शैडोइंग अभ्यास: Wiring Allen Bradley Compactlogix Sinking Inputs and Sourcing Outputs - वीडियो के साथ अंग्रेजी बोलना सीखें
अभ्यास मोड चुनें
हर मोड पूरी स्क्रीन का अभ्यास कक्ष खोलता है।
238 वाक्य
यदि वाक्य बहुत छोटे या लंबे हों, तो समायोजित करने के लिए Edit पर क्लिक करें।
1
- Hi, this is Tim.
2
Today, we're gonna talk about how to wire an Allen -Bradley CompactLogix PLC, both its inputs and outputs.
3
And really this video is for an Allen -Bradley CompactLogix PLC, but these principles work with any Allen -Bradley PLC, or well, really any PLC,
4
or really probably any electrical circuit.
5
Let's stick with NPLC.
6
And we're gonna be following our wiring enough to get started exercise using this wire diagram, which I'll put a link to in the description.
7
I'm also gonna put a link to a video I did on syncing and sourcing inputs.
8
which is critical for figuring out how to wire, not just an Allen Bradley compact logics PLC, but any PLC really.
9
And we go through this basic diagram and determine whether our PLC inputs are sourcing or syncing, and that determines how we wire them.
10
So make sure you watch this video, because this is, this is a very important video.
11
In the case of our compact logics, its PLC inputs are syncing and its PLC outputs are sourcing. So...
12
We plug in our PLC input down at syncing.
13
That means we'll be using sourcing sensors and this tells us how we need to wire it.
14
In the case of the PLC outputs We plug in that we have a source and PLC output, and that means our lights need to be wired for syncing.
15
We're going to go through all of it in this video and we're going to go really slow
16
just to make sure we understand why we're doing what.
17
And so what we're going to start with is we're going to start with our input.
18
We have our DC plus power going and it's jumpering to all of these buttons.
19
and then button one continues on to input zero.
20
We're just going to concentrate on button one to start with.
21
So we're going to take 24 volt from our plus DC.
22
We're going to go to our green contact on our button one, and then we're going to connect it to input zero.
23
On our buttons here, they all have a green contact and a red contact.
24
Our green contact is going to be a normally open contact, and our red contact is going to be a normally closed contact.
25
And it also says right on the green ones were normally open.
26
NC on the red ones for normally closed.
27
And on our trainer, it does plug into 110.
28
We have 110 here, which powers our PowerFlex drive.
29
It has a 24 volt DC power supply right here.
30
And that 24 volt DC power supply has landed on these sets of terminals.
31
So the left set of four terminal blocks here is our plus 24 volt.
32
And the right set of four terminal blocks is the zero volt or the minus.
33
our green contact, we'll connect it to plus 24 volts.
34
And then we're gonna connect a wire from the bottom of our green contact, and we're gonna connect it to input zero.
35
All right, and a lot of people say, OK, we're done.
36
We're not, because going back to that syncing and sourcing video, remember, we have to have current flow through our PLC input for it to work.
37
So right now we've got to wire from the plus of our power supply up to our switch.
38
Then we go from the other side of our switch.
39
to our PLC input.
40
But what we've left out is this little bit of wire here
41
from the other side of the PLC input back to the minus of our power supply.
42
And this is the most common thing I see people leave out on their circuits.
43
They call me and they're like, "Hey, I've wired all this up, and none of my input lights work." Well, they don't have a complete circuit, 'cause they've left out that minus.
44
And it can be a little bit more confusion, especially in the L18 compact logics, because the common is not with the input.
45
So we have input zero through seven, and eight through 15 here.
46
We don't see that common for that part to go back to the minus of our power supply.
47
And it's over here on the main terminal.
48
It's the FP plus terminal and FP minus terminal.
49
You need to connect the minus of our power supply to the FP minus terminal to complete that circuit.
50
So we're gonna take a wire from the minus of our power supply, and we're gonna connect it to the FP minus terminal.
