Pratica di Shadowing: Frequency Response An Introduction to Filters - Impara a parlare inglese con i video

Scegli una modalità di pratica

Ogni modalità apre una sala di pratica a schermo intero.

110 frasi
Se le frasi sono troppo corte o troppo lunghe, clicca su Edit per modificarle.
1
Alright, let's talk about frequency response and filters.
2
So, frequency response is basically we are going to be looking at circuits and the input circuit,
3
the input to the circuit is going to have more than one frequency or a frequency sweep.
4
So, instead of just a single 60 Hz signal, the input voltage might contain multiple 60 Hz,
5
50 Hz, 120 Hz, 121 Hz and so forth.
6
And we want to find out how the circuit output will respond to an input with such varying frequency.
7
So that's called frequency response.
8
And today the goal is to talk about filters.
9
So what are filters?
10
So consider this.
11
Consider this noisy ECG signal.
12
So here's the ECG signal.
13
You can see the peaks and the valleys, but you do see a lot of noise in that signal.
14
If we put this through a RLC circuit of a particular configuration, and we'll talk about those configurations later on,
15
what we can get is a much cleaner -looking signal from which we can decipher a lot more important information.
16
So we put in a noisy signal into an RLC circuit, what came out was a clean -looking signal.
17
So essentially what a filter is, and exactly as the English word means, it filters out certain unwanted components.
18
And in this case, the unwanted components might have been high -frequency noise.
19
So a filter is essentially an electronic circuit which performs some kind of signal processing function.
20
And specifically, it's intended to remove unwanted signal components,
21
or it's intended to enhance the components of the signal that we want to keep.
22
Now, there are a number of types of filters.
23
There are basically four types low -pass filter, which is shown on the top left right here,
24
allows lower signal frequencies, so frequency starting at DC all the way to some lower value to pass,
25
and anything else beyond that does not pass.
26
So what this is showing is the magnitude, so imagine a signal coming through and is being multiplied by this particular thing, okay?
27
So this is a gain of one, let's say, right at this point, so we'll call this a gain of 1.
28
We'll call this a gain of 1.
29
So any signal that comes in, let's say here's my signal that's coming in, I multiply that.
30
What I essentially have is the frequencies that are beyond, below this point.
31
And by the way, this was the frequency of the input signal.
32
Any frequency that's beyond this passes, anything that at this point does not pass,
33
anything around this point right here does not pass, this right here does not pass.
34
So we have only the lower frequencies passing, so it's called a low -pass filter.
35
The opposite side of this is called a high -pass filter.
36
So the lower frequencies do not go through, meaning the output is equal to zero whenever the frequency of the input is low.
37
All the higher frequencies pass through, so that's called a high -pass filter.
38
A bandpass filter is a filter that allows signals within a band of frequencies, somewhere in the middle.
39
Not the lower frequencies, not the higher frequencies to pass through, but a small band in the middle to pass through.
40
For example, FM station, 91 .1.
41
91 .1 is a particular frequency that is right in between the lower frequencies and the higher frequencies.
42
So when I tune my car radio to 91 .1, I should be getting only MPR.
43
So the lower side does not pass, the higher side does not pass, only 91 .1 passes, so that's called band pass filter.
44
The opposite of band pass filter is called a band stop filter.
45
We want to allow the lower frequencies to pass, higher frequencies to pass, but a smaller band not to pass.
46
Now when we connect AC equipment, because our AC signals are 60 Hz,
47
what we see is on top of whatever it is
48
that we're measuring we might see what is known as a 60 Hertz hum meaning a noise
49
or a 60 Hertz component
50
that is not really a part of the signal it comes in
51
because it's connected to an AC outlet now we want to be able to get rid of
52
that 60 Hertz in
53
that case we would use this band stop filter where we would allow every frequency that's not 60 hertz to pass.
54
On the lower side, any frequency above 60 hertz to pass, but we want to prevent the 60 hertz from passing.
