쉐도잉 연습: Air Conditioning System Basics hvacr how does it work - 영상으로 영어 말하기 배우기
레슨 만드는 중...
1
sponsored by danfoss when we look at a typical refrigeration system we have the compressor
2
the condenser the expansion valve and the evaporator the condenser
3
and the evaporator are both heat exchangers the condenser sits outside the property
4
and the evaporator sits inside the room being cooled the compressor circulates a refrigerant in the pipe work
5
which cycles between all of these components the expansion valve regulates
6
the flow of refrigerant the refrigerant is a specially designed fluid
7
which can change between being a liquid and a gas very easily and that's
8
because it has a very low boiling point for example refrigerant
9
are for 10 a will boil at negative 48 degrees Celsius
10
or negative 55 degrees Fahrenheit although this will change with pressure
11
but if the refrigerant is inside a pipe within a room
12
and the room is at 30 degrees Celsius
13
or 86 degrees Fahrenheit then this will be more than enough to cause it to boil from a liquid into a vapor.
14
By the way if you want some refrigerant charts you can download these for free from our website.
15
I'll link to these in the video description down below.
16
So the The refrigerant is entering the evaporator as a low pressure, low temperature liquid vapor mixture.
17
It flows on the inside of the pipe
18
and at the same time a fan is moving the ambient air of the room over the outside of the pipe.
19
This causes the refrigerant to boil.
20
It will absorb the heat from the air through the pipe wall and then it evaporates.
21
As the refrigerant evaporates, it carries away the heat.
22
It's similar to when we boiled water.
23
The water heats up, it evaporates and turns into steam and carries this heat away.
24
So the air on the outside is entering hot and it's leaving cold.
25
The refrigerant continues to travel through the evaporator, picking up more heat which boils it further until it becomes slightly superheated.
26
This basically means it's now completely gas and doesn't contain any droplets of liquid refrigerant.
27
Liquid damages the compressor, so we want to ensure it can't reach the compressor.
28
The compressor sucks in the refrigerant, which is leaving the evaporator as a low -pressure, low -temperature, slightly superheated vapour.
29
It then squeezes this together into a much smaller space, and so the pressure increases.
30
All the heat which was picked up in the evaporator is now contained in a much smaller volume, so the temperature will increase.
31
This is very important and we will see why in just a moment.
32
But if you've ever pumped up a bicycle tyre, you will notice the pump becomes hotter as it's compressing the air.
33
The refrigerant is then pushed into the condenser where it enters as a high -pressure, high -temperature, superheated vapour.
34
the condenser is located outside
35
and the outside air might be very warm on a summer's
36
day as heat always flows from hot to cold we need to ensure
37
that the refrigerant is hotter than the outside air otherwise the
38
unwanted heat will not be able to leave the refrigerant and leave our system
39
a fan will help to blow ambient air over the condenser to remove this heat
40
so the outside air is entering warm picking up heat
41
and leaving hot as the heat is removed by the air
42
this causes the refrigerant to condense back into a liquid it's a little bit like
43
when steam hits the window on a cold day the window is cold
44
so it condenses the steam from a vapor into a liquid
45
and then this liquid starts to run down the window the
46
refrigerant therefore exits as a high pressure medium temperature saturated liquid
47
and this heads to the expansion valve the expansion valve needs
48
to regulate the amount of refrigerant entering the evaporator to control the superheat
49
if it allows too much refrigerant to flow it can flood the evaporator
50
so the refrigerant doesn't evaporate a liquid reaches the compressor
51
and possibly destroys it but
52
if it lets in too little refrigerant the system won't provide enough cooling and
53
so it operates inefficiently the expansion valve regulates the refrigerant by
54
only allowing it to pass through a small hole this creates
55
a large pressure difference across the valve one side is the high -pressure liquid the other side is almost empty
56
The small hole causes it to almost spray into the evaporator as a part liquid, part vapor mixture.
57
The refrigerant will expand to try and fill the empty space on the other side
58
and this will cause it to drop in pressure as well as temperature.
59
It's a little bit like spraying a deodorant can or a spray paint can.
