쉐도잉 연습: How Electric Motors Work - 3 phase AC induction motors ac motor - 영상으로 영어 말하기 배우기

연습 모드 선택

각 모드는 전체 화면 연습실로 열립니다.

161 문장

문장이 너무 짧거나 길면 Edit를 눌러 조정하세요.

This is an electrical motor is one of the most important

devices ever to be invented these motors are used everywhere from pumping the water we drink to powering elevators

and cranes even cooling nuclear power stations

so we are going to look inside one

and learn in detail exactly how they work in this video

which is sponsored by the Great Courses Plus visit the link in the video description to start a free trial

and get access to some truly great online courses.

The induction motor will look something like this.

They turn electrical energy into mechanical energy which we can use to drive pumps,

fans, compressors, gears, pulleys etc. Almost all the parts are held inside the main housing.

At the front we find the shaft.

This is the part that rotates and we can connect things like pumps, gears and pulleys to this to do work for us.

At the back we find the fan and a protective cover.

The fan is connected to the shaft and so it rotates whenever the motor operates.

That's because the induction motor can produce a lot of heat

when in operation so the fan blows ambient air over the casing to cool it down.

If the induction motor became too hot

The insulation of the internal electrical coils will melt.

This will cause a short circuit and the motor will destroy itself.

The fins on the side of the enclosure help to increase the surface area and that lets us remove more unwanted heat.

The shaft is supported by some bearings, which sit inside the front as well as the rear shields.

The bearings help the shaft rotate smoothly and also hold it in position.

Inside the housing we find the stator.

The stator is stationary and does not rotate.

This consists of a number of copper wires which are wrapped into coils between the slots positioned around the inner perimeter.

The copper wires are coated with a special enamel which electrically insulates the wires from each other.

This means electricity has to flow through the entire coil.

Otherwise it would take the shortest path possible and we'll see why that's important a little later in this video.

Now, this is a three phase induction motor, so we have three separated sets of coils in the stator.

The ends of each set will connect with the terminals within the electrical terminal box.

We will also see how these are connected a little later in this video.

When connected to the electrical supply, the stator generates a rotating electromagnetic field.

Connected to the shaft is the rotor.

In this case, it's a squirrel cage type rotor.

It's called a squirrel cage because it has two end rings which are connected by some bars

and these will all rotate together.

This design is similar to a small cage or an exercise wheel used by a pet hamster or even a squirrel.

The squirrel cage is fitted with a number of laminated steel sheets.

These sheets will help concentrate the magnetic field into the bars.

Sheets are used instead of a solid piece of metal as

this improves the efficiency by reducing the size of the eddy currents in the rotor.

When the rotor is placed inside the stator and the stator is connected to an electrical power supply, the rotor will begin to rotate.

So how does this work?

work.

When electricity passes through a wire an electromagnetic field is generated around the wire.

We can see this by placing some compasses around the wire.

The compasses will rotate to align with this magnetic field.

If the direction of current is reversed the magnetic field also reverses and so the compasses will change direction.

The magnetic field of the wire is pulling

and pushing the compass dials just like

if we slide two bar magnets towards each other they will either be attracted or repelled.

We can even use one magnet to rotate another

or we could also rotate the magnet by changing the intensity of the magnetic field around it.

If we place a wire in a magnetic field

and pass a current through it the magnetic field of the wire will interact with the permanent magnets magnetic field

and the wire will therefore experience a force this force will move the wire either upwards or downwards

depending on the direction of current and the polarity of the magnetic fields.

If we wrap the wire into a coil, the electromagnetic field becomes stronger.

The coil will produce a north and south pole just like a permanent magnet.

We call these coils of wire an inductor.

When we pass an alternating current through the wire, the electrons will be constantly changing direction between flowing forwards

and backwards so the magnetic field will also expand and collapse and the polarity reverses each time.

When we place another separated coil in close proximity and complete the circuit,

the electromagnetic field will induce a current in the second coil.

We can connect two coils together and place them opposite each other to create a larger magnetic field field.

If we placed a closed loop of wire inside

this large magnetic field we will induce a current in the loop as we know

when we pass a current through a wire it generates a magnetic field

and we also know the magnetic fields will push or pull each other when they interact.

So this loop of wire will also generate a magnetic field and this will interact with the larger magnetic field.

Each side of the coil will experience opposing forces which causes it to rotate.

This loop is therefore our rotor and the coils are therefore our stator.