51
One thing I'd say, especially as you're starting out, is check your wiring often.
52
So hook up a few circuits, check and see if it works, hook up a few more, check and see if it works.
53
Because if you hook up all of this, and let's say you short something out somewhere, it's gonna be a lot more difficult to find the problem.
54
You're going to get frustrated a lot quicker.
55
So let's go and power this up and make sure input zero works.
56
Alright, so we're powered up and we hit button one and sure enough input zero is illuminating.
57
Also if you're using our trainer and the default getting started programs in it, then output zero is also limiting.
58
Don't worry about it right now.
59
We'll talk about it at the end of the video.
60
So our wiring is right, but before we move on, Let's take this FP minus terminal loose, just so you can understand what I was talking about,
61
about the circuit not being complete.
62
So we've taken that wire off.
63
And now I'm going to press button one.
64
and we're not getting input zero.
65
So in this case we have power from the plus of
66
our 24 volt going to the top of our green contact
67
and then out of the bottom of our green contact we're going to input zero
68
but we don't have that last little piece of our circuit.
69
So if you have a similar situation where you're pressing the button
70
and you're sure that the power is wired right to it it's gonna be the issue.
71
So I'm gonna connect the FP minus back before I forget about it.
72
And now we're gonna wire the rest of our buttons.
73
And we're gonna start with the power to our buttons.
74
So we had a power already at button one, and we're gonna jumper that.
75
across the top.
76
So each one will need a wire tying them together.
77
So we'll need a wire from button one to button two, and then button two to button three, then button three to button four,
78
then button four to to switch one
79
and then we already have a power wire coming across so that will give us power
80
on the top of all of our green contacts.
81
Okay, so that takes care of getting power to the top of all of our buttons.
82
Now we're gonna connect a wire from the bottom of each green contact to its corresponding inputs.
83
We've already connected button one to input zero.
84
Now we're going to take button two to input one, button three to input two, button 4 to input 3 and switch 1 to input 4.
85
Now notice those are not perfectly in line 1 :1, 2 :2, 3 :3, so don't get those confused.
86
Okay, looking at our getting started guide, we now have all of our input side wiring done.
87
So you should have wires going on the top of all the green contacts of buttons one through four and switch one.
88
And then you should have a wire going from the bottom of each green contact of button one
89
So you should have five wires connected to the first row of terminal blocks, and we have that field power minus terminal connected.
90
And let's test it out.
91
Button one is going to turn on input zero.
92
And we'd already tested that, but it's good to test it again since we added some more wires.
93
Button two is going to turn on input one.
94
Button 3 is going to turn on input 2.
95
Button 4 is going to turn on input 3.
96
And switch 1 is going to turn on input 4.
97
You'll see a sequence going across here once switch 1 is on.
98
Like I said, just ignore the outputs for now.
99
If yours is not doing that, take the time just to trace out that wiring and figure out what the problem is.
100
Don't move any further.
101
And again, the one that I really think you'll probably forget is this FP minus terminal.
102
And let's just do an exercise to see how we can figure
103
that out because I'll show you how easy it is to think that you have it wired right.
104
So I'm gonna just connect the minus of my voltmeter to one of my minus terminals, which would be typically how I really do troubleshoot.
105
And then I'm going to set my voltmeter to DC volts.
106
See if we can set that in there.
107
Bye.
108
And we're going to take this FP minus terminal off again.
109
Now, when we press our buttons, none of them work.
110
But when we go to test here, we have 24 volt at the top of our contact.
111
We also have 24 volt when we press our contact.
112
And even if we take a wire and we slide it right down beside of that terminal, because it's a little tight to get your voltmeter on,
113
the button and we have 24 volt at our terminal.
114
The issue is I'm taking my voltmeter and testing right here at this minus terminal and I'm testing to here, to here and to here.
115
I'm not actually testing across this PLC input.
116
That's where you really have to check at.
117
So since it's the FP minus terminal, if I remove my voltmeter from the minus,
118
and I connect it over here to the FP minus terminal, can you be my assistant for a second?
