Pratica di Shadowing: PLC Programming Tutorial - Ladder Logic #2: Timers and Counters - Impara a parlare inglese con i video

What's up Automation Nation?

Welcome back to LeMaster Tech and in today's video we're going to continue our tutorial series on ladder diagram basic

Ladder Programming for Automation and Controls Engineering.

Today we're going to be looking at the most common types of timers and counters used in PLC programming.

We're going to look at TONs, which are timer on delay, TOF, which is timer off delay,

TONR, which is often also abbreviated RTO or retentive timer in other platforms.

And then we're also going to look at counters, count up, count down, they're pretty much the same.

So we're going to cover all of these today.

We're going to the syntax is quite different, but the concept is exactly the same.

If you're using these in structured text or another PLC programming language, this is meant as a standalone tutorial.

So the concepts in here don't require prior knowledge of any of the past tutorials,

but we are also compounding automation and controls and ladder programming knowledge as we go through this series.

And as we dive into these tutorials, if you're really enjoying the content, be sure to leave a like on the video, subscribe to the channel.

And if you want to help me grow faster, feel free to check out my Patreon down below as well.

So to start as a reminder, my physical setup, which we kind of covered in the last video,

I have a 24 volt power supply that is powering a Siemens Symatic S7 -1200 PLC.

It's running TIA Portal version 17.

We're covering ladder diagram, not Siemens TIA portal.

So the instructions that we're covering in this video will work for most platforms, but that's what I'm using.

And then for demonstration purposes, I have a control box with two hand switches

and four output lights that are going to be used for the examples in this video.

So if you want to pause on this, my face is probably in the way.

If you want to pause on this wiring schematic and build some similar test bench, go ahead.

that I'm using in the description below the video.

Okay, so let's dive right into it.

I'm gonna go ahead and delete out everything I have in this code.

Okay, so I've got all functional code out of this program.

The only thing we're calling in main is the LadderTutorials binary function, which is what we're programming here, and it has no code in it.

And then if I show all the PLC tags, All I have are my four output tags for my lights and my two input tags for my hand switches.

I added those in the last video if you're curious.

But there's nothing on this PLC, so now let's dive into the timer.

and we're going to drop the empty box function in here, and we're just going to start with a TON.

The T -O -N is...

timer on delay, it is the most common timer.

And honestly, you can do almost everything you need to do in code with this.

So we'll call it example ton.

Let's do EX all caps just some crazy like that.

We're gonna do an example timer on delay here.

Okay, and it's kind of nice.

It populates with the four parameters you need to know about for timers.

There's on what condition do we want this timer to start?

That's this in some platforms will call that EN for enable, some platforms will have IN for input,

but they're sort of universally on what conditions do you want to start the timer?

Now, PT, process timer, preset timer, it doesn't really matter.

That's your set point.

Okay, it's called PT in almost every platform,

but that's your set is going to be something that starts on these input conditions,

counts up to a value, that's your PT, and And then when the timer finishes, that will actuate your output bit,

which is just true, false, has the timer finished.

And that's my cue.

If you remember most European and international standards to avoid O's that look like zeros, call outputs cues.

But like Rockwell Allen Bradley uses an O there.

They just say like, hey, you'll figure it out.

Um, for output, but the Q is going to be what happens when the timer is done.

And then the only other thing we haven't talked about here is this ET, which is our elapsed time.

So as the timer is counting up to that preset time value,

it's continuously keeping track of how much time has passed in the elapsed time field.

So that's everything that makes up a timer object.

And you might have seen when I made this TO and block, it created a database of this example timer.

you have to create a little pocket of memory to store these variables.

There has to be the input bit, the Q bit, the output bit the preset timer and the elapsed timer stored somewhere.

So that's living in a timer database that's called example timer.

So let's say what do we want to have actuate this timer to have it start.

Simplest thing we can do is just say when I turn hand switch one on.

So while hand switch one is on.

