're dealing with frequency response,
70
but we'll look at that later on when we discuss specific type of filters.
71
So here is a generic low -pass filter.
72
A couple of points I want to highlight.
73
So this is a plot of the linear magnitude versus linear frequency.
74
Later on we'll see how we can represent a lot longer list of frequencies using something called Bode plots.
75
But for now, linear frequency in the x -axis, linear magnitude in the y -axis, 1 basically means the ratio of the output to the input.
76
Vout over Vin is equal to 1.
77
That means whatever is at the input is being passed towards the output.
78
Okay, this special point right here, 1 over square root 2 in terms of the magnitude has a special function.
79
That is equal to 0 .707.
80
So that's 0 .707.
81
Whatever the magnitude of 0 .707 of the maximum magnitude, so in this case, the maximum magnitude is 1,
82
that particular thing has a special name that's called the cutoff frequency.
83
So cutoff frequency is basically the term understood as frequencies after which the filter does not pass.
84
So that's where the filter cutoff into what passes and what does not pass basically lies.
85
So in this example right here, this abrupt line right here, that was the cutoff frequency.
86
Whereas in a more realistic filter, that would be at 1 square root of 2 of the maximum value.
87
Now in the case of a high -pass filter, this is the cutoff frequency.
88
That's the cutoff frequency.
89
But in a realistic filter, that is the cutoff frequency, 0 .707.
90
In the case of bandpass filter, we have two cutoff frequencies because we have the lower cutoff and the higher cutoff.
91
Same thing in the band stop filter, lower cutoff and higher cutoff.
92
So cutoff frequency basically decide what falls in this region.
93
In the case of the low pass filter, these are the frequencies that pass, and these are the frequencies that do not pass.
94
So that's called a pass band, that's called a stop band.
95
So that is a general idea behind filters.
96
Now, most RLC circuit we're going to look at, RLC circuit, most of them, in fact, all of the circuits that have only R,
97
L, and C components are called passive filters, meaning the output can only be as high as the input.
98
Vout equals Vin is maximum we're going to be able to get.
99
So the ratio of Vout over Vin in these RLC circuits are going to be maximum of 1.
100
Later on, we'll also look at active filters.
101
Active filters employ op -amps in them.
102
When we were dealing with op -amps,
103
we saw that we could use the op -amp and the negative feedback to control the gain of the output, meaning in an op -amp,
104
the output could be higher than the input value.
105
So active filters can have a gain that is greater than one, which is dictated by, again,
106
certain configurations of resistors placed in the feedback path.
107
Well, we'll talk about those later, but for now, we'll basically say that RLC circuits are just RLC -based filters are called passive filters
108
because the maximum gain they have is one, whereas op -amp -based filters are called active filters because the gain can be more than one.
109
In the next video, we'll take a look at some simple RC configuration
110
and look at an RLC configuration and look at low -pass, high -pass, and band -pass filters.