55
So that's called a band stop filter.
56
Now these are all ideal looking filters.
57
No real realistic circuit can produce such sharp response between what is allowed and what is not allowed.
58
So you can't really get directly jumped like these.
59
So what ends up happening is more.. the black lines
60
that you see right here those are more realistic filters
61
so the chains or allowing of the high frequencies or the low frequencies is not as abrupt as i indicated in
62
here earlier it's more subtle than that
63
so more realistic filters look like these now what do these things really mean
64
so let's take a quick look at low pass filter what those were was a plot of magnitude response of the filter,
65
meaning it's a plot of magnitude against frequency on the x -axis.
66
The x -axis is the frequency, y -axis is the magnitude.
67
When we are dealing with filters, there is one more plot we're interested in,
68
which is the phase angle of the output changes with respect to the phase angle of the input.
69
So phase angle versus frequency plot is also interesting whenever we're dealing with frequency response,
70
but we'll look at that later on when we discuss specific type of filters.
71
So here is a generic low -pass filter.
72
A couple of points I want to highlight.
73
So this is a plot of the linear magnitude versus linear frequency.
74
Later on we'll see how we can represent a lot longer list of frequencies using something called Bode plots.
75
But for now, linear frequency in the x -axis, linear magnitude in the y -axis, 1 basically means the ratio of the output to the input.
76
Vout over Vin is equal to 1.
77
That means whatever is at the input is being passed towards the output.
78
Okay, this special point right here, 1 over square root 2 in terms of the magnitude has a special function.
79
That is equal to 0 .707.
80
So that's 0 .707.
81
Whatever the magnitude of 0 .707 of the maximum magnitude, so in this case, the maximum magnitude is 1,
82
that particular thing has a special name that's called the cutoff frequency.
83
So cutoff frequency is basically the term understood as frequencies after which the filter does not pass.
84
So that's where the filter cutoff into what passes and what does not pass basically lies.
85
So in this example right here, this abrupt line right here, that was the cutoff frequency.
86
Whereas in a more realistic filter, that would be at 1 square root of 2 of the maximum value.
87
Now in the case of a high -pass filter, this is the cutoff frequency.
88
That's the cutoff frequency.
89
But in a realistic filter, that is the cutoff frequency, 0 .707.
90
In the case of bandpass filter, we have two cutoff frequencies because we have the lower cutoff and the higher cutoff.
91
Same thing in the band stop filter, lower cutoff and higher cutoff.
92
So cutoff frequency basically decide what falls in this region.
93
In the case of the low pass filter, these are the frequencies that pass, and these are the frequencies that do not pass.
94
So that's called a pass band, that's called a stop band.
95
So that is a general idea behind filters.
96
Now, most RLC circuit we're going to look at, RLC circuit, most of them, in fact, all of the circuits that have only R,
97
L, and C components are called passive filters, meaning the output can only be as high as the input.
98
Vout equals Vin is maximum we're going to be able to get.
99
So the ratio of Vout over Vin in these RLC circuits are going to be maximum of 1.
100
Later on, we'll also look at active filters.
101
Active filters employ op -amps in them.
102
When we were dealing with op -amps,
103
we saw that we could use the op -amp and the negative feedback to control the gain of the output, meaning in an op -amp,
104
the output could be higher than the input value.
105
So active filters can have a gain that is greater than one, which is dictated by, again,
106
certain configurations of resistors placed in the feedback path.
107
Well, we'll talk about those later, but for now, we'll basically say that RLC circuits are just RLC -based filters are called passive filters
108
because the maximum gain they have is one, whereas op -amp -based filters are called active filters because the gain can be more than one.
109
In the next video, we'll take a look at some simple RC configuration
110
and look at an RLC configuration and look at low -pass, high -pass, and band -pass filters.