119
Can you come over and hold that? on button one.
120
I had to get my better half note, what do you want to be called?
121
Yeah, I'm better.
122
I have to get Amber to come help me out on this, but if I check between FP minus and Bye.
123
And button one I don't get anything, I get like 0 .3 volts.
124
So I don't have power across that PLC input.
125
That is the important part, is making sure that that last little bit of circuit is connected.
126
Thank you, my lovely assistant.
127
If you follow that part of the exercise, then make sure that you put your FP minus back on again, because as we play with these,
128
it's really easy to forget to reconnect something.
129
So let's do one last check.
130
Yeah, button one, button two, button three, button four, switch one.
131
So we're good and we're ready to go to our output.
132
So the outputs are on the right hand side of our diagram.
133
and you're gonna see this common going between all of our lights.
134
And in this case, it's going to the minus DC.
135
So looking at our diagram, that's gonna be this connection on this side.
136
So let's go ahead and do that.
137
So we're gonna get a jumper wire from light one to light two, then from light two to light three, then from light three to light four,
138
and then from light four over here to the minus of our power supply.
139
Now we have a jumper wire from one side of each of our lights, and it's going to the minus of our power supply.
140
Next we're going to connect our wire from output 0 to light 1, output 1 to light 2, output 2 to light 3, and output 3 to light 4.
141
- Okay, so at this point, we have our lights completely wired.
142
And again, just like on our inputs, a lot of people will say, "Okay, I'm done.
143
"Let's test it out." Well, let's test it out, just so we can see what will happen right now.
144
And if we press button one, nothing happens.
145
If we press button 2, nothing happens.
146
Three, nothing happens.
147
Four, nothing happens.
148
Switch one.
149
nothing happens.
150
Yeah, when we look at the back of it, it all looks wired right.
151
If we switch switch one, we do see these lights coming on, but the issue is we haven't completed our circuit.
152
So we started with the minus of our power supply.
153
We went around to one side of our light, and then we went from our light up to our PLC output, but we've missed again, this little often overlooked part,
154
which is the PLC common.
155
Or in the case of the compact logics, it's gonna be the FP plus terminal.
156
And that's right above that FP minus terminal over here on the power strip.
157
So we'll connect a wire from FP plus to the positive of our power supply.
158
And now when we press button one, nothing happens.
159
Bye.
160
Well, it looks like we have a learning opportunity.
161
So let's see where I went wrong.
162
So at this point, In between our FP plus and our FP minus, we should have 24 volt and we do.
163
All right, so when I switch button one, I am seeing the input go on.
164
I'm seeing an output.
165
So let's check across light one.
166
And we have no power.
167
So my guess is there's something wrong with my comments.
168
I'm just going to go from the plus 24 and I'm gonna check this light.
169
Oh, we have 24 volt there.
170
Okay, so if you've been following me exactly how I went in this video, then yours is wrong too.
171
And the issue is I'm looking over this table and I can't really see what I'm doing.
172
And I put all these output wires to the second row, So we need to move them over to this third row,
173
which is output 0 through 7.
174
So we'll just shift these wires over to the third row.
175
There, proof positive I make mistakes.
176
Let's try it again.
177
Now that we have them hooked on the right outputs, we press button one and the green light illuminates.
178
We press button two and the yellow light illuminates.
179
We press button three, the red light illuminates.
180
We press button 4, the blue light illuminates, and we switch switch 1 and it goes through this sequence of lights.
181
And if it does all this, then your trainer is wired right.
182
Now, that is if you bought one of our trainers that comes with the Getting Started program.
183
I'll put the getting started program down in the description.
184
That way you can put it in yours if you didn't buy it from us.
185
Now, if yours doesn't do this, then don't get frustrated.
186
Use it as like, like I just did a learning opportunity to figure out
187
what you did wrong because those are things that you'll run into out in the field.
188
And that's one reason our trainers don't come pre -wired.
189
It's just, yeah, we want you to learn programming, but the bulk of your problems will not be in the PLC.
190
They will actually be in your wiring.
191
So this exercise right here is really good for getting a firm understanding not only on how to wire a PLC, but also how to troubleshoot the wiring.
192
Now make sure you do watch the sinking and sourcing video that I have a link to down in the description.
193
It'll be really important as you move along trying to figure out how to wire a PLC your PLC inputs and outputs.
194
One other thing I just thought of is you may be looking at this and saying, boy, that's really a mess.
195
Well, you can take yours and you could cut yours and make them really neat.
196
Your trainer came with plenty of wire.
197
I don't do it because I may take this trainer apart and put it back together 10 times in a day, depending on what exercises we're doing.
198
I think that about finishes up this video.
199
Please like this video and subscribe because we are putting out a whole series on Studio 5000.
200
In fact, we put out at least one video a week.
201
Put in the comments any questions you have or suggestions for videos.
202
We're always looking for great ideas.
203
Till next time.
204
Hey buddy, how was your day?
205
- What's up?
206
What's going on?
207
Um, no. Nothing like it.
208
Science Fair project.
209
What are you thinking?
210
I really like the idea of seeing if digested waves can produce electricity.
211
Wow.
212
So there you go, we may do a science for a video on.
213
how to take digesting waste and produce electricity.
214
That would be a great idea.
215
All right, we'll brainstorm more on it.
216
Daddy, you want to know something cool?
217
I got an 84 and a test in math!
218
How do you get an 84 in math?
219
The 90 .1 in the gradebook, I got an 84 in the test.
220
That's good!
221
That's bad!
222
That's good.
223
That's bad.
224
C would be bad.
225
A B is good.
226
A 100 is what you should get in math.
227
We get B's in English, not in math.
228
I have a bunch of for A in English.
229
Hey, this is Tim.
230
And this is Amber of TW Controls.
231
We run the Automation Store.
232
Hey, thanks for finding our channel!
233
Here's a playlist with some similar videos.
234
And YouTube thinks you'll like this video.
235
Please like our video and subscribe to our channel.
236
And if our videos have helped you make some money and you're not using our products, please consider supporting us on Patreon.
237
Till next time.
238
See ya!
ऐप डाउनलोड करें
धाराप्रवाह बोलने के लिए ज़रूरी सब कुछ
AI उच्चारण स्कोरहर वाक्य का स्कोर
IPA अभ्यासहर ध्वनि में महारत
शब्दावलीअपना शब्द भंडार बनाएँ
शब्द गेमखेलते हुए सीखें
FOR YOU
अनुशंसित वीडियो
C11
138 वाक्य
Going Online with a PLC, Uploading and Downloading Code!
Daily ConversationWorking Adults
C11
114 वाक्य
BAS Bootcamp: Day 6 Setting up IO Internally
Daily ConversationWorking Adults
C1146 वाक्य
How to Wire an Electrical Outlet 2 Ways (Pigtails vs Daisy Chain) Step-by-Step Guide | Builds by Maz
Daily ConversationWorking Adults
C133 वाक्य
Well Pump Current #electrical #motorcontrol
Daily ConversationWorking Adults
C11
19 वाक्य
Types of Proximity Sensors! #automation #engineering #science #robotics #electronics
Daily ConversationUniversity StudentsWorking Adults
C18
157 वाक्य
How Landing Gear Works | Part 6 : Main Gear Steering
Daily ConversationWorking Adults
C11
53 वाक्य
Construction Site Logistics Map Explained: How Jobsite Layouts Actually Work
Daily ConversationWorking Adults
C11
146 वाक्य
🚫 Java Deadlock Explained: Why Your Code is Stuck 😱 (Beginners Must Watch!)
Daily ConversationUniversity StudentsWorking Adults
C14
85 वाक्य
Transition to and from display: none
Daily ConversationWorking Adults
C1378 वाक्य
How To Wire a House Main Electrical Panel Load Center & Layout Tips Full Step By Step Process 200Amp
Daily ConversationUniversity StudentsWorking Adults
C11
132 वाक्य
Helpdesk to Sysadmin - 3 Things You Must Learn First
Daily ConversationUniversity StudentsWorking Adults
C11
41 वाक्य
Making a 360° Controller Smaller than a Penny!
Daily ConversationUniversity StudentsWorking Adults
इस पाठ के बारे में
इस पाठ में, आप Allen-Bradley CompactLogix PLC के इनपुट और आउटपुट को वायर करने की प्रक्रिया पर ध्यान केंद्रित करेंगे। यह सीखना महत्वपूर्ण है कि कैसे सिंगिंग और सोर्सिंग तकनीकों का उपयोग करके विद्युत सर्किट को सही रूप से कनेक्ट किया जाता है। इस वीडियो से आप समझेंगे कि एक सफल सर्किट के लिए आवश्यक वायरीकरण कैसे किया जाए और आप इसे सही तरीके से कैसे स्थापित कर सकते हैं। यह ज्ञान आपकी अंग्रेजी बोलने और समझने की क्षमताओं को बढ़ाने में भी मदद करेगा, खासकर जब आप शैडोइंग तकनीक का अभ्यास करेंगे।
मुख्य शब्दावली और वाक्यांश
- PLC (प्रोग्रामेबल लॉजिक कंट्रोलर)
- सिंगिंग और सोर्सिंग
- इनपुट और आउटपुट
- DC पावर सप्लाई
- जंपर कनेक्शन
- नॉर्मली ओपन और नॉर्मली क्लोज़ कांटेक्ट
- वायरिंग सर्किट
- पूर्ण सर्किट
अभ्यास टिप्स
इस वीडियो में जो गति और टोन है, उस पर ध्यान केंद्रित करना महत्वपूर्ण है ताकि आप सही तरीके से अभ्यास कर सकें। अंग्रेजी शैडोइंग विधि का उपयोग करते हुए, आप वीडियो को ध्यान से सुनें और उसके साथ-साथ बोलने का प्रयास करें। अपने उच्चारण और स्पीड पर ध्यान दें। आप shadowing site पर कई संसाधन पा सकते हैं जो आपको अपनी उच्चारण क्षमता में सुधार करने में मदद कर सकते हैं। जब आप वीडियो के साथ शैडो स्पीच करते हैं, तो यह सुनिश्चित करें कि आप हर वाक्य और उसकी संरचना को समझने की कोशिश करें। इससे आपका आत्म-विश्वास बढ़ेगा और आप अपनी अंग्रेजी बोलने की क्षमताओं को प्रभावी ढंग से सुधार सकते हैं।
इस वीडियो का व्याकरण
वक्ता जिन संरचनाओं का सबसे अधिक प्रयोग करता है, वीडियो के असली शब्दों के साथ:
| संरचना | वीडियो में |
|---|---|
| Present perfect have/has + past participle — बीता हुआ काम जिसका असर अभी भी है | has landed · we've left · I've wired |
| Passive voice be + past participle — ज़ोर इस पर कि क्या होता है, न कि कौन करता है | be wired · is wired · be called |
शैडोइंग तकनीक क्या है?
शैडोइंग (Shadowing) एक विज्ञान-समर्थित भाषा सीखने की तकनीक है जो मूल रूप से पेशेवर दुभाषिया प्रशिक्षण के लिए विकसित की गई थी। विधि सरल लेकिन शक्तिशाली है: आप मूल अंग्रेज़ी ऑडियो सुनते हैं और तुरंत इसे ज़ोर से दोहराते हैं — जैसे वक्ता की छाया 1-2 सेकंड की देरी से। शोध से पता चलता है कि यह उच्चारण सटीकता, स्वर, लय, जुड़ी हुई ध्वनियाँ, सुनने की समझ और बोलने की प्रवाहशीलता में काफ़ी सुधार करता है।