शैडोइंग अभ्यास: Air Conditioning System Basics hvacr how does it work - वीडियो के साथ अंग्रेजी बोलना सीखें
पाठ बनाया जा रहा है...
1
sponsored by danfoss when we look at a typical refrigeration system we have the compressor
2
the condenser the expansion valve and the evaporator the condenser
3
and the evaporator are both heat exchangers the condenser sits outside the property
4
and the evaporator sits inside the room being cooled the compressor circulates a refrigerant in the pipe work
5
which cycles between all of these components the expansion valve regulates
6
the flow of refrigerant the refrigerant is a specially designed fluid
7
which can change between being a liquid and a gas very easily and that's
8
because it has a very low boiling point for example refrigerant
9
are for 10 a will boil at negative 48 degrees Celsius
10
or negative 55 degrees Fahrenheit although this will change with pressure
11
but if the refrigerant is inside a pipe within a room
12
and the room is at 30 degrees Celsius
13
or 86 degrees Fahrenheit then this will be more than enough to cause it to boil from a liquid into a vapor.
14
By the way if you want some refrigerant charts you can download these for free from our website.
15
I'll link to these in the video description down below.
16
So the The refrigerant is entering the evaporator as a low pressure, low temperature liquid vapor mixture.
17
It flows on the inside of the pipe
18
and at the same time a fan is moving the ambient air of the room over the outside of the pipe.
19
This causes the refrigerant to boil.
20
It will absorb the heat from the air through the pipe wall and then it evaporates.
21
As the refrigerant evaporates, it carries away the heat.
22
It's similar to when we boiled water.
23
The water heats up, it evaporates and turns into steam and carries this heat away.
24
So the air on the outside is entering hot and it's leaving cold.
25
The refrigerant continues to travel through the evaporator, picking up more heat which boils it further until it becomes slightly superheated.
26
This basically means it's now completely gas and doesn't contain any droplets of liquid refrigerant.
27
Liquid damages the compressor, so we want to ensure it can't reach the compressor.
28
The compressor sucks in the refrigerant, which is leaving the evaporator as a low -pressure, low -temperature, slightly superheated vapour.
29
It then squeezes this together into a much smaller space, and so the pressure increases.
30
All the heat which was picked up in the evaporator is now contained in a much smaller volume, so the temperature will increase.
31
This is very important and we will see why in just a moment.
32
But if you've ever pumped up a bicycle tyre, you will notice the pump becomes hotter as it's compressing the air.
33
The refrigerant is then pushed into the condenser where it enters as a high -pressure, high -temperature, superheated vapour.
34
the condenser is located outside
35
and the outside air might be very warm on a summer's
36
day as heat always flows from hot to cold we need to ensure
37
that the refrigerant is hotter than the outside air otherwise the
38
unwanted heat will not be able to leave the refrigerant and leave our system
39
a fan will help to blow ambient air over the condenser to remove this heat
40
so the outside air is entering warm picking up heat
41
and leaving hot as the heat is removed by the air
42
this causes the refrigerant to condense back into a liquid it's a little bit like
43
when steam hits the window on a cold day the window is cold
44
so it condenses the steam from a vapor into a liquid
45
and then this liquid starts to run down the window the
46
refrigerant therefore exits as a high pressure medium temperature saturated liquid
47
and this heads to the expansion valve the expansion valve needs
48
to regulate the amount of refrigerant entering the evaporator to control the superheat
49
if it allows too much refrigerant to flow it can flood the evaporator
50
so the refrigerant doesn't evaporate a liquid reaches the compressor
51
and possibly destroys it but
52
if it lets in too little refrigerant the system won't provide enough cooling and
53
so it operates inefficiently the expansion valve regulates the refrigerant by
54
only allowing it to pass through a small hole this creates
55
a large pressure difference across the valve one side is the high -pressure liquid the other side is almost empty
56
The small hole causes it to almost spray into the evaporator as a part liquid, part vapor mixture.
57
The refrigerant will expand to try and fill the empty space on the other side
58
and this will cause it to drop in pressure as well as temperature.
59
It's a little bit like spraying a deodorant can or a spray paint can.
60
It flows through a small hole causing it to expand as a part vapor
61
and part liquid mixture
62
and then we can feel the can become cooler now the
63
original method to control this was by using a fixed orifice device
64
and you might still find these on the back of your
65
refrigerators the hole within this device was a fixed size
66
so the entire system would simply turn on
67
and off to meet the cooling demand it does work
68
but we can't maintain a stable temperature control
69
because the system is simply turning on
70
and off the next evolution was the thermostatic expansion valve this is still widely used today
71
and it senses the superheat at the outlet through a bulb
72
which is filled with another refrigerant this other refrigerant will expand to close the valve
73
when the superheat is too high and it condenses to open the valve when the superheat is too low.