The rotor will only rotate until it aligns with the stator coils.

At this point it will likely get stuck as the induced current reverses with the coil.

To overcome this we need to introduce another set of coils in the stator and we must connect these to another phase.

The electrons flow in this phase at a slightly different time.

So the electromagnetic field will also therefore change in strength as well as polarity at a slightly different time.

This will force the rotor to rotate.

Inside the induction motor we have three separated coils which are used to produce a rotational electromagnetic field.

When we pass an alternating current through each coil,

the coils will produce an electromagnetic field which changes in intensity as well as polarity as the electrons change direction.

But if we were to connect each coil to a different phase, then the electrons in each coil will change direction at a different time.

This means the polarity and intensity of the magnetic field will also occur at a different time.

To distribute this magnetic field we need to rotate the coil sets 120 degrees from the previous phase.

We then combine these into the stator.

The magnetic field varies in strength and polarity between the coils which combine to produce the effect of a rotating magnetic field.

We saw earlier in this video that current can be induced into a second coil when in close proximity.

The bars of the squirrel cage are shorted at each end, which therefore creates multiple loops or coils.

Each bar therefore induces a current and creates a magnetic field.

The magnetic field of the rotor bars interacts with the magnetic field of the stator.

The rotor bar's magnetic field is attracted to the magnetic field of the stator.

As the magnetic field is rotating,

the rotor will therefore also rotate in the same direction as the magnetic field to try and align with it,

but it will never be able to fully catch up.

The bars of the rotor are often skewed.

This helps distribute the magnetic field across multiple bars and stops the motor being able to align and jam.

the stator contains all of the coils

or windings used to create the rotating electromagnetic field

when electricity is passed through the wires to power the coils we find an electrical terminal box on the top

100

or sometimes on the side inside this box we have six electrical terminals each terminal has a corresponding letter

101

and number we have u1 v1 and w1 then w2 u2

102

and v2 we have our phase 1 coil connected to the 2u terminals then the phase 2 coils

103

which are connected to the 2v terminals and lastly the phase 3 coil

104

which is connected to the 2w terminals notice

105

that the electrical terminals are arranged in a different configuration on one side to the other.

106

We will see why that is in just a moment.

107

We now bring in our three phase power supply and connect these to their respective terminals.

108

For the motor to run, we need to complete the circuit.

109

And there are two ways to do this.

110

The first way is the Delta configuration.

111

For this, we connect across the terminals U1 to W2, V1 to U2, and W1 to V2.

112

This will give us our delta configuration.

113

Now, when we provide AC current through the phases, we see

114

that electricity flows from one phase to another as the direction of AC power reverses in each phase at a different time.

115

That is why we have the terminals in different arrangements in the terminal box.

116

Because we can easily connect across and allow electricity to flow between the phases as the electrons reverse at different times.

117

The other way we can connect the terminals is to use the star or Y configuration.

118

In this method, we connect between W2, U2 and V2 on only one side.

119

This will give us our star or Y equivalent connection.

120

Now, when we pass electricity through the phases, we see the electrons are shared between the terminals of the phases.

121

Due to their design differences, the amount of current flowing in the star and delta configuration is very different.

122

And we're going to see some calculations for these towards the end of this video.

123

But first, I want to tell you about The Great Courses Plus.

124

All of our viewers can get a free trial right now by visiting thegreatcoursesplus .com forward slash engineering mindset.

125

The Great Courses Plus is an on -demand learning platform that lets you binge -watch lectures and courses.

126

They have over 13 ,000 videos by industry experts on everything from science, maths, history, and even cooking.

127

Personally, my favorite is their engineering lectures and their course on inventions that change the world.

128

As a fan of this channel, I'm certain you'll also find these interesting too, so do check those out.

129

They add new content every month and you can watch as many videos as you want from your TV, tablet, laptop or phone.

130

Just click the link in the video description down below to start your free trial today.

131

Let's have a look at the difference between the star and delta configurations.

132

Let's say we have the motor connected in delta with a supply voltage of 400 volts.

133

That means when we use a multimeter to measure the voltage between any two phases, we will get a reading of 400 volts.

134

We call this our line -to -line voltage.

135

Now, if we measure across the two ends of a coil, we again see the line -to -line voltage of 400 volts.

136

Let's say each coil has a resistance, or impedance as this is alternating current, of 20 ohms.

137

That means we will get a current reading on the coil of 20 amps.

138

We can calculate that from 400 volts divided by 20 ohms, which is 20 amps.

139

But the current in the line will be different.

140

It will be 34 .6 amps.

141

We get that from 20 amps multiplied by the square root of 3, which is 34 .6 amps.

142

That's because each phase is connected to two coils.

143

Now, if we look at the star or wire configuration, we again have a line -to -line voltage of 400 volts.

144

We see that if we measure between any two phases, but with the star configuration,

145

all our coils are connected together and meet at the star point or neutral point.

146

It's from this point that we can run a neutral wire if needed.

147

So this time, when we measure the voltage across the ends of any coil we get a lower voltage of 230 volts.

148

That's because the phase isn't directly connected to two coils like in the delta configuration.

149

One end of the coil is connected to a phase

150

but the other is connected to a shared point so the voltage is therefore shared.

151

The voltage is less as one phase is always in reverse.

152

We can calculate this by 400 volts divided by the square root of three, which is 230 volts.

153

As the voltage is less, the current will be two.

154

If this coil also has an impedance of 20 ohms, then 230 volts divided by 20 amps I'll see you guys equals 11 .5 amps.

155

The line current will also therefore be the same at 11 .5 amps.

156

So we can see from the Delta configuration the coil is exposed to the full 400 volts between two phases.

157

But the star configuration is only exposed to 230 volts between the phase and the neutral point.

158

So the star uses less voltage and less current compared to the Delta version.

159

Okay, that's it for this video, but to continue learning about electrical engineering,

160

check out one of the videos on screen now and I'll catch you there for the next lesson.

161

Don't forget to follow us on Facebook, Instagram, LinkedIn, as well as theengineeringmindset .com.

앱 다운로드

유창하게 말하는 데 필요한 모든 것

AI 발음 평가문장마다 점수 확인

IPA 발음 연습모든 소리 마스터

단어 학습나만의 단어장 만들기

단어 게임놀면서 외우기

QR 스캔

Download on theApp Store Get it onGoogle Play

같은 채널

FOR YOU

이 레슨의 어휘와 말하기 포인트

이 말하기 레슨은 영상 “How Electric Motors Work - 3 phase AC induction motors ac motor”을(를) 바탕으로 합니다. 가장 자주 반복되는 단어는 다음과 같습니다: coil, field, magnetic, phase, wire. 이 영상에는 섀도잉할 문장 161개와 단어 2253개가 있습니다. 말하는 구간의 길이는 15:29입니다. 화자는 분당 약 145단어의 일정한 속도로 말해서 섀도잉하기에 편한 속도입니다. 영어에서 가장 많이 쓰이는 3,000단어에 속하는 단어가 75%뿐이라 어휘가 어려운 편입니다.

이 영상의 핵심 어휘

영상에 나오는 익혀 둘 만한 단어 15개를 발음, 뜻과 함께 정리했습니다.

단어	발음	뜻
magnetic 형용사	/mæɡˈnɛtɪk/	자석의
connect 동사	/kəˈnɛkt/	잇다, 연결하다
wire 명사	/ˈwaɪɚ/	철사
terminal 명사	/ˈtɚmɪnəl/	터미널, 공항 터미널
voltage 명사	/ˈvəʊltɪd͡ʒ/	전압
delta 명사	/ˈdɛltə/	델타
electromagnetic 형용사	/ɪˌlɛk.tɹoʊ.mæɡˈnɛ.tɪk/	전자기의
loop 명사	/luːp/	고리
cage 명사	/keɪd͡ʒ/	우리
magnet 명사	/ˈmæɡ.nɪt/	자석
squirrel 명사	/ˈskwɪ.ɹ(ə)l/	다람쥐
compass 명사	/ˈkʌmpəs/	나침반, 라침반
sheet 명사	/ʃit/	장, 시트
pump 명사	/pʌmp/	펌프
neutral 형용사	/ˈnuː.tɹəl/	중립의

이 영상의 문법

화자가 가장 많이 쓰는 문형을 영상 속 실제 표현과 함께 정리했습니다.

문형	영상 속 표현
수동태 be + 과거분사 — 누가 하는지보다 무슨 일이 일어나는지에 초점	be invented · is sponsored · are held
관계절 who / which + 절 — 사람이나 사물에 대한 추가 정보	wires which are · rings which are · coils which are

주의할 발음

화자는 I'll, don't, I'm 같은 축약형과 약화된 형태를 8번 사용합니다. 들리는 대로 짧게 발음하세요.

