Shadowing Practice: BAS Bootcamp: Day 6 Setting up IO Internally - Learn English Speaking with Video

Bir pratik modu seçin

Her mod tam ekran bir pratik odası açar.

114 cümleler

Cümleler çok kısa veya çok uzun ise, ayarlamak için Düzenle'ye tıklayın.

All righty folks, Phil Zito here and welcome to day six of the BAS Bootcamp.

So what we're going to be looking at in today's video

is we're going to talk about the internal setup of inputs and outputs.

And then in tomorrow's video, we're going to start to look at the external setup of inputs and outputs.

So I mentioned in earlier videos of this BAS Bootcamp series

that you will often go and have these things called universal inputs.

And these universal inputs will allow you to go about setting your inputs

and outputs to do whatever they are capable of processing.

So let's take a look at what that might look like.

So I'm going to add a hardware input and I'm going to add a hardware output.

So right now I'm using DysTech GFX software, and we're going to take a look at setting up one of their inputs.

So we would go to the input, and we would see that right here, and this is how they set it up, and different software is going to look a little different.

But how they set it up is you'll have the name of the hardware input, and then it'll show signal disconnected disconnected.

Now this is a universal input so it's going to give me multiple different types of inputs I can process.

When we're looking at inputs we're really focused on those four input types that I talked about right?

The digital input also known as dry contact, the resistive input these are typically used for temperature,

or the linear input which is what we're typically going to use

if we're doing some form of voltage either volts DC or milliamps of current.

Let's take a look first at digital input because it's definitely the easiest.

So oftentimes when you're setting up a digital input the things you need to know are just just a handful of things.

First off you typically will have some form of action or polarity it'll be called something to to that effect.

And you need to pick, basically what you're saying is, is when this input is electrically, I was gonna say electronically,

but when it's electrically true, meaning it is actually true,

it's actually got the contacts are closed or it's energized, whatever is causing this digital input to be true,

when that's true in the program, it's going to represent a true or a one or some sort of true Boolean value.

If you don't want that to be the case, which is in some cases like when you're doing safeties

and you've got them wired to a specific output or a specific contact type.

Maybe you're using normally closed contacts, and you want those contacts to break to indicate failure.

Then you would actually click this reverse action and or the polarity button,

whatever your software has, and that would go and cause it to turn true when the input was actually false.

Also, on some controllers, you can go and set up their enumeration sets basically it's their data typesets.

All right, so let's then look at a different type of signal.

Let's look at RTDs.

Now, when it comes to RTDs and thermistors, you actually have these things called resistance tables.

So let me see if I can pull up one while I'm talking.

10k type 2 table.

okay and what this will look like i don't know how well this is gonna show up

but uh we'll see so basically what we can see right here is

that for certain degrees fahrenheit there are certain ohm resistance

because remember resistance is measured in ohms we learned

that in yesterday's video or last week's video rather day five

so we see that there's this chart and what happens inside the controller

when you pick the thermistor type like platinum 1000 ohm nickel 1000 ohm 10k type 2

what happens is there's actually a chart that this controller knows

and based on the resistance

that is sensed it is going to calculate temperature now what

you can do is a couple different things Not every controls line has this,

but typically they will have an offset for temperature.

You see this is delta degrees Fahrenheit because we're in degrees Fahrenheit.

So what would happen is as the test and balance went through

and they tested the sensors and they gave you the sensed value versus what you're seeing, you would actually put in a correction factor.

Sometimes you can also put in ohm correction factors.

I do not recommend doing this because that totally screws up your table.

I typically recommend just putting in an output offset.

So setting the actual offset right here for the actual sensed value.

All right.

So that's RTDs and thermistors.

Pretty straightforward also.

So, so far we've covered digital and we've covered RTD and thermistor.

Now, linear is something I see a lot of folks get really tripped up on.

They do have a resistance because sometimes you will be using a potentiometer to go and calculate a specific output,

but we're not going to go through that because that's less common.

What we're going to talk about really is 0 to 10 volts and 0 to 20 milliamps.

So 0 to 10 volts right here is we've got 0 to 10, and then our output is 0 to 100.

Now, this could be for a humidity sensor, in which case it would be 0 to 100.

This could be for a pressure sensor in

which it may be like 0 to 5 or 0 to 20 pounds per square.

It could be a variety of things that you're sensing.

And the important thing here to know when you're dealing with linear is what are my min and max signals?

So 0 to 10 or maybe it's 2 to 10, whatever it is.

and then what does that correspond to from an output perspective?

And it'll do all the calculations itself.

The same for the actual 4 to 20 milliamps, or 0 to 20 milliamps.