74
This type of valve needs to be manually calculated and adjusted by a technician.
75
It does work very well but it's prone to mistakes.
76
It also takes a long time to calculate and set up
77
and it is also only adjusted once per service visit which is not ideal.
78
It will also not allow peak performance.
79
However it does work very well and these will continue to be used for many years.
80
And And so the latest evolution is to use electronic expansion valves.
81
These use a controller to measure the exact temperature and pressure
82
and adjust the valve position automatically in real time to ensure optimal performance and maximum system efficiency.
83
Okay that's it for this video but to continue learning about HVAC
84
and refrigeration engineering click on one of the videos on screen now and I'll catch you there for the next lesson.
85
Don't forget to follow us on Facebook, Twitter, LinkedIn, Instagram as well as theengineeringmindset .com
📺 उसी चैनल से
B21
How ELECTRICITY works - working principle
Business EnglishUniversity StudentsWorking Adults
C11
Diodes Explained - The basics how diodes work working principle pn junction
Business EnglishUniversity StudentsWorking Adults
C1Centrifugal Pump Basics - How centrifugal pumps work working principle hvacr
Business EnglishUniversity StudentsWorking Adults
✨ अनुशंसित वीडियो
B21
23 वाक्य
Working Principle of Chiller Plant | Animation | English
Business EnglishUniversity StudentsWorking Adults
C12
40 वाक्य
Inside the Relay Controlled SF6 Circuit Breaker: Preventing Arcs and Ensuring Safety
Business EnglishUniversity StudentsWorking Adults
C11
176 वाक्य
Every Networking Concept Explained | Networking 101 (2026)
Business EnglishUniversity StudentsWorking Adults
B21
234 वाक्य
Your House Is Making You Sick (15 Solutions)
Business EnglishUniversity StudentsWorking Adults
C11
166 वाक्य
What's The Best Supercharger? Roots vs Centrifugal vs Twin-Screw vs Electric
Business EnglishUniversity StudentsWorking Adults
C194 वाक्य
Transient Thermal Analysis in ANSYS AIM
Business EnglishUniversity StudentsWorking Adults
C11
254 वाक्य
REVIT 2023 FOR MEP - SYSTEM PIPING
Business EnglishUniversity StudentsWorking Adults
C11
339 वाक्य
Introduction to HPLC - Lecture 1: HPLC Basics
Business EnglishUniversity StudentsWorking Adults
C11
64 वाक्य
What is SCADA?
Business EnglishUniversity StudentsWorking Adults
C17
60 वाक्य
What is SMT (Surface Mount Technology)? PCB Assembly (Part 2)
Business EnglishUniversity StudentsWorking Adults
C11
50 वाक्य
0.0.1 How to become a CAE Engineer CAE | What are the ways to become a CAE Engineer as a fresher
Business EnglishUniversity StudentsWorking Adults
इस पाठ की शब्दावली और बोलने के सुझाव
यह स्पीकिंग पाठ वीडियो “Air Conditioning System Basics hvacr how does it work” पर आधारित है। सबसे ज़्यादा दोहराए गए शब्द ये हैं: refrigerant, liquid, valve, heat, evaporator। इस वीडियो में शैडोइंग के लिए 85 वाक्य और 1097 शब्द हैं। बोला गया हिस्सा 7:15 लंबा है। वक्ता लगभग 151 शब्द प्रति मिनट की स्वाभाविक गति से बोलता है, जो रोज़मर्रा की बातचीत के करीब है। केवल 77% शब्द अंग्रेज़ी के 3,000 सबसे आम शब्दों में से हैं, इसलिए शब्दावली कठिन है।