And if you missed the previous video on binary conditions, This means that the whole time hand switch one is on, I want the timer counting up.

So not just when I turn it on, which would be like this P, which would be the positive transition of it turning on,

but the whole time hand switch one is on I want this timer counting up.

Now, we're not going to put anything in elapsed time

because it's a purely internal thing that's keeping track of how long the timer has been active.

but we'll put two seconds in preset time.

So we'll say 2000 because the default unit is going to be milliseconds.

But what you see when I hit enter is that it says T pound sign 2S.

Okay, so the Siemens PLC is taking that value, inferring that I meant milliseconds, and it's making it

T pound sign to s

which is the Siemens PLC standard for a time parameter in

like Alan Bradley it's just gonna leave the millisecond value punch in there

if I were to say two and a half seconds if I were to type in 2500 here

It's going to give me this T pound sign two seconds underscore 500 milliseconds.

It's honestly kind of annoying, but you can even delete the S and the underscore and just say T pound sign 2500 milliseconds.

that part doesn't matter too much because if you want, you can always just throw a millisecond value in there and TIA portal generally is going to translate it for you.

Most PLC timers are expecting you to punch in a millisecond value there.

Let's go ahead and change it back to two seconds, 2000 milliseconds.

We're not going to put anything in the elapsed time.

And then we're just going to add when the output finishes, when the timer finishes.

Let's go ahead and turn on output light one.

Okay, so I've got my box here.

I think it looks pretty good last video just keeping it on screen.

Let's download this to the PLC.

We're going to hit these little glasses and play button which is live monitoring.

And every PLC platform generally has some form of live monitoring the logic, so just make sure to hit the button for yours and now we're going to look when i turn on

Hand switch 1, we should see a timer start counting and after 2 seconds the light should turn on.

Okay?

And it's beautiful when it works.

When I turn the hand switch off, it's going to turn off right away.

And what you could see when I turn this on is the timer starts counting.

Maybe you could see the elapsed time value starts counting up there.

So elapsed time is the number on top that's counting up 0, 250 milliseconds, 1 second, 2 seconds until the light turns on.

So that is the basic functionality of a timer on delay is conditions trigger it to start

100

you can use the output bit of that timer to turn on the light.

101

Now, an interesting derivation off of this, but super useful if you want your timers and your commands for your timers in different spots,

102

you can reference this example timer Dot done bit you can reference that bit on a separate line of code.

103

This will work exactly the same way.

104

So in a really large ladder program, you might want to create a timer based on a certain input in one spot.

105

but then use the output of that timer in another spot You can do

106

that with this sort of referencing the timer output elsewhere.

107

So if I turn the hand switch on, you'll see the timer still counts up.

108

The timer done bit will become true and then the output light will still turn on.

109

So you can reference that output light elsewhere.

110

One additional thing to mention while we're here, you can look for a, let's say, greater than block, greater than.

111

And we'll say, get rid of the X timer dot done bit here.

112

We'll say now if X timer...

113

dot elapsed time is greater than one second.

114

And now let's also say, just to get tricky with it, let's say "and the timer's not done." Okay?

115

then we want the light to turn on.

116

This is us looking at the elapsed time and saying, "Okay, the timer's been active for more than one second

117

but hasn't yet finished." That's when we want to turn on the light.

118

So we're creating a program that, if it's working correctly, should turn on when the timer gets to one second, so halfway finished, and then turns off after one second.

119

So let's take a look.

120

OK, that's kind of a cool example of using elapsed time and the done bit, and you kind of get a multi -state output out of that.

121

So that's sort of every component of the basic TON, timer on delay block.

122

Now let's look at TOF, and this is going to go really fast because it's very similar.

123

Okay, so let's go ahead and put this back just as the very simplest version, which was just when the timer finishes, we'll turn output light 1 on.

124

And now we'll start making something that instead is going to look at hand switch 2.

125

Thank you.

126

and here's where it's kinda nice to have the box we can leave all our

127

Previous timers in place and now we're gonna type in T.

