Pratica di Shadowing: Single Phase Electricity Explained - wiring diagram energy meter - Impara a parlare inglese con i video
Scegli una modalità di pratica
Ogni modalità apre una sala di pratica a schermo intero.
129 frasi
Se le frasi sono troppo corte o troppo lunghe, clicca su Edit per modificarle.
1
Hey there guys, Paul here from TheEngineeringMindset .com.
2
In this video, we're going to be looking at a typical single -phase electricity supplier into a domestic property.
3
We're going to look at the distribution cables and transformer, the phase neutral on earth, the main fuse, the electricity meter,
4
the isolation switch, the consumer unit as well as the RCDs and MCBs.
5
Now, this is a common design used across the UK, Europe, India, Australia, New Zealand, etc. There are some slight variations,
6
and these components may look a little different between the countries, but essentially it's very similar.
7
However, North America is a little different because they use two voltages in the homes,
8
so we're going to look at that in detail in a separate video.
9
You can still follow along in this video to understand the basics, though.
10
I'm going to be using the European color codes for this video that may be different from your local regulations.
11
Remember, electricity is dangerous and can be fatal.
12
You should be qualified and competent to carry out any electrical work.
13
So the electricity is generated far away at the power station.
14
The electricity leaves the power station
15
and the voltage is increased in a step -up transformer where it will then be distributed over long distance transmission lines.
16
We generate and distribute AC alternating current because it is more efficient and convenient than DC direct current.
17
Once it reaches the town, the voltage will be reduced in a substation step -down transformer.
18
If you want to learn how transformers work, we've covered this in a previous video, do check that out, links in the video description below.
19
From the substation, the electricity will either be distributed locally through overhead or underground cables.
20
Depending on the local design and the voltages being used, a home might be connected directly to a small transformer located close to the property
21
or alternatively a group of houses will share a larger transformer.
22
The electricity is distributed in three phases
23
but in this case we're looking at a single phase installation
24
which means the property is connected to just one of these three phases as well as the neutral.
25
We've also covered how three -phase electricity works in a previous video do check that out links in the video description below.
26
Now, each house in a street might be alternately connected to a different phase
27
or different streets might be connected to different phases.
28
This is just to try and balance the demand on the transformer.
29
A smaller service cable comes off the distribution cable and will feed the property.
30
This service cable will again be overhead or underground depending on the local installation.
31
The service cable contains the phase and neutral wires.
32
There's also a metal protective sheath around the cable in most cases especially
33
if it's buried underground the service cable comes in the electricity
34
is going to flow through the phase pass through the main fuse then through the electricity meter
35
and then into the consumer unit the service head
36
or cutout holds the main fuse
37
or service fuse this fuse provides protection to the property
38
and ensures only a set amount of current can flow into the property for example in the uk
39
it's typical to have a fuse rated between 60
40
and 100 amps the electricity distribution company may also remove this fuse to isolate the property.
41
They may do this for example to replace the electricity meter.
42
The phase and the neutral then enter the electricity meter which quantifies how much energy is being consumed.
43
You may find that this meter is mechanical or electrical or even a digital smart meter.
44
There are a lot of variations of design for these.
45
The phase and the neutral will then leave the electricity meter and enter the consumer unit or fuse board.
46
The The consumer unit or fuse board varies in size depending on the size of the property
47
and how many circuits there are being controlled.
48
Inside the consumer unit we first have the main switch or main double pole isolation switch.
49
This controls the supply of electricity to the rest of the consumer unit and therefore all the circuits feeding the property.
50
This switch is not automatic and must be manually flipped to cut the power.
51
This switch will disconnect both the phase and the neutral line together.
52
The cables typically enter the main switch via the top terminals.
53
At the bottom we find the neutral wire which will connect to the neutral block connection.
54
We might find one or more phase wires coming out of the bottom of the main switch to feed the RCDs.
55
If there aren't RCDs being used, then a bus bar will feed the circuit breakers but we'll look at that again shortly.
56
The phase line enters the RCD or residual current device, again usually entering via the top.
57
This RCD switch is constantly monitoring the electrical current.
58
It's checking if the current in the phase line is equal to the current in the neutral line.
59
If these two currents are not equal,
60
then there is an electrical fault and the device will quickly and automatically cut the power to everything past the switch.
61
Typically, an RCD will break the circuit
62
if it measures a difference of 30 milliamps as anything above this is dangerous for humans.
63
If you touch a live wire and electricity flows through you to the ground,
64
then the current is bypassing the neutral wire so the phase and the neutral currents will not be equal.
65
The RCD will notice this and then cut the circuit to reduce the risk of electric shock or death.
66
It's now increasingly common to have two or more RCDs in a consumer unit.
67
In such case, the RCD will only cut the power to the circuits connected directly after it.
68
So the other RCD will still be powered and only some parts of the property will lose power.
69
The RCD will trip when it believes the current is unsafe even for a fraction of a second.
70
It does need to be manually reset to restore the power,
71
but this does not solve the problem and you should locate and remove any faulty appliance or fixture.
72
From the bottom of the RCD, we have a buzz bar.
73
This is just some conductive metal which the electricity flows along and connects into each of the MCBs,
74
which just makes the installation easier rather than having a lot of cables.
75
The MCB or miniature circuit breaker controls individual smaller circuits.
76
For example, connected to one RCD, maybe we'll have one MCB for the downstairs lighting, one for the upstairs lighting,
77
and one for the kitchen plug sockets.
78
On the other RCD, maybe we have one for the stairwell lighting, one for the upstairs lighting, and one for the downstairs plug sockets.
79
These switches will quickly and automatically trip to cut the power, but they also need to be manually set to restore the power.
80
The MCB protects the circuit in two ways, overload and short circuit.
81
The MCB is rated to handle a certain amount of current passing through it.
82
For example, 32 amps for the plug sockets.
83
If this value is exceeded on that circuit, for example, by gradually plugging in too many things,
84
then the MCB will trip and cut the power to protect itself.
85
The other protection it offers is short circuit protection.
86
In the event of a short circuit, for example, the live touches the neutral,
87
then the circuit is bypassed and there may be a large and instantaneous increase in current.
88
This will create a magnetic field inside the MCB which will cut the power to protect itself.
89
The phase then leaves via the top of the MCB and will flow through the circuit, for example through some lamps.
90
It then returns via the neutral cable and into the neutral block.
91
All the circuits do this with the phase coming out of the circuit breaker
92
and heading off around the property and the neutral lines coming back and meeting at the neutral block.
93
The neutral block is then connected to the RCD which checks
94
if the current flowing in is equal to the current flowing out.
95
The neutral then flows from the RCD to the main neutral block
96
and from there back to the main switch which is connected to the electricity meter and the service head.
97
So electricity can then flow from the main distribution phase line up through the service head and the main fuse.
98
It then flows through the electricity meter and into the consumer unit main switch.
99
From the main switch it flows through the the RCD, along the buzz bar and into the MCB.
100
It then flows up around the MCB separated circuits.
101
The electricity can then come back via the neutral lines and into the neutral blocks.
102
It then flows through the RCD and back into the main block.
103
From there, back into the main switch and then the electricity meter.
104
It will then pass through the service head and the fuse and back into the neutral line of the main distribution cables.
105
Now you may have noticed that there's some other cables with green and yellow stripes.
106
These are called the IRF cables.
107
This IRF cable usually runs along with the phaser neutral wires into the fixtures such as light switches and plug sockets.
108
Some appliances will also use an IRF wire for added protection, typically if the device uses a metal casing.
109
The IRF wires will connect from these fixtures into the neutral block with the consumer unit.
110
All the IRF cables for each circuit then connect into the IRFing block in the unit.
111
Another IRF cable will then connect from this IRFing block in the consumer unit over to the main protective earthing terminal,
112
which is typically located somewhere near the electricity meter.
113
Other earthing wires will connect from this main earthing terminal over
114
and onto metal pipes such as the plumbing and the gas pipework.
115
That way, if a person touches a live wire in a metal pipe in the property,
116
the electricity will flow through the earth wire and should be detected by the RCD, which will cut the power.
117
There are a few ways the main protective earthing terminal is connected to ground.
118
The first option is shown here, with the main earth terminal being connected to the neutral wire of the service cable within the service head.
119
This means that the phase to earth fault is effectively now a phase to neutral fault instead.
120
Another option is to use the metal protection sheath around the service cable as the earth conductor.
121
So the main earth terminal is connected to the metal sheath
122
and this carries the phase to earth fault back to the transformer.
123
The other option, which is when the electricity supplied doesn't provide an earth path
124
so instead the main earth terminal is connected to an electrode rod
125
which is installed into the ground and provides a direct earth path.
126
Okay that's it for this video but
127
if you want to continue your learning then check out one of the videos on screen now
128
and I'll catch you there for the next lesson.
129
Don't forget to follow us on Facebook, Twitter, Instagram and of course theengineeringmindset .com.
Scarica l'app
Tutto ciò che serve per parlare fluentemente
Pronuncia con IAVoto per ogni frase
Pratica IPAPadroneggia ogni suono
VocabolarioCostruisci il tuo lessico
Gioco di vocabolarioImpara giocando
Stesso Canale
B21
Ohms Law Explained - The basics circuit theory
Daily ConversationUniversity Students
B21
Air Conditioning System Basics hvacr how does it work
Daily ConversationWorking Adults
C1120V 240V Electricity explained - Split phase 3 wire electrician
Daily ConversationUniversity Students
B22
How ELECTRICITY works - working principle
Daily ConversationUniversity StudentsWorking Adults
C11
Diodes Explained - The basics how diodes work working principle pn junction
Daily ConversationUniversity StudentsWorking Adults
C1How Electric Motors Work - 3 phase AC induction motors ac motor
Daily ConversationUniversity Students
C1Centrifugal Pump Basics - How centrifugal pumps work working principle hvacr
Daily ConversationWorking Adults
FOR YOU
Video consigliato
C11
118 frasi
Current | Introduction to electrical engineering | Electrical engineering | Khan Academy
Daily ConversationUniversity Students
C1378 frasi
How To Wire a House Main Electrical Panel Load Center & Layout Tips Full Step By Step Process 200Amp
Daily ConversationUniversity StudentsWorking Adults
C1155 frasi
Every Hardware Protocol Explained Simply in 10 Minutes!
Daily ConversationUniversity StudentsWorking Adults
C11
507 frasi
Steam Turbine Construction Operating Fundamentals
Daily ConversationUniversity Students
C150 frasi
GCSE Physics - Energy Stores, Transferring Energy & Work Done
Daily ConversationUniversity Students
C13
279 frasi
LET THERE BE... Voltage? | Maxwell's Equation #2 Explained for Beginners
Daily ConversationUniversity Students
C11
95 frasi
26 - How does harmonic phase shifting work including a detailed mathematical explanation to reduce s
Daily ConversationUniversity Students
C11
19 frasi
I Made an EMP Device... It Actually Works
Daily ConversationUniversity StudentsWorking Adults
C11
51 frasi
What's Under Your Feet in New York City?
Daily ConversationUniversity StudentsWorking Adults
C11
64 frasi
What is SCADA?
Daily ConversationUniversity StudentsWorking Adults
C11
60 frasi
Faces of Chemistry: Organic solar cells (BASF) - Video 2 (14+)
Daily ConversationUniversity Students
Vocabolario e note di pronuncia per questa lezione
Questa lezione di conversazione si basa sul video “Single Phase Electricity Explained - wiring diagram energy meter”. Le parole che ritornano più spesso: neutral, electricity, phase, main, Rcd. Questo video contiene 129 frasi e 1885 parole da ripetere con lo shadowing. Il parlato dura 9:58. Chi parla va veloce, circa 189 parole al minuto: aspettati suoni legati e ridotti. Solo il 79% delle parole rientra nelle 3.000 più comuni dell’inglese, quindi il lessico è impegnativo.
Vocaboli chiave di questo video
15 parole del video che vale la pena imparare, con pronuncia e significato:
| Parola | Pronuncia | Significato |
|---|---|---|
| neutral aggettivo | /ˈnuː.tɹəl/ | neutrale |
| connect verbo | /kəˈnɛkt/ | connettere, connettersi |
| wire sostantivo | /ˈwaɪɚ/ | filo, filo metallico |
| metre sostantivo | /ˈmiːtəɹ/ | metro |
| fuse sostantivo | /fjuːz/ | miccia |
| terminal sostantivo | /ˈtɚmɪnəl/ | terminal, terminale |
| plug sostantivo | /plʌɡ/ | spina |
| voltage sostantivo | /ˈvəʊltɪd͡ʒ/ | voltaggio, tensione |
| distribute verbo | /dɪˈstɹɪbjuːt/ | distribuire |
| socket sostantivo | /ˈsɑkɪt/ | presa, zoccolo |
| underground aggettivo | /ˌʌn.dəɹˈɡɹaʊnd/ | sotterraneo |
| depend verbo | /dɪˈpɛnd/ | dipendere |
| installation sostantivo | /ˌɪn.stəˈleɪ.ʃən/ | installazione, insediamento |
| protective aggettivo | /pɹəˈtɛk.tɪv/ | protettivo |
| locate verbo | /ˈloʊˌkeɪt/ | localizzare |
I phrasal verb che sentirai
| Parola | Pronuncia | Significato |
|---|---|---|
| pass through verbo | trapassare | |
| come back verbo | tornare | |
| carry out verbo | /ˈkæ.ɹi aʊt/ | compiere, realizzare |
| check out verbo | investigare | |
| line up verbo | /laɪnˈʌp/ | allineare |
| step down verbo | ritirarsi, dimettersi |
La grammatica di questo video
Le strutture che chi parla usa di più, con le parole esatte del video:
| Struttura | Nel video |
|---|---|
| Forma passiva be + participio passato — conta ciò che accade, non chi lo fa | is generated · is increased · will be reduced |
| Frasi relative who / which + frase — un’informazione in più su una persona o una cosa | wire which will · MCB which will · switch which is |
| Present perfect have/has + participio passato — un’azione passata che conta ancora adesso | we've covered · We've also covered |
Pronuncia a cui fare attenzione
Chi parla usa 13 contrazioni e forme ridotte, come we're, we'll, we've. Pronunciale nella forma breve, così come le senti.
- I suoni “sh” e “zh”: installation /ˌɪn.stəˈleɪ.ʃən/, variation /ˌvɛəɹiˈeɪʃn̩/, isolation /ˌaɪsəˈleɪʃən/, shortly /ˈʃɔɹtli/, shock /ʃɔk/
- Parole lunghe — attenzione all’accento: electricity /ɪˌlɛkˈtɹɪsɪti/, electrical /ɪˈlɛktɹɪkəl/, installation /ˌɪn.stəˈleɪ.ʃən/, manually /ˈmænj(u)əliː/, isolation /ˌaɪsəˈleɪʃən/
I suoni difficili per chi parla italiano:
- Consonante finale — senza aggiungere una vocale dopo: circuit /ˈsɝ.kɪt/, connect /kəˈnɛkt/, fuse /fjuːz/, plug /plʌɡ/, voltage /ˈvəʊltɪd͡ʒ/
- /æ/ — più aperta della “e”: manually /ˈmænj(u)əliː/, rat /ɹæt/, amp /ˈæmp/, bypass /ˈbaɪpæs/, automatic /ˌɔː.təˈmæt.ɪk/
Come esercitarsi con questo video
- Ascolta tutto il video una volta senza parlare e annota le parole che non conosci.
- Inizia a velocità 0,75×, fai shadowing frase per frase e torna alla velocità normale quando diventa facile.
- Registrati e confronta con l’originale, facendo attenzione a parole come neutral, connect, wire.
Cos'è la tecnica dello Shadowing?
Shadowing è una tecnica di apprendimento delle lingue supportata da studi scientifici, originariamente sviluppata per la formazione dei traduttori professionisti e resa popolare dal poliglotta Dr. Alexander Arguelles. Il metodo è semplice ma potente: ascolti un audio in inglese di madrelingua e lo ripeti immediatamente ad alta voce — come un'ombra che segue il parlante con un ritardo di solo 1–2 secondi. A differenza dell'ascolto passivo o degli esercizi di grammatica, lo shadowing costringe il tuo cervello e i muscoli della bocca a elaborare e riprodurre simultaneamente i modelli di discorso reale. La ricerca dimostra che migliora significativamente la precisione della pronuncia, l'intonazione, il ritmo, il discorso connesso, la comprensione dell'ascolto e la fluidità del parlato — rendendolo uno dei metodi più efficaci per la preparazione alla prova di speaking dell'IELTS e per la comunicazione reale in inglese.