FOR YOU
推荐视频
本课的词汇与口语要点
这节口语课以视频“Frequency Response An Introduction to Filters”为素材。 视频中反复出现的词有:filter, pass, frequency, frequencies, signal。 这段视频共有 110 个句子、1500 个单词可供跟读。 讲话部分时长为 9:27。 说话人语速自然,每分钟约 159 个词,接近日常对话。 只有 77% 的单词属于英语最常用的 3,000 词,词汇难度较高。
视频中的重点词汇
视频中 15 个值得学习的单词,附发音和释义:
| 单词 | 发音 | 释义 |
|---|---|---|
| frequency 名词 | /ˈfɹiːkwənsi/ | 頻率 /频率, 頻度 /频度 |
| filter 名词 | /ˈfɪltɚ/ | 過濾器 /过滤器, 濾過器 /滤过器 |
| input 名词 | /ˈɪnpʊt/ | 輸入 /输入 |
| magnitude 名词 | /ˈmæɡnɪtjuːd/ | 大小 |
| output 名词 | /ˈaʊtpʊt/ | 輸出 /输出 |
| component 名词 | /kəmˈpoʊ.nənt/ | 元件, 部件 |
| realistic 形容词 | /ˌɹɪəˈlɪs.tɪk/ | 現實 /现实, 栩栩如生 |
| axis 名词 | /ˈæksɪs/ | 軸 /轴, 軸心 /轴心 |
| configuration 名词 | /kənˌfɪɡ.əˈɹeɪ̯.ʃən/ | 編排 /编排, 配置 |
| linear 形容词 | /ˈlɪn.i.əɹ/ | 线性 |
| essentially 副词 | /ɪˈsɛnʃəli/ | 本質上 /本质上, 基本上 |
| angle 名词 | /ˈæŋ.ɡəl/ | 角, 角度 |
| whereas | /(h)wɛɹˈæz/ | 然而 |
| connect 动词 | /kəˈnɛkt/ | 連接 /连接 |
| ratio 名词 | /ˈɹeɪ.ʃoʊ/ | 比, 比例 |
视频中出现的短语动词
| 单词 | 发音 | 释义 |
|---|---|---|
| come out 动词 | /ˌkʌm ˈaʊt/ | 出, 出來 /出来 |
| end up 动词 | 到达 | |
| find out 动词 | 找出, 查明 | |
| go through 动词 | 通過 /通过 |
视频中的语法
说话人最常用的结构,并附上视频中的原话:
| 结构 | 视频中的用法 |
|---|---|
| 被动语态 be + 过去分词 — 强调发生了什么,而不是谁做的 | is shown · being multiplied · is called |
| 定语从句 who / which + 从句 — 补充说明人或事物 | filter, which is · one, which is |
需要注意的发音
说话人用了 15 次缩略和弱读形式,例如 we'll, we're, can't。请按听到的简短形式来说。
- “sh” 和 “zh” 音: configuration /kənˌfɪɡ.əˈɹeɪ̯.ʃən/, essentially /ɪˈsɛnʃəli/, ratio /ˈɹeɪ.ʃoʊ/, sharp /ʃɑɹp/
- 长单词——注意重音位置: configuration /kənˌfɪɡ.əˈɹeɪ̯.ʃən/, essentially /ɪˈsɛnʃəli/
中文母语者容易读错的音:
- /v/ — 不要读成 /w/,上齿轻触下唇: versus /ˈvɝsəs/, passive /ˈpæs.ɪv/, vary /ˈvɛəɹi/, voltage /ˈvəʊltɪd͡ʒ/
- 词尾辅音 — 要读清楚,后面不要加元音: circuit /ˈsɝ.kɪt/, bind /ˈbaɪ̯nd/, input /ˈɪnpʊt/, magnitude /ˈmæɡnɪtjuːd/, output /ˈaʊtpʊt/
- /r/ 和 /l/ 的区别: realistic /ˌɹɪəˈlɪs.tɪk/, linear /ˈlɪn.i.əɹ/, alright /ɔlˈɹaɪt/
如何用这段视频练习
- 先完整听一遍视频,不要开口,记下不认识的单词。
- 先用 0.75 倍速逐句跟读,熟练之后再回到正常速度。
- 录下自己的声音并与原声对比,特别注意 frequency, filter, input 这类单词。
什么是跟读法?
跟读法 (Shadowing) 是一种有科学依据的语言学习技巧,最初开发用于专业口译员的培训,并由多语言者Alexander Arguelles博士普及。这个方法简单而强大:您在听英语母语原声的同时立即大声重复——就像是一个延迟1-2秒紧跟说话者的影子。与被动听力或语法练习不同,跟读法强迫您的大脑和口腔肌肉同时处理并模仿真实的讲话模式。研究表明它能显着提高发音准确性,语调,节奏,连读,听力理解和口语流利度——使其成为雅思口语备考和真实英语交流最有效的方法之一。






![[Lecture Ready3] Ch10 Lecture2](https://img.youtube.com/vi/8FVVfebHarQ/mqdefault.jpg)