Scarica l'app

Tutto ciò che serve per parlare fluentemente

Pronuncia con IAVoto per ogni frase
Pratica IPAPadroneggia ogni suono
VocabolarioCostruisci il tuo lessico
Gioco di vocabolarioImpara giocando
FOR YOU

Video consigliato

Vocabolario e note di pronuncia per questa lezione

Questa lezione di conversazione si basa sul video “Frequency Response An Introduction to Filters”. Le parole che ritornano più spesso: filter, pass, frequency, frequencies, signal. Questo video contiene 110 frasi e 1500 parole da ripetere con lo shadowing. Il parlato dura 9:27. Chi parla ha un ritmo naturale di circa 159 parole al minuto, vicino a una conversazione quotidiana. Solo il 77% delle parole rientra nelle 3.000 più comuni dell’inglese, quindi il lessico è impegnativo.

Vocaboli chiave di questo video

15 parole del video che vale la pena imparare, con pronuncia e significato:

ParolaPronunciaSignificato
frequency sostantivo/ˈfɹiːkwənsi/frequenza
filter sostantivo/ˈfɪltɚ/filtro
input sostantivo/ˈɪnpʊt/immissione
magnitude sostantivo/ˈmæɡnɪtjuːd/vastità, magnitudine
output sostantivo/ˈaʊtpʊt/risultato, produzione
component sostantivo/kəmˈpoʊ.nənt/componente
realistic aggettivo/ˌɹɪəˈlɪs.tɪk/realistico
axis sostantivo/ˈæksɪs/asse
configuration sostantivo/kənˌfɪɡ.əˈɹeɪ̯.ʃən/configurazione
linear aggettivo/ˈlɪn.i.əɹ/lineare
essentially avverbio/ɪˈsɛnʃəli/in essenza
angle sostantivo/ˈæŋ.ɡəl/angolo
unwanted aggettivo/ʌnˈwɒntɪd/indesiderato
whereas/(h)wɛɹˈæz/laddove, mentre
connect verbo/kəˈnɛkt/connettere, connettersi

I phrasal verb che sentirai

ParolaSignificato
pass through verbotrapassare
end up verboandare a finire, finire
find out verboscoprire
go through verboattraversare

La grammatica di questo video

Le strutture che chi parla usa di più, con le parole esatte del video:

StrutturaNel video
Forma passiva be + participio passato — conta ciò che accade, non chi lo fais shown · being multiplied · is called
Frasi relative who / which + frase — un’informazione in più su una persona o una cosafilter, which is · one, which is

Pronuncia a cui fare attenzione

Chi parla usa 15 contrazioni e forme ridotte, come we'll, we're, can't. Pronunciale nella forma breve, così come le senti.

  • I suoni “sh” e “zh”: configuration /kənˌfɪɡ.əˈɹeɪ̯.ʃən/, essentially /ɪˈsɛnʃəli/, ratio /ˈɹeɪ.ʃoʊ/, sharp /ʃɑɹp/
  • Parole lunghe — attenzione all’accento: configuration /kənˌfɪɡ.əˈɹeɪ̯.ʃən/, essentially /ɪˈsɛnʃəli/

I suoni difficili per chi parla italiano:

  • /h/ — va soffiata, non è muta: whereas /(h)wɛɹˈæz/, highlight /ˈhaɪˌlaɪt/, enhance /ɪnˈhæns/, hertz /hɝts/
  • Consonante finale — senza aggiungere una vocale dopo: circuit /ˈsɝ.kɪt/, bind /ˈbaɪ̯nd/, input /ˈɪnpʊt/, magnitude /ˈmæɡnɪtjuːd/, output /ˈaʊtpʊt/
  • /æ/ — più aperta della “e”: magnitude /ˈmæɡnɪtjuːd/, axis /ˈæksɪs/, angle /ˈæŋ.ɡəl/, whereas /(h)wɛɹˈæz/, feedback /ˈfiːdˌbæk/

Come esercitarsi con questo video

  1. Ascolta tutto il video una volta senza parlare e annota le parole che non conosci.
  2. Inizia a velocità 0,75×, fai shadowing frase per frase e torna alla velocità normale quando diventa facile.
  3. Registrati e confronta con l’originale, facendo attenzione a parole come frequency, filter, input.

Cos'è la tecnica dello Shadowing?

Shadowing è una tecnica di apprendimento delle lingue supportata da studi scientifici, originariamente sviluppata per la formazione dei traduttori professionisti e resa popolare dal poliglotta Dr. Alexander Arguelles. Il metodo è semplice ma potente: ascolti un audio in inglese di madrelingua e lo ripeti immediatamente ad alta voce — come un'ombra che segue il parlante con un ritardo di solo 1–2 secondi. A differenza dell'ascolto passivo o degli esercizi di grammatica, lo shadowing costringe il tuo cervello e i muscoli della bocca a elaborare e riprodurre simultaneamente i modelli di discorso reale. La ricerca dimostra che migliora significativamente la precisione della pronuncia, l'intonazione, il ritmo, il discorso connesso, la comprensione dell'ascolto e la fluidità del parlato — rendendolo uno dei metodi più efficaci per la preparazione alla prova di speaking dell'IELTS e per la comunicazione reale in inglese.

Tecnica dello shadowing: leggi la guida completa passo dopo passo →