“th” 소리: mathematics /mæθ(.ə)ˈmæt.ɪks/, smoothly /ˈsmuːðli/
“sh”와 “zh” 소리: configuration /kənˌfɪɡ.əˈɹeɪ̯.ʃən/, shaft /ˈʃɑːft/, induction /ɪnˈdʌkʃən/, sheet /ʃit/, efficiency /ɪˈfɪʃ.ən.si/
긴 단어 — 강세 위치에 주의: configuration /kənˌfɪɡ.əˈɹeɪ̯.ʃən/, electrical /ɪˈlɛktɹɪkəl/, electromagnetic /ɪˌlɛk.tɹoʊ.mæɡˈnɛ.tɪk/, electricity /ɪˌlɛkˈtɹɪsɪti/, intensity /ɪnˈtɛnsɪti/

한국어 화자가 어려워하는 소리:

/f/ — ㅍ(/p/)으로 바꾸지 말고 윗니를 아랫입술에 대기: configuration /kənˌfɪɡ.əˈɹeɪ̯.ʃən/, shaft /ˈʃɑːft/, efficiency /ɪˈfɪʃ.ən.si/, fin /fɪn/
/v/ — ㅂ(/b/)과 구별하기: voltage /ˈvəʊltɪd͡ʒ/, reverse /ɹɪˈvɝs/, divide /dɪˈvaɪd/, overcome /ˌəʊ.vəˈkʌm/, vary /ˈvɛəɹi/
/z/ — ㅈ이 아니라 성대를 울리는 /s/: expose /ɪkˈspoʊz/, oppose /əˈpoʊz/, upwards /ˈʌpwɚdz/, downwards /ˈdaʊnwɚdz/

이 영상으로 연습하는 방법

먼저 말하지 않고 영상을 끝까지 듣고 모르는 단어를 적어 둡니다.
보통 속도로 한 문장씩 섀도잉하고, 화자의 리듬과 맞을 때까지 반복합니다.
자신의 목소리를 녹음해 원본과 비교하고, magnetic, connect, wire 같은 단어에 특히 주의합니다.

쉐도잉이란? 영어 실력을 빠르게 키우는 과학적 방법

쉐도잉(Shadowing)은 원래 전문 통역사 훈련을 위해 개발된 언어 학습 기법으로, 다언어 학자인 Dr. Alexander Arguelles에 의해 대중화된 방법입니다. 핵심 원리는 간단하지만 매우 강력합니다: 원어민의 영어를 들으면서 1~2초의 짧은 지연으로 즉시 소리 내어 따라 말하는 것——마치 '그림자(shadow)'처럼 화자를 따라가는 것입니다. 문법 공부나 수동적인 청취와 달리, 쉐도잉은 뇌와 입 근육이 동시에 실시간으로 영어를 처리하고 재현하도록 훈련합니다. 연구에 따르면 이 방법은 발음 정확도, 억양, 리듬, 연음, 청취력, 말하기 유창성을 크게 향상시킵니다. IELTS 스피킹 준비와 자연스러운 영어 소통을 원하는 분들에게 특히 효과적입니다.

섀도잉 방법: 단계별 전체 가이드 읽기 →

쉐도잉 연습: How Electric Motors Work - 3 phase AC induction motors ac motor - 영상으로 영어 말하기 배우기

연습 모드 선택

앱 다운로드

같은 채널

Ohms Law Explained - The basics circuit theory

Single Phase Electricity Explained - wiring diagram energy meter

Air Conditioning System Basics hvacr how does it work

120V 240V Electricity explained - Split phase 3 wire electrician

How ELECTRICITY works - working principle

Diodes Explained - The basics how diodes work working principle pn junction

Centrifugal Pump Basics - How centrifugal pumps work working principle hvacr

추천 영상

How does a Steam Turbine Work?

Types of Proximity Sensors! #automation #engineering #science #robotics #electronics

An Animated Introduction to Vibration Analysis by Mobius Institute

I Made an EMP Device... It Actually Works

How a Car Engine Works

3-D Brain Scans | Pathways 2

Metabolism | Electron Transport Chain: DETAILED | Part 1

How I use AI to learn engineering (anti brain rot studying)

This Machine Keeps Ship Engines Alive | Fuel Oil Purifier Explained

26 - How does harmonic phase shifting work including a detailed mathematical explanation to reduce s

Current | Introduction to electrical engineering | Electrical engineering | Khan Academy