128

Oh F.

129

Okay timer off delay and we'll do example Toph okay.

130

Oh F though timer off delay and And similarly, but to show that it's different, we'll make this one 3000.

131

OK, so we'll make this three seconds.

132

it has the exact same in preset time, elapsed time, and cue.

133

It is still a timer block.

134

It has all of the same values, inputs and outputs, and variables as the TON.

135

It's a timer block.

136

The main difference between the TON and the TOF is

137

that this output will become true as soon as the input conditions are true, regardless of how long the preset time is.

138

But they will stay active for a period of time after the input conditions are active, and then go away after that timer.

139

So timer off delay means

140

Outputs energize immediately when the input conditions are true and then the output is retained for a period of time afterwards.

141

So timer off delay.

142

Let's go ahead and send this one that's going to turn on output light to just

143

so you guys can see exactly what that looks like.

144

Okay, so I'm gonna go ahead and trigger output hand switch to.

145

And you can see the light turns on immediately.

146

And now I'm gonna turn hand switch to off.

147

And now you can see the elapsed time starts counting up and three seconds later output light two turns off.

148

So if we were gonna do something like we did a little bit earlier, which was...

149

use the elapsed time so if we do a greater than and we use the elapsed time on our example toff,

150

example toff dot elapsed time, and we say that when it's greater than 1500, Then we want to turn,

151

let's use output light three so we can leave output light two exactly how it is.

152

when the timer, the elapsed timer is greater than 1500, we want output light three to turn on.

153

So let's go ahead and send that.

154

So with that active, You can see the hand switch is not active right now, but output light 3 is on because the elapsed time has hit 3 seconds.

155

So the timer finished and elapsed time has hit 3 seconds.

156

Let's go ahead and cycle hand switch 2 real quick and talk about what's happening.

157

You can see elapsed time goes to zero and then when I turn the hand switch off, it starts counting up it gets above 1500 and then it stays on.

158

So what you would actually want to do in this case is rather than looking for elapsed time greater than 1500 seconds,

159

we'd want to look at it elapsed time less than 1500 seconds.

160

This is what it'll mean when the timer starts counting, which means at the point the input conditions have fallen false, after half of that countdown,

161

that's when the light will turn on.

162

and here you can see both lights turn on at the same time

163

and they're gonna stay on because elapsed time stays zero the whole time the input conditions are true.

164

And then when I trigger it off, you can see the timer starts counting up.

165

When I hit 15 seconds, the red light goes away or maybe you can't because I moved the box out of the way.

166

But you get the idea.

167

The interesting thing here is elapsed time is zero the whole time that timer is energized because it's not counting.

168

true and my elapsed time is zero.

169

And then once the sort of falling edge of the input conditions are detected, the timer starts counting up and that's when elapsed time starts trending towards preset time.

170

And once elapsed time hits preset time, it stays at or just above preset time and output stays false.

171

So TOF is kind of a count for a certain period of time after a condition has Alright,

172

so let's move on from the TOF and look at what could really be considered kind of the third type of timer, the only other kind of timer really, which is a retentive timer.

173

Alright, let's go ahead and this in Siemens is a TONR.

174

In Allen Bradley, it's RTO or retentive timer.

175

So we'll call it Toner example.

176

Thank you.

177

And there's a new bit on this one.

178

There's reset.

179

And that's because retentive timer is counting up while conditions are true, but it's not going to forget that value.

180

So if I have hand switch one true, this ton elapsed time will start counting up.

181

But if I turn hand switch one back off before it reaches the preset time, elapsed time goes back to zero.

182

It resets by default every time turn hand switch 2 off,

183

this timer is going to start counting up and elapsed time is going to start counting up.

184

But if I turn hand switch 2 back on, it's going to forget how long its elapsed time was and just go back to zero.

185

Sometimes, like if you might want over the span of a day, you want to trigger some sort of clean in place or reset cycle every time something has happened,

186

a valve has been opened for a full hour or something like that,

187

you might want to retain a trigger that's like let's say both hand switches being on...

188

No, let's say both hand switches being off are going to be what's actually going to reset the timer.

189

But both hand switches being on will be what triggers the timer, and then the timer being done.

190

Okay, so let me write this and then re explain it a little bit better.

191

It's hard to write code and explain it super well.

192

Um...

193

at the same time.

194

But let's look at how a retentive timer works by using when both hand switches are true.

195

This will count up.

196

Let's give it a higher target value like 10 ,000 milliseconds or 10 seconds.

197

And then we're going to do nothing with elapsed time.

198

We're just going to let it count up and we're going to have this be what triggers output light number four.

199

Okay.

200

And maybe, yeah, we're going to have some of the other lights triggering during this time

201

because I'm not going to delete those timers.

202

But let's talk through what this is saying again real quick.

203

This is saying when hand switch one and hand switch two are both active, count up.

204

And we'll see elapsed time counting up while both of them are active.

205

But if I turn either of those two hand switches off, this is going to remember.

206

It's going to retain the elapsed time so far.

207

And it's going to store that in elapsed time until someone comes along and resets it.

208

And the reset conditions I have are when both hand switches are off.

209

already finished

210

so basically no matter what this timer is going to hold

211

on to how long both hand switches have been active until it hits 10 seconds

212

and then I can turn both hand switches off to get it to reset let's go ahead

213

and download this and see it in practice okay so

214

Output light 4 is this one that my index finger's on right here.

215

I'm just going to keep the index finger on so you guys don't lose it amidst the other timers we already made.

216

And I turn one hand switch on, the timer's not counting up yet.

217

I turn the second hand switch on, it starts counting up, it gets to 3 seconds, and I turn one of the hand switches off.

218

And you can see just above the timer block, it's holding on to 3 seconds and 441 milliseconds.

219

Now I'm going to turn both of them back on.

220

And I'm going to turn the other hand switch off this time.

221

And you can see I got to 6 .7 seconds, but it remembers how long it was active.

222

Now I turn them both on.

223

and I'm going to let it get up to 10 seconds.

224

And now you can see it's done and output light four turned on.

225

And I'm going to turn one hand switch off.

226

That didn't reset it.

227

I'm going to turn the other hand switch off

228

that didn't reset it because my conditions to reset are both hand switches being off and the timer done.

229

So now if I turn both hand switches off, you see output light four turns off.

230

Okay, so a retentive timer is sort of like I was describing, useful for the total amount of time something was active being true.

231

If you have a heating jacket or a cooling jacket and the total heating time is the thing that matters,

232

but it could start and stop and start and stop numerous times during a batch, but you need to make sure that something is mixing for a minimum of one hour or something like that.

233

A retentive timer can be a really useful tool.

234

and delete all three of these networks and showcase one more thing that is closely related to these.

235

So I think it's super useful to cover here.

236

And I'm going to delete all these networks and we're going to do a counter.

237

Okay.

238

So a counter is not necessarily a timer

239

because you're counting up just total conditions and the number of times a condition has been met, but it's not time bound.

240

So for example, let's go ahead and say I want to count by using the positive rising edge of hand switch one.

241

I want to count the number of times I've cycled hand switch one

242

and I don't care how long it was on

243

or off in between cycles just total number of times that HandSwitch 1 has been turned on.

244

I need to make a memory bit so that I can remember the last state of HandSwitch 1.

245

We covered this in the last video.

246

If you haven't seen a rising edge like one shot trigger before, not a bad idea to go check out the Boolean logic video.

247

But basically, if I want to say, how do I keep track of the total number of times that hand switch one has turned on?

248

I want this instruction called CTU, count up.

249

Other types of counters are count down and then a CTUD, which is count up and down.

250

But we're just going to cover count up because similar to TON, TOF and RTO or TONR, they're all iterations on a theme.

251

So if we cover count up, you should have a pretty good idea what you're doing here.

252

say, let's make a counter example data block.

253

And you're going to see count up, which is actually the trigger to count something.

254

And then we see the reset bit, just like the retentive timer.

255

We see PV, which is the preset value.

256

And in this case, let's say we want this counter to be done when we get to 10 cycles.

257

OK, so 10 times oscillating that hand switch on.

258

And then when this is finished, let's just go ahead and turn all of the lights on.

259

OK, so let's just use all the lights for a cool light show.

260

And we'll say output light two, three, and four are all going to turn on when this counter finishes.

261

All right.

262

And now let's add to the reset condition.

263

What we want to have turn it off.

264

And we'll say, how about the rising edge of hand switch 2 is what's going to reset this.

265

um and let's go ahead and make a hand switch to memory bit just like we did for hand switch one

266

Boolean global memory.

267

Global memory is easier so I don't have to stick it in a database.

268

And let's go ahead and say

269

that I only want the rising edge of hand switch 2 to reset my counter if the counter has also finished, okay? So...

270

This one, totally optional.

271

You don't have to.

272

Add this bit for this to work.

273

It would work just by looking at hand switch to

274

but I'm gonna say I don't want to reset this counter

275

unless it's finished no matter what I want to keep track of how many times this has occurred.

276

So let's go ahead and download this and view it in practice.

277

Okay, so let's get our box up here.

278

Let's look at hand switch one right here and let's start cycling it.

279

Alright, I turn it on, there's the positive edge, and you can see the value of my counter turned to 1.

280

I turn it back off.

281

Doing hand switch 2 does nothing because the counter hasn't finished.

282

But now if I get to 2, three, four five, six, seven eight Nine.

283

Okay, the next high transition of this hand switch is going to complete the counter

284

because you can see it got to its target value.

285

Now it's at 10 and all four of the lights turned on.

286

What's cool about the count up block is it's actually going to keep counting even though it's already finished.

287

So you can use counters to just track total number of times something has happened

288

and not worry too much about that PV value where you're like,

289

curious how often this valve is cycling or things like that.

290

You can use a counter just to track number of strokes.

291

Okay, but now let's say even with hand switch one in the true position, which is obviously the signal to count up.

292

If I make hand switch two now, Oh, it's not going to reset it because I used the wrong bit.

293

Rather than using done, I used count up, which is a trigger...

294

that is not going to be helpful.

295

So we're going to use "QU"

296

which means "Output Count Up has finished." I used "Count Up"

297

which is only true for one cycle when the rising edge of hand switch one is true.

298

PLCs are fast enough that there's no way I was going to get that to work.

299

So this is the output bit saying count up is true

300

and you can see it's already highlighted green because we're well above the set point of 10.

301

So I'm going to go ahead and trigger...

302

hand switch to on again Where's the box?

303

There it is.

304

And you can see all my lights turn off.

305

OK, so count up is very similar to a timer, but it's not time bound.

306

It's sort of conditional bound, but it's super useful to include timers in counters.

307

OK, so I know these are action packed tutorials.

308

It's impossible to cover any of these instructions in every possible use case.

309

But I think we're building a really excellent skill set and fundamental understanding of ladder as we go through these.

310

I hope you found this useful.

311

Drop in the comments any questions that you might have and what you'd like to see next on the channel.

312

I hope you've been finding them useful.

313

If you really love the channel, consider leaving a like on the video, subscribing to the channel.

314

My Patreon is down below.

315

And as always, thank you for watching and see you next time.

📺 Stesso Canale

Types of Proximity Sensors! #automation #engineering #science #robotics #electronics

Business EnglishUniversity StudentsWorking Adults

Adding an E-Stop to our Conveyor Build! #plc #automation #engineering #robotics #mechatronics

Business EnglishUniversity StudentsWorking Adults

✨ Video consigliato

109 frasi

Tonex Plug Headphone Amp | First Impressions and Review

Business EnglishUniversity StudentsWorking Adults

64 frasi

What is SCADA?

