Shadowing Practice: Construction Safety Training Video // Over 40 Topics - Learn English Speaking with Video

Music

Being safe on the work side is all about thinking and paying attention to what you're doing.

Looking out for others is how we can all get home in one piece at the end of the day.

And no matter who you work for, we all need to be following the same safety rules.

And that's what we're going to be talking about in the next few minutes.

So let's start with what you'll be wearing.

You've got to be properly dressed at the work site.

At a minimum, that means hard hat, long pants, heavy-duty work boots with a non-skid sole, a shirt with sleeves, a safety vest or bright-colored shirt, and eye protection.

Check your hard hat to make sure that it's in good condition.

If there's tears in the suspension or holes in it, you'll need a new one.

During the course of a normal workday, you may be exposed to different types of eye hazards, including flying particles, sparks, or chemical splashes.

You need to be wearing eye protection at all times.

That means safety glasses, goggles, a full face shield, or a combination of the three.

There are lots of jobs that require you to be wearing a full face shield over your safety glasses or goggles.

And if you're cutting or welding, you'll need to have special eye protection.

Hearing protection is essential to protect you from noise.

If it's hard to hear a person three feet away without them yelling, you need hearing protection.

There are two types of hearing protections available, earplugs and earmuffs.

In some cases, you may need to wear both.

You never get used to the loud noise.

If you continue to be exposed to it, it can cause permanent damage to your hearing.

You also need the right kind of work gloves.

Heavy-duty gloves will protect against rough or sharp edges, abrasive surfaces, and splinters.

A lot of people don't realize that wet concrete can hurt your skin.

It can cause serious burns and skin irritations, so you need to wear rubber gloves when working with concrete.

And also be sure that you've got rubber boots on.

If your hands or any part of your skin comes into contact with wet concrete, you need to wash the area immediately.

And if you're doing anything with acids, corrosives, or solvents, you really need to be wearing the right kind of gloves gloves.

It's a good idea to remove rings or other kind of jewelry that can catch on a corner and cause an injury.

And if you're wearing a chain around your neck, it needs to be under your shirt.

And if you've got long hair, it needs to be up under your art hat.

Both these things so you don't get caught in any revolving equipment.

There's a lot of heavy equipment in use on our projects, all with different hazards.

Your safety vest or shirt helps make you visible to equipment operators.

And no matter where you are, pay attention to your surroundings.

Getting hit by a piece of equipment or a crane load is one of the leading causes of construction site fatalities.

You're required to attend weekly toolbox talks to discuss safety on the job.

This toolbox talk is for you.

If you have a question or a comment about safety, the toolbox talk is a great time to bring it up.

One other thing you need to be aware of is our drug and alcohol policy.

It's pretty simple.

We don't want you working while you're under the influence of drugs and alcohol.

It's dangerous for you and it's dangerous for everybody around you.

There are times when a company might require you to take a drug or alcohol test.

If you're injured or involved in some kind of accident, you will be required to take a test.

It's not optional.

It's on company time and it's required.

If you test positive or refuse to take a test, you will be subject to disciplinary action up to and including discharge.

Just so we're clear, there's no weapons of any kind permitted on the job site.

The Project Crisis and Emergency Response Plan tells you what to do if there's an emergency, such as a natural disaster, a fire, a hazardous material spell, or some other kind of incident.

The people who have incident commander or emergency coordinator vests are not only there to assist in the event of a crisis,

but also to help answer questions or report potential hazards, quality issues, or near misses.

Other than police or other emergency personnel, they are the only people who should be giving you directions during an emergency.

Don't start doing things unless you're told by a person with one of those vests on.

All injuries need to be reported.

That way we can make sure and get you all the help that you need.

Likewise, if you have a near miss, that needs to be reported so we can learn from it and keep it from happening again.

There's a lot of tasks that require you to be wearing a respirator.

You've got to know the materials you're working with and make sure you have the right respirator for the job.

Respirators will protect you from overexposure to dust, mist, and fumes and must be matched for the exposure.

If you're not sure what type of respirator is needed for the task, have your foreman contact the safety department for assistance.

The most common respirator you will use is a dust mask.

Regardless of the type of respirator you use, the mask has to have a good seal around the face.

This is accomplished by being clean-shaven, using both head straps and adjusting the nose piece to fit your nose.

And if you're near an operation where workers are wearing respirators, you may also need to be protected.

Nearly 1,000 construction workers are killed each year on the job.

That's more than three workers every day, and about a third of those are because of falls.

All of those can and should be prevented.

Any place that there's a potential fall of more than six feet, you need to be protected.

It doesn't matter if it's an opening in the floor or around the outside of a building.

The most common type of fall protection is a guardrail.

Guardrails need to be constructed of either wood or wire rope, and have a top rail that's 42 inches off the ground, a mid rail, and a tow board.

If you remove a guardrail, alternate fall protection must be used, and never leave an area unprotected for any period of time.

You must reinstall the guardrail before you leave the area.

If you're working at an elevation where guardrails don't provide enough protection, such as off a ladder near an open-sided floor, you also need to wear fall protection gear.

Another common form of fall protection is a personal fall arrest system.

This includes a harness, a lanyard or retractable lifeline, and an attachment point.

You've got to inspect your harness daily for cuts, tears, and frayed straps.

Buckles, snap hooks, and safety latches all need to be looked at at any time you put on a harness.

If anything is broken or damaged, don't use it.

Give it to your foreman so that nobody else uses it either.

To put on a fall protection harness, start by securing your waist buckle.

Then the chest buckle.

Next, the two leg buckles.

And finally, recheck everything to make sure that they're tight.

The most important part of a fall arrest system is the attachment point.

A general rule of thumb is that the anchorage point must be capable of supporting twice the maximum load.

Most fall protection manufacturers say that means at least 3600 pounds.

If you're not sure if the anchorage point can hold that much, ask your foreman.

Always try to tie off above your head and make sure you limit your fall to no more than six feet.

When you're climbing a wall or column, you either need to use a retractable lifeline or utilize a double tie-off.

The retractable lifeline, some people call it a yo-yo, will generally be attached to the upper part of the wall or scaffold.

So all you have to do is attach it to your harness and start climbing.

And when you're done, remember to attach the lifeline to the base of the column

so it will be there for the next person to use.

If you don't have a retractable lifeline, then you need to use the double tie-off method.

To do that, you need two lanyards.

If you're climbing a form using two lanyards, you start by tying off as high as possible with the first one.

Climb until that tie-off point is waist high, then take the second lanyard and tie off again as high as you can before unhooking the one at your waist.

100

Climb again until the tie-off point is waist high, and continue the process until you reach your work area, and then reverse the process to come back down.

101

And finally, controlled access zones or warning lines and barricades are used to prevent people from coming near a fall hazard.

102

You need to be using fall protection when you're inside the unprotected area.

103

Before you use a ladder, inspect it to make sure it doesn't have any broken rungs or cracked or split side pieces.

104

If it does, don't use it.

105

Take it out of service.

106

Before you start climbing, check to make sure

107

that the ladder is set on a sound base and the side braces or locks.

108

And don't ever use the top two steps to stand on.

109

If you're on an extension ladder, then the ladder hooks need to be properly set and the ladder has to be tied off.

110

When you're climbing, always use both hands.

111

Tools or materials need to be pulled up in a bucket or by a rope.

112

It's the safest way to go up and down a ladder, and you'll always have at least one hand on the ladder.

113

And be sure to face the rungs or steps when you're working off or climbing up or down a ladder.

114

There are lots of holes on a job site.

115

They may be a few inches in diameter to several feet across.

116

You've got to make sure they're marked and covered properly, otherwise it's a serious safety hazard.

117

Building a proper hole cover is only half the job.

118

You've got to make sure it's secure, that it won't move, and that it's marked clearly.

119

A lot of jobs will require you to work on a scaffold.

120

You need to inspect it yourself.

121

Make sure that it's on a solid footing and that it's level.

122

And if it's more than two sections high, it needs to be tied off.

123

And then the other thing

124

that you really want to be sure of is whether the planking

125

and supports are in good condition and the boards are secure.

126

And make sure guardrails are in place on any open sides and that there are cross braces.

127

Delivering a quality project really takes a team effort.

128

Every single part of the building is important.

129

The quality of the concrete pour that you may be working on today impacts the quality that occurs later on, such as flooring, millwork, and equipment installation.

130

Just about every project that you work on is going to have a series of mock-ups constructed.

131

There may be a 3D computer model that we'll use in our pre-installation meetings, but there will also be full-size mock-ups like this one.

132

A wall mock-up lets us practice what we're going to build

133

and make sure that we have all the details completely worked out.

134

If there's a mock-up for your part of the work, you need to review it with your supervisor to make sure you understand exactly how things are put together.

135

Otherwise, you may end up having to tear it out and do it again.

136

Make sure you review the drawings and manufacturer's installation guidelines with your supervisor before starting your work.

137

The number one problem we typically find during quality inspections is someone did not follow the manufacturer's instructions.

138

Every product is different, and manufacturers change their installation procedures a lot.

139

Always have a copy of their instructions available to keep you straight.

140

We try to cover most of this during the pre-installation meetings,

141

meetings, and sometimes we'll even have computer-generated sequence details to show you layer by layer how things go together.

142

Don't be shy about asking questions.

143

We'd rather solve issues early than find a problem later.

144

Quality inspections are part of our normal routine.

145

The people reviewing your work are not out to get you, they're just part of the team that's trying to prevent problems and make sure we're delivering quality construction.

146

If you see something that doesn't appear right, Tell your supervisor and let's make it right.

147

If you've got questions about how to do something, ask the quality assurance manager assigned to the project.

148

Any time that ductwork is stored on site, it needs to be kept off the floor and the ends need to be covered over.

149

It's important that the ends are sealed, both before they're installed and then after they're in place.

150

If we don't do that, then dirt and dust can get inside them and spread all over the building.

151

We always wipe down the inside of ducts before they're put in place so that they are really clean.

152

When we finish work in an area, we want to protect it.

153

If you are in an area where you see work that has been covered to protect it, be extra careful.

154

And if you see something that has gotten damaged, report it to your foreman.

155

Most job sites will also have a lot of trenches that we need for underground utilities or foundation.

156

Any time that you are working in a trench or confined excavation that's more than 5 feet deep, it has to be braced, shored, or sloped back.

157

This includes the area between the foundation wall and earth bank.

158

Even a large foundation excavation can become a trench once we start putting in formwork or walls.

159

Any excavation must be inspected every day before anyone goes into it.

160

Do not enter a trench until a competent person has done the inspection.

161

Most often this will be the foreman of the team that dug the trench.

162

Never go down into an open trench unless the excavation is properly shored, not even for a minute.

163

Otherwise, there's the chance that if the soil gives way, you'll be buried and either be crushed or suffocate before we can dig you out.

164

And there should always be a ladder or a ramp within 25 feet of where you're working.

165

It is important that you understand how to lift properly so you don't hurt your back.

166

When you lift something, keep the load as close to your body as possible.

167

Keep your back straight and lift with your legs.

168

When you're carrying something heavy, don't make sudden or rapid movements and watch out for anything that might make you suddenly have to stop or change directions.

169

And remember to be careful when you put something down.

170

Use your legs to lower it, not your back.

171

Just about everybody will use small hand tools sometime during their shift.

172

If you're not familiar with a tool that you need to use, don't use it until you're properly trained.

173

The first thing to do is to really inspect the tool.

174

Check all guards to make sure that they operate freely and don't hang up or stick.

175

And if there's cuts, nicks, or damage to power cords, or if the grounding pin is missing on the plug, the tool needs to be taken out of service.

176

Electrical tools need to be grounded or double insulated.

177

Ground fault circuit interrupters must also be provided if the tool is connected to temporary power.

178

That includes an extension cord plugged into a permanent outlet.

179

And make sure that any power tool is disconnected from the outlet before you start changing attachments or making repairs.

180

One of the most important things to do

181

when you're using a skill saw is to adjust the base plate for the right thickness.

182

That way, you're less likely to have the saw kick back and hurt you.

183

If you're using an air compressor, you need to be sure that the hose connections are secured with a clip or tie wire.

184

Otherwise, hoses can pop off and you're not expecting it, and it's easy for someone to get hurt.

185

And if you're running gasoline-powered equipment, you need to be sure that you've got good ventilation, since it'll be putting out carbon monoxide,

186

which can be really bad or even fatal in a confined area.

187

And don't use a specialty piece of equipment, such as a laser or powder actuated tool, unless you have the proper training.

188

And while we're talking about electrical hazards, don't ever go to an electrical panel and start tripping breakers.

189

There may be someone on the other end of that circuit who could be injured, so don't start throwing switches unless you know exactly what you're doing.

190

Someone dies from a fire every three hours.

191

Most of the people die as a result of inhalation of hazardous fumes from burning materials.

192

If you're doing any kind of cutting, welding, or anything with an open flame, you need to have a hot work permit.

193

Those permits can be found in the J.E.

194

Dunn trailer.

195

All combustible materials must be removed within the vicinity of the work.

196

If materials cannot be removed, they must be covered with fire blankets.

197

A fire extinguisher must be available and a fire watch posted

198

while you're doing the work and for a minimum of 30 minutes after you're done.

199

Gasoline and other flammable liquids need to be stored in approved safety cans

200

and the cans have to be labeled so you know what's in them.

201

If you're fueling a piece of equipment it's got to be turned off and you can't be smoking while you're refueling it.

202

Oxygen and acetylene bottles need to be chained in an upright position away from any possible ignition source.

203

It doesn't matter if they're full are empty, they need to be treated the same.

204

Different gases must be separated and stored a minimum of 20 feet apart, or have a one hour firewall separating them.

205

You always need to know the location of the nearest fire extinguisher, and make sure that you can get to it, otherwise it doesn't do you much good when you need it.

206

Check the extinguisher to see if it is charged, but don't test it by squeezing the handle.

207

Once you start doing that, the pressure will bleed off and it won't work when you need it.

208

If If you need to use an extinguisher, remember the word PASS.

209

It stands for pull the pin, aim the nozzle, squeeze the handle, and sweep the nozzle across the base of the fire.

210

And unless it's a really, really small fire, the very first thing you should do is let other people know there's a fire.

211

Water can cause all sorts of problems.

212

What happens is that moisture can actually get into the materials, which can start mold growing.

213

And if that happens, it's a big problem.

214

First we clean it up, then we check all the finished materials, the drywall, trim or cabinets.

215

We have to be sure that there's not any water damage to the underlying material.

216

If you see wet or damaged material, tell your foreman.

217

Don't pretend that it's not there.

218

Otherwise, we may end up with mold starting to grow in the building.

219

We'd rather take out damaged material than risk a problem.

220

The bottom line is that water on the job site is bad.

221

it up or tell your supervisor when you see water that doesn't belong.

222

The exterior skin of a building will only function the right way if all the parts are properly installed.

223

If you see something like torn flashing, missing or damaged building paper or simply something that just doesn't seem right, stop your work and notify your supervisor.

224

We need to get it fixed before it's covered up, otherwise it's likely to cause problems later on.

225

Our housekeeping is the main cause of slips and trips on projects, so the last thing to do before we head home for

226

the day is to make sure we leave the job site as clean as possible.

227

You're responsible for keeping your job area clean.

228

Scrap, debris, trash, and anything else that might be a tripping hazard needs to be picked up and thrown in the trash, including anything that's on stairs,

229

scaffolds, ramps, walkways, and all other work areas.

230

And if you see trash in the wall cavities, ductwork, or other enclosed spaces, pick it up.

231

Don't leave it for someone to find later.

232

We prohibit discrimination against any employee on the basis of race, color, sex, religion, veteran status,

233

sexual orientation, national origin, age, disability, or handicap.

234

We will not tolerate harassment or intimidation in any form.

235

If you feel like you're being harassed, report it to any one of the site supervisors.

236

If somebody is using offensive language or catcalls towards other workers or people passing by the site, that's a problem and we want to know about it.

237

Our goal is to make sure that we all have the opportunity to succeed at work. So that's it.

238

That's a lot to remember.

239

But the most important thing is to think about what you're doing.

240

Focus on your work, ask for help when you need it, and keep an eye out on the worker next to you so that you can both go home safe.

241

We're almost done here, but there's one more thing we want you to see before you go to work.

✨ Video Öner

21 cümleler

Retired Navy SEAL Explains How to Prepare for Dangerous Situations | Tradecraft | WIRED

Business EnglishUniversity StudentsWorking Adults

156 cümleler

Professional Communication Skills [BUSINESS COMMUNICATION PRO]

Business EnglishWorking Adults

77 cümleler

SCOOP Safety Training [WIP] | CookieRun: Kingdom

Business EnglishUniversity StudentsWorking Adults

51 cümleler

Vol 3 - test 6 - section 2

TOEIC PrepBusiness EnglishWorking Adults

Bu dersin kelimeleri ve konuşma notları

Bu videoda gölgeleme çalışması için 241 cümle ve 3705 kelime var. Konuşma bölümü 19:18 sürüyor. Konuşmacı hızlı konