शैडोइंग अभ्यास: EDFR GWO BTT Training Center - Nicolas Riou Wind - YouTube के साथ अंग्रेजी बोलना सीखें

Welcome to the Nicola Rio Technical Training Center

⏸ रुका हुआ

गति:

106 वाक्य

यदि वाक्य बहुत छोटे या लंबे हों, तो समायोजित करने के लिए Edit पर क्लिक करें।

Welcome to the Nicola Rio Technical Training Center

and I will show you today how we installed the equipment

and give you an introduction about every equipment that we have here.

For the mechanical part, we have a full torqueing equipment inside here so we can

torque with the hydraulic tool and the electrical tool so the high-torquing

equipment are here and we have also an installation to stretch a bolt

so it's a low pressure

but it's still working like same than we are inside a

wind turbine we have a full pump high torque pump here plus a half nt3 pump socket that we can

that we can simulate a torqueing session here.

For the mechanical also we have another small bench here

so we can use a standard torque wrench

and show to the student difference when we torque a boat between the lubricate boat

and non lubricate boat and we can use digital galliper

and measuring tool to make the difference between the stretch on the boat on the electrical side

so for the mechanical it's what we have here on the bench

but we still have a four-yard drive

and we have three pitch system pitch drive including the motor

and the gearbox

and we also can do here a test torque test with the bolt the mounting bolt of the gearbox

itself plus the electric motor to the gearbox

so we have a lot of things here to play with

for the mechanical part for the electrical part now we have a full sanbyon electrical cabinet exactly the same cabinet

that we have inside the sanbyon winter bean

so there's no difference we installed all electrical cabinet and everything starts here with the converter.

Converter, all of the cabinet are supplied with a 600 volt AC 3-phase.

We have a 60 amps capacity to supply all of the auxiliary systems,

including the pitch system.

So we start here with the 1S1 cabinet.

This is the main connection cabinet where the grid is connected and the stator of the generator.

We have here the 1S2 cabinet where we have the auxiliary equipment and the auxiliary supply for the winter beam.

One S3, one S4 and one S5 cabinets.

So this cabinets are the real converter.

There's an IGBT filtering cabinet plus the main converter controller is there, the CSC4.

After that we have the base box.

This is where the communication to the wind farm is located.

The switches are here, the fiber optic switch.

Plus they have also a back-mounted slave module inside this cabinet.

The top box,

this is the brain of the wind turbine is where the

backman computer backman tlc is located with the distribution of the 575

or 600 volt in our case to supply all of the electric motor the fan generator fan gearbox fan motor

the motor etc

so our cabling everything is original from the winter me we didn't change nothing we use exactly the same cabling

that they have inside of intervie we just adapted everything to make sure

that it fits in our location that we have here.

For the electric part, we also have all sensors that they have inside the NASO,

inside the real NASO.

So we have here a full set of PT100,

PT1000 proximity switch, and we have the 4 to 20 milliamp simulator.

So this represents the pressure gearbox oil transmitter.

So instead of having the real transmitter,

we installed a simulator here to simulate the

1420 milliamps and they are very good to show them how the process control signals are working.

We have also a selector switch here to simulate the pressure switch,

how the pressure switch are working with the logic that they have linked together inside the SCADA,

inside the backmount computer.

The thoraconic anemometer, it gives the wind speed and the wind vein direction.

We have a cup anemometer on the top of the top box,

plus an analog wind vein tube.

The sleep ring here, this is exactly the same model that we have inside the wind turbine.

So the signal came from the top box,

passed across the sleep ring and goes to the cable harness.

This is exactly the same cable harness that they have on the machine.

And it's going on the other side to supply the pitch

system with the 400 volt AC main supply plus communication and the control signal.

Hydraulic stations, this is another module that we can fully cover on the BTT.

So we have here the original,

the same hydraulic unit that they have installed inside the S&V wind turbine.

And we have one Yaga dipper and one Rotter dipper.

So the Yaga dipper, it's just one instead of having between 8 to 12 dipper inside the S&V machine,

depending on the type.

But it's fully functional, so it's exactly the same pressure, the same signal.

And we have here the Rotter hub dipper.

So the rotor half gallipper,

we have kind of big plate of steel here to simulate the real disc brake

that we have inside the machine and everything is fully functional.

For the electrical part, we also have here a small simulator and this simulator they have contactor,

two relays, pilot light plus here we have a small remote to control the pilot light

and to control the equipment on this small board.

We can teach the parallel series logic with the

board light that we have here

and we can teach also the relationship between the AC

and DC we have a power supply everything is supplied with 120 volt AC connected to a GFCI service circuit

so everything is safe everything is touch safe

so it's a very very useful to teach what's the difference between the relay and contactor,

or they are the same in the same times, they are so different.

So this is a very nice small bench to work with.

On the other side we have here the complete pitch system.

So on the table we have the,

yeah this is a SSD pitch system,

we have the access cabinet on the top where are located the DC trans

and all of the contactor and the equipment to drive the pitch motor

and on the floor here there is the battery cabinet.

Battery cabinets are fully loaded of batteries it's exactly the same than the winter bean is working the same.

Central cabinet here we have the we call it the LBV

cabinet this is this is where the pitch controller is located

and this is the brain of the pitch system we have all three pitch motor pitch drive

and we have the pinion down here inside the inside this

100

small cabinet here it's protected with plexiglass for safety we have the secondary encoder

101

and color eb limit switch and again all wiring

102

that i use here is exactly the same wiring

103

that we have inside the machine

104

so everything is fully functional here for the for the water hub everything is working so i think the tour is complete.

105

I hope that you like our setup that we have here

106

and we have we have place for training for you guys so just let me know

TRENDING

शैडोइंग तकनीक क्या है?

शैडोइंग (Shadowing) एक विज्ञान-समर्थित भाषा सीखने की तकनीक है जो मूल रूप से पेशेवर दुभाषिया प्रशिक्षण के लिए विकसित की गई थी। विधि सरल लेकिन शक्तिशाली है: आप मूल अंग्रेज़ी ऑडियो सुनते हैं और तुरंत इसे ज़ोर से दोहराते हैं — जैसे वक्ता की छाया 1-2 सेकंड की देरी से। शोध से पता चलता है कि यह उच्चारण सटीकता, स्वर, लय, जुड़ी हुई ध्वनियाँ, सुनने की समझ और बोलने की प्रवाहशीलता में काफ़ी सुधार करता है।

☕ हमें एक कॉफी पिलाएं

आपके समर्थन के कारण ShadowingEnglish 100% मुफ्त है। सर्वर और AI की लागत अधिक है — आपकी कॉफी हमें आगे बढ़ने में मदद करती है! 🙏

PayPal के माध्यम से दान करें

ShadowingEnglish.com – अंग्रेज़ी शैडोइंग अभ्यास

शैडोइंग अभ्यास: EDFR GWO BTT Training Center - Nicolas Riou Wind - YouTube के साथ अंग्रेजी बोलना सीखें

लोकप्रिय

इस पाठ के बारे में

प्रमुख शब्दावली एवं वाक्यांश

प्रैक्टिस टिप्स

शैडोइंग तकनीक क्या है?

शैडोइंग अभ्यास: EDFR GWO BTT Training Center - Nicolas Riou Wind - YouTube के साथ अंग्रेजी बोलना सीखें

ऐप डाउनलोड करें

इस पाठ के बारे में

प्रमुख शब्दावली एवं वाक्यांश

प्रैक्टिस टिप्स

शैडोइंग तकनीक क्या है?