60
It flows through a small hole causing it to expand as a part vapor
61
and part liquid mixture
62
and then we can feel the can become cooler now the
63
original method to control this was by using a fixed orifice device
64
and you might still find these on the back of your
65
refrigerators the hole within this device was a fixed size
66
so the entire system would simply turn on
67
and off to meet the cooling demand it does work
68
but we can't maintain a stable temperature control
69
because the system is simply turning on
70
and off the next evolution was the thermostatic expansion valve this is still widely used today
71
and it senses the superheat at the outlet through a bulb
72
which is filled with another refrigerant this other refrigerant will expand to close the valve
73
when the superheat is too high and it condenses to open the valve when the superheat is too low.
74
This type of valve needs to be manually calculated and adjusted by a technician.
75
It does work very well but it's prone to mistakes.
76
It also takes a long time to calculate and set up
77
and it is also only adjusted once per service visit which is not ideal.
78
It will also not allow peak performance.
79
However it does work very well and these will continue to be used for many years.
80
And And so the latest evolution is to use electronic expansion valves.
81
These use a controller to measure the exact temperature and pressure
82
and adjust the valve position automatically in real time to ensure optimal performance and maximum system efficiency.
83
Okay that's it for this video but to continue learning about HVAC
84
and refrigeration engineering click on one of the videos on screen now and I'll catch you there for the next lesson.
85
Don't forget to follow us on Facebook, Twitter, LinkedIn, Instagram as well as theengineeringmindset .com
📺 같은 채널
B21
How ELECTRICITY works - working principle
Business EnglishUniversity StudentsWorking Adults
C11
Diodes Explained - The basics how diodes work working principle pn junction
Business EnglishUniversity StudentsWorking Adults
C1Centrifugal Pump Basics - How centrifugal pumps work working principle hvacr
Business EnglishUniversity StudentsWorking Adults
✨ 추천 영상
B21
23 문장
Working Principle of Chiller Plant | Animation | English
Business EnglishUniversity StudentsWorking Adults
C12
40 문장
Inside the Relay Controlled SF6 Circuit Breaker: Preventing Arcs and Ensuring Safety
Business EnglishUniversity StudentsWorking Adults
C11
176 문장
Every Networking Concept Explained | Networking 101 (2026)
Business EnglishUniversity StudentsWorking Adults
B21
234 문장
Your House Is Making You Sick (15 Solutions)
Business EnglishUniversity StudentsWorking Adults
C11
166 문장
What's The Best Supercharger? Roots vs Centrifugal vs Twin-Screw vs Electric
Business EnglishUniversity StudentsWorking Adults
C194 문장
Transient Thermal Analysis in ANSYS AIM
Business EnglishUniversity StudentsWorking Adults
C11
254 문장
REVIT 2023 FOR MEP - SYSTEM PIPING
Business EnglishUniversity StudentsWorking Adults
C11
339 문장
Introduction to HPLC - Lecture 1: HPLC Basics
Business EnglishUniversity StudentsWorking Adults
C11
64 문장
What is SCADA?
Business EnglishUniversity StudentsWorking Adults
C17
60 문장
What is SMT (Surface Mount Technology)? PCB Assembly (Part 2)
Business EnglishUniversity StudentsWorking Adults
C11
50 문장
0.0.1 How to become a CAE Engineer CAE | What are the ways to become a CAE Engineer as a fresher
Business EnglishUniversity StudentsWorking Adults
이 레슨의 어휘와 말하기 포인트
이 말하기 레슨은 영상 “Air Conditioning System Basics hvacr how does it work”을(를) 바탕으로 합니다. 가장 자주 반복되는 단어는 다음과 같습니다: refrigerant, liquid, valve, heat, evaporator. 이 영상에는 섀도잉할 문장 85개와 단어 1097개가 있습니다. 말하는 구간의 길이는 7:15입니다. 화자는 분당 약 151단어로, 일상 대화에 가까운 자연스러운 속도로 말합니다. 영어에서 가장 많이 쓰이는 3,000단어에 속하는 단어가 77%뿐이라 어휘가 어려운 편입니다.
이 영상의 핵심 어휘
영상에 나오는 익혀 둘 만한 단어 15개를 발음, 뜻과 함께 정리했습니다.
| 단어 | 발음 | 뜻 |
|---|---|---|
| liquid 명사 | /ˈlɪk.wɪd/ | 액체 |
| valve 명사 | /ˈvælv/ | 밸브 |
| boil 동사 | /bɔɪ(ə)l/ | 비등하다, 끓다 |
| pipe 명사 | /ˈpaɪp/ | 피리 |
| vapor 명사 | /ˈveɪpɚ/ | 증기 |
| expand 동사 | /ɪkˈspænd/ | 펴다, 피다 |
| spray 명사 | /spɹeɪ/ | 스프레이 |
| regulate 동사 | /ˈɹɛɡ.jə.leɪt/ | 규정하다 |
| pump 명사 | /pʌmp/ | 펌프 |
| calculate 동사 | /ˈkælkjʊleɪt/ | 정산하다, 계산하다 |
| stable 명사 | /ˈsteɪ.bəl/ | 마구간, 축사 |
| chart 명사 | /t͡ʃɑɹt/ | 차트, 도표 |
| lesson 명사 | /ˈlɛs.ən/ | 수업, 과 |
| ideal 형용사 | /aɪˈdi(ə)l/ | 이상적, 리상적 |
| suck 동사 | /sʌk/ | 빨다 |
영상에 나오는 구동사
| 단어 | 뜻 |
|---|---|
| pick up 동사 | 줍다 |
이 영상의 문법
화자가 가장 많이 쓰는 문형을 영상 속 실제 표현과 함께 정리했습니다.
| 문형 | 영상 속 표현 |
|---|---|
| 수동태 be + 과거분사 — 누가 하는지보다 무슨 일이 일어나는지에 초점 | being cooled · was picked · is located |
| 관계절 who / which + 절 — 사람이나 사물에 대한 추가 정보 | refrigerant, which is · heat which was · visit which is |
주의할 발음
화자는 can't, doesn't, I'll 같은 축약형과 약화된 형태를 9번 사용합니다. 들리는 대로 짧게 발음하세요.
- “sh”와 “zh” 소리: evolution /ˌiːvəˈluːʃ(ə)n/, efficiency /ɪˈfɪʃ.ən.si/, specially /ˈspɛʃəli/, technician /tɛkˈnɪʃən/
- 긴 단어 — 강세 위치에 주의: evolution /ˌiːvəˈluːʃ(ə)n/, efficiency /ɪˈfɪʃ.ən.si/, manually /ˈmænj(u)əliː/, refrigerator /ɹɪˈfɹɪd͡ʒ.əˌɹeɪ.tɚ/, evaporator /ɪˈvæp.ə.ɹeɪt.ɚ/
한국어 화자가 어려워하는 소리:
- /f/ — ㅍ(/p/)으로 바꾸지 말고 윗니를 아랫입술에 대기: efficiency /ɪˈfɪʃ.ən.si/, flood /flʌd/, fluid /ˈflu.ɪd/, refrigerator /ɹɪˈfɹɪd͡ʒ.əˌɹeɪ.tɚ/
- /v/ — ㅂ(/b/)과 구별하기: valve /ˈvælv/, vapor /ˈveɪpɚ/, evolution /ˌiːvəˈluːʃ(ə)n/, evaporator /ɪˈvæp.ə.ɹeɪt.ɚ/, evaporate /ɪˈvæp.ə.ɹeɪt/
- /z/ — ㅈ이 아니라 성대를 울리는 /s/: exit /ˈɛɡzət/, squeeze /skwiːz/
이 영상으로 연습하는 방법
- 먼저 말하지 않고 영상을 끝까지 듣고 모르는 단어를 적어 둡니다.
- 0.75배속으로 한 문장씩 섀도잉을 시작하고, 익숙해지면 보통 속도로 돌아갑니다.
- 자신의 목소리를 녹음해 원본과 비교하고, liquid, valve, boil 같은 단어에 특히 주의합니다.
쉐도잉이란? 영어 실력을 빠르게 키우는 과학적 방법
쉐도잉(Shadowing)은 원래 전문 통역사 훈련을 위해 개발된 언어 학습 기법으로, 다언어 학자인 Dr. Alexander Arguelles에 의해 대중화된 방법입니다. 핵심 원리는 간단하지만 매우 강력합니다: 원어민의 영어를 들으면서 1~2초의 짧은 지연으로 즉시 소리 내어 따라 말하는 것——마치 '그림자(shadow)'처럼 화자를 따라가는 것입니다. 문법 공부나 수동적인 청취와 달리, 쉐도잉은 뇌와 입 근육이 동시에 실시간으로 영어를 처리하고 재현하도록 훈련합니다. 연구에 따르면 이 방법은 발음 정확도, 억양, 리듬, 연음, 청취력, 말하기 유창성을 크게 향상시킵니다. IELTS 스피킹 준비와 자연스러운 영어 소통을 원하는 분들에게 특히 효과적입니다.