Business EnglishUniversity StudentsWorking Adults

238 frasi

Wiring Allen Bradley Compactlogix Sinking Inputs and Sourcing Outputs

Business EnglishUniversity StudentsWorking Adults

155 frasi

Every Hardware Protocol Explained Simply in 10 Minutes!

Business EnglishUniversity StudentsWorking Adults

333 frasi

Master n8n Triggers in 20 Minutes – Automate Anything

Business EnglishUniversity StudentsWorking Adults

245 frasi

Intro To TTrades Fractal Model [Indicator & Settings]

Business EnglishUniversity StudentsWorking Adults

236 frasi

The 7 Quality Control (QC) Tools Explained with an Example!

Business EnglishUniversity StudentsWorking Adults

309 frasi

Claude Code: The Advanced Guide (99% of Devs Skip These Features)

Business EnglishUniversity StudentsWorking Adults

423 frasi

Free CCNA | VLANs (Part 2) | Day 17 | CCNA 200-301 Complete Course

Business EnglishUniversity StudentsWorking Adults

24 frasi

Sofeast PCB Video Series Introduction

Business EnglishUniversity StudentsWorking Adults

Cos'è la tecnica dello Shadowing?

Shadowing è una tecnica di apprendimento delle lingue supportata da studi scientifici, originariamente sviluppata per la formazione dei traduttori professionisti e resa popolare dal poliglotta Dr. Alexander Arguelles. Il metodo è semplice ma potente: ascolti un audio in inglese di madrelingua e lo ripeti immediatamente ad alta voce — come un'ombra che segue il parlante con un ritardo di solo 1–2 secondi. A differenza dell'ascolto passivo o degli esercizi di grammatica, lo shadowing costringe il tuo cervello e i muscoli della bocca a elaborare e riprodurre simultaneamente i modelli di discorso reale. La ricerca dimostra che migliora significativamente la precisione della pronuncia, l'intonazione, il ritmo, il discorso connesso, la comprensione dell'ascolto e la fluidità del parlato — rendendolo uno dei metodi più efficaci per la preparazione alla prova di speaking dell'IELTS e per la comunicazione reale in inglese.

Tecnica dello shadowing: leggi la guida completa passo dopo passo →

Pratica di Shadowing: PLC Programming Tutorial - Ladder Logic #2: Timers and Counters - Impara a parlare inglese con i video

Types of Proximity Sensors! #automation #engineering #science #robotics #electronics

PLC Programming #4: Functions, Function Blocks & Organization Blocks Explained

Going Online with a PLC, Uploading and Downloading Code!

PLC Programming Tutorial - Ladder Logic #3: Math and Calculations

What is a PLC and how does it work?

How to Scale Analog Values in PLC Programming!

PLC Programming Tutorial - Ladder Logic #1: Binary & Boolean Operations

PLC Programming #5: User-Defined Data Types (UDTs) Explained

How to Get Started with C# in Visual Studio Code! Full Tutorial for Beginners

PLC State Machines Explained

Adding an E-Stop to our Conveyor Build! #plc #automation #engineering #robotics #mechatronics

Tonex Plug Headphone Amp | First Impressions and Review

What is SCADA?

Wiring Allen Bradley Compactlogix Sinking Inputs and Sourcing Outputs

Every Hardware Protocol Explained Simply in 10 Minutes!

Master n8n Triggers in 20 Minutes – Automate Anything

Intro To TTrades Fractal Model [Indicator & Settings]

The 7 Quality Control (QC) Tools Explained with an Example!

Claude Code: The Advanced Guide (99% of Devs Skip These Features)

Free CCNA | VLANs (Part 2) | Day 17 | CCNA 200-301 Complete Course

Sofeast PCB Video Series Introduction

Perché praticare il parlato con questo video?

Grammatica & Espressioni nel Contesto

Trappole di Pronuncia Comuni

Cos'è la tecnica dello Shadowing?