इस वीडियो की मुख्य शब्दावली
वीडियो के 15 सीखने लायक शब्द, उच्चारण और अर्थ के साथ:
| शब्द | उच्चारण | अर्थ |
|---|---|---|
| liquid संज्ञा | /ˈlɪk.wɪd/ | द्रव, तरल |
| valve संज्ञा | /ˈvælv/ | वाल्व |
| boil क्रिया | /bɔɪ(ə)l/ | उबलना |
| vapor संज्ञा | /ˈveɪpɚ/ | भाप, भभका |
| mixture संज्ञा | /ˈmɪkst͡ʃɚ/ | मिलाना |
| evolution संज्ञा | /ˌiːvəˈluːʃ(ə)n/ | क्रमविकास |
| pump संज्ञा | /pʌmp/ | पंप, पम्प |
| calculate क्रिया | /ˈkælkjʊleɪt/ | गणना करना, हिसाब रखना |
| stable संज्ञा | /ˈsteɪ.bəl/ | गोष्ठ, अश्वालय |
| chart संज्ञा | /t͡ʃɑɹt/ | लेखाचित्र, चार्ट |
| lesson संज्ञा | /ˈlɛs.ən/ | पाठ, सबक़ |
| ideal विशेषण | /aɪˈdi(ə)l/ | आदर्श, श्रेष्ठ |
| suck क्रिया | /sʌk/ | चूसना |
| exit संज्ञा | /ˈɛɡzət/ | प्रस्थान, निकासी |
| flood संज्ञा | /flʌd/ | बाढ़, सैलाब |
वीडियो में आने वाली फ़्रेज़ल वर्ब
| शब्द | अर्थ |
|---|---|
| pick up क्रिया | उठाना |
इस वीडियो का व्याकरण
वक्ता जिन संरचनाओं का सबसे अधिक प्रयोग करता है, वीडियो के असली शब्दों के साथ:
| संरचना | वीडियो में |
|---|---|
| Passive voice be + past participle — ज़ोर इस पर कि क्या होता है, न कि कौन करता है | being cooled · was picked · is located |
| Relative clauses who / which + उपवाक्य — व्यक्ति या वस्तु के बारे में अतिरिक्त जानकारी | refrigerant, which is · heat which was · visit which is |
ध्यान देने योग्य उच्चारण
वक्ता 9 बार संक्षिप्त रूपों का प्रयोग करता है, जैसे can't, doesn't, I'll। इन्हें वैसे ही छोटा बोलें जैसा आप सुनते हैं।
- “sh” और “zh” की ध्वनियाँ: evolution /ˌiːvəˈluːʃ(ə)n/, efficiency /ɪˈfɪʃ.ən.si/, specially /ˈspɛʃəli/, technician /tɛkˈnɪʃən/
- लंबे शब्द — बलाघात सही रखें: evolution /ˌiːvəˈluːʃ(ə)n/, efficiency /ɪˈfɪʃ.ən.si/, manually /ˈmænj(u)əliː/, refrigerator /ɹɪˈfɹɪd͡ʒ.əˌɹeɪ.tɚ/, evaporator /ɪˈvæp.ə.ɹeɪt.ɚ/
हिंदी भाषियों के लिए मुश्किल ध्वनियाँ:
- /v/ और /w/ का फ़र्क़ — /v/ में ऊपर के दाँत निचले होंठ को छूते हैं, /w/ में होंठ गोल होते हैं: liquid /ˈlɪk.wɪd/, valve /ˈvælv/, vapor /ˈveɪpɚ/, evolution /ˌiːvəˈluːʃ(ə)n/, squeeze /skwiːz/
- /z/ — इसे “ज” (/dʒ/) न बनाएँ: exit /ˈɛɡzət/, squeeze /skwiːz/
- शब्द की शुरुआत में s + व्यंजन — पहले “इ” न जोड़ें: spray /spɹeɪ/, stable /ˈsteɪ.bəl/, sponsor /ˈspɒn.səː/, specially /ˈspɛʃəli/, squeeze /skwiːz/
इस वीडियो से अभ्यास कैसे करें
- पहले बिना बोले पूरा वीडियो एक बार सुनें और जो शब्द नहीं आते उन्हें लिख लें।
- 0.75× गति से शुरू करें, एक-एक वाक्य की शैडोइंग करें, और सहज लगने पर सामान्य गति पर लौटें।
- अपनी आवाज़ रिकॉर्ड करें और मूल से तुलना करें, ख़ासकर liquid, valve, boil जैसे शब्दों पर ध्यान दें।
शैडोइंग तकनीक क्या है?
शैडोइंग (Shadowing) एक विज्ञान-समर्थित भाषा सीखने की तकनीक है जो मूल रूप से पेशेवर दुभाषिया प्रशिक्षण के लिए विकसित की गई थी। विधि सरल लेकिन शक्तिशाली है: आप मूल अंग्रेज़ी ऑडियो सुनते हैं और तुरंत इसे ज़ोर से दोहराते हैं — जैसे वक्ता की छाया 1-2 सेकंड की देरी से। शोध से पता चलता है कि यह उच्चारण सटीकता, स्वर, लय, जुड़ी हुई ध्वनियाँ, सुनने की समझ और बोलने की प्रवाहशीलता में काफ़ी सुधार करता है।