So if we wanted to do 4 to 20 milliamps, we'd do like this, right?

4 is 0, so that would actually give us a negative value at 0.

So here we go, and this is how we get this all set up.

Pretty straightforward to set this up.

I do mention though that with some controls, they give you the ability to set COV.

And you see the COV increment is set to 1 here, which is fine here.

But if we went to 0 to 5 volts and we were doing 0 to 5 inches for our actual pressure sensing,

maybe this was building static pressure, and we had 1 as our COV increment, that would not be good.

because change by one in pressure is significant.

So if this may be called COV increment, this may be called refresh rate, this may be called change rate, whatever.

Figure that out.

You want to do anywhere from like one to 5% of the actual throttle range or sensor span.

Sorry, not throttle range.

I started to get into, I've been thinking about PID loops lately.

So sensor span, your sensor span is the effective span of the sensor that is controlled.

So your sensor may actually have a broader range.

It may go to a negative value.

But your controlled range is just this 0 to 5.

Actually, I would argue it's like half to 2.5 is your controlled range.

But, you know, that's just semantics.

So you pick your controlled range.

In our case, we have 5, right?

So we would say, what is 1% of 5?

And it'd be 0, 5.

And so that's what we would refresh.

That would be our refresh rate.

100

These are all kind of really important things to know, and they're what trip up a lot of newer techs.

101

It's not terribly difficult.

102

On the output side, pretty much the same thing, right?

103

We have digital outputs, can configure those, can pick our data types.

104

we have our 0 to 10 volt outputs we can pick

105

that and it has a reverse action that's basically just like polarity

106

and then you know we can have 4 to 20 milliamp I didn't talk really about pulse

107

because I mean outside of monitoring metering and things like

108

that it's not something we use a whole bunch

109

so I hope this was helpful to you and I hope

110

that this really helped you start to figure out how to do inputs

111

and outputs and if you have any questions do Do not hesitate to go below the video and ask those.

112

Tomorrow we will start to look at how do you wire these things up.

113

Thanks a ton.

114

Take care.

Uygulamayı İndir

Akıcı konuşmak için ihtiyacınız olan her şey

AI TelaffuzHer cümleyi puanla

IPA AlıştırmasıHer sesi ustalaştır

Kelime BilgisiKelime bankanızı oluşturun

Kelime OyunuOynarken öğrenin

QR Tara

Download on theApp Store Get it onGoogle Play

Aynı Kanal

BAS Bootcamp: Day 1 BAS 101

Business EnglishUniversity StudentsWorking Adults

FOR YOU

Video Öner

238 cümleler

Bu dersin kelimeleri ve konuşma notları

Bu C1 seviyesindeki konuşma dersi “BAS Bootcamp: Day 6 Setting up IO Internally” videosuna dayanıyor. En çok tekrarlanan kelimeler: input, output, sensor, type, milliamp. Bu videoda gölgeleme çalışması için 114 cümle ve 1420 kelime var. Konuşma bölümü 9:26 sürüyor. Konuşmacı dakikada yaklaşık 151 kelimeyle, günlük konuşmaya yakın doğal bir hızda konuşuyor. Kelimelerin %83’i İngilizcede en sık kullanılan 3.000 kelime arasında; geri kalanına başlamadan önce bakmakta fayda var.

Bu videodaki önemli kelimeler

Videodaki en ileri düzey 15 kelime, telaffuzu ve anlamıyla:

Kelime	Telaffuz	Anlam
sensor isim	/ˈsɛn.sɚ/	duyarga, sensör
volt isim	/vəʊlt/	volt
increment isim	/ˈɪŋkɹɪmn̩t/	artım, artış
throttle isim	/ˈθɹɔ.tl̩/	gaz
calculate fiil	/ˈkælkjʊleɪt/	hesaplamak
correction isim	/kəˈɹɛkʃən/	düzeltme
configure fiil	/kənˈfɪɡə(ɹ)/	yapılandırmak
semantics isim	/sɪˈmæntɪks/	anlambilim
calculation isim	/ˌkælkjuˈleɪʃn̩/	hesaplama
hesitate fiil	/ˈhɛz.ə.teɪt/	çekinmek, kararsız kalmak
nickel isim	/ˈnɪk.əl/	nikel
humidity isim	/hjuːˈmɪd.ə.ti/	nem
voltage isim	/ˈvəʊltɪd͡ʒ/	gerilim
platinum isim	/ˈplæt.ɪn.əm/	platin
pulse isim	/pʌls/	nabız

Duyacağınız deyimsel fiiller

Kelime	Anlam
figure out fiil	açığa çıkarmak
show up fiil	ortaya çıkmak

Bu videodaki dil bilgisi

Konuşmacının en çok kullandığı yapılar, videodaki sözcüklerin aynısıyla:

Yapı	Videoda
Edilgen yapı be + fiilin üçüncü hâli — kimin yaptığı değil, ne olduğu önemli	are typically used · be called · are closed
İlgi cümlecikleri who / which + cümle — bir kişi ya da şey hakkında ek bilgi	input which is · case, which is · here, which is

Dikkat edilecek telaffuzlar

Konuşmacı we're, you're, I'm gibi kısaltılmış biçimleri 40 kez kullanıyor. Bunları duyduğunuz gibi kısa söyleyin.

“sh” ve “zh” sesleri: refresh /ɹɪˈfɹɛʃ/, correction /kəˈɹɛkʃən/, enumeration /ɪˌnjuːməˈɹeɪʃən/, potentiometer /pəˌtɛn(t)ʃiˈɑmɪtəɹ/, calculation /ˌkælkjuˈleɪʃn̩/
Uzun kelimeler — vurguyu doğru yere koyun: polarity /pəˈlæɹɪti/, electrically /ɪˈlɛk.tɹɪk.li/, electronically /ˌɛl.ɛkˈtɹɒn.ɪk.li/, enumeration /ɪˌnjuːməˈɹeɪʃən/, potentiometer /pəˌtɛn(t)ʃiˈɑmɪtəɹ/

Türkçe konuşanların zorlandığı sesler:

Kelime başındaki ünsüz kümesi — araya ünlü eklemeyin: throttle /ˈθɹɔ.tl̩/, straightforward /ˌstɹeɪtˈfɔː(ɹ)wə(ɹ)d/, humidity /hjuːˈmɪd.ə.ti/, platinum /ˈplæt.ɪn.əm/, static /ˈstæt.ɪk/
/æ/ — “e”den daha açık: polarity /pəˈlæɹɪti/, calculate /ˈkælkjʊleɪt/, semantics /sɪˈmæntɪks/, calculation /ˌkælkjuˈleɪʃn̩/, platinum /ˈplæt.ɪn.əm/

Bu videoyla nasıl çalışılır

Videonun tamamını konuşmadan bir kez dinleyin ve bilmediğiniz kelimeleri not edin.
0,75× hızla başlayın, cümle cümle tekrar edin ve kolaylaşınca normal hıza dönün.
Kendinizi kaydedin ve orijinaliyle karşılaştırın; sensor, volt, increment gibi kelimelere özellikle dikkat edin.

Gölgeleme Tekniği Nedir?

Gölgeleme, başlangıçta profesyonel tercüman eğitimi için geliştirilen ve çok dilli Dr. Alexander Arguelles tarafından popüler hale getirilen, bilim destekli bir dil öğrenme tekniğidir. Yöntem basit ama güçlüdür: ana dili İngilizce olan bir sesi dinler ve hemen yüksek sesle tekrar edersiniz — konuşmacıyı 1-2 saniye gecikmeyle takip eden bir gölge gibi. Pasif dinleme veya dilbilgisi alıştırmalarının aksine, gölgeleme beyninizi ve ağız kaslarınızı gerçek konuşma kalıplarını eşzamanlı olarak işlemeye ve yeniden üretmeye zorlar. Araştırmalar, telaffuz doğruluğu, tonlama, ritim, bağlı konuşma, dinleme anlama ve konuşma akıcılığını önemli ölçüde geliştirdiğini göstermektedir — bu da onu IELTS Konuşma hazırlığı ve gerçek dünya İngilizce iletişimi için en etkili yöntemlerden biri yapar.

Shadowing tekniği: adım adım eksiksiz rehberi okuyun →

Shadowing Practice: BAS Bootcamp: Day 6 Setting up IO Internally - Learn English Speaking with Video

Bir pratik modu seçin

Uygulamayı İndir

BAS Bootcamp: Day 1 BAS 101

Wiring Allen Bradley Compactlogix Sinking Inputs and Sourcing Outputs

How F1 Cars Collect Data in Real Time

Understand Microsoft Entra ID | AZ-104 | Episode 2

EDFR GWO BTT Training Center - Nicolas Riou Wind

The Ultimate IoT Roadmap in 2026? | Embedded Systems & IoT Career Roadmap

Your AI broke the layout. Now what?

Transient Thermal Analysis in ANSYS AIM

Helpdesk to Sysadmin - 3 Things You Must Learn First

What is SCADA?

Arturia MiniLab 37 mk3 & Memory V: First Look

How To Read A Datasheet - Electronics with Becky Stern | DigiKey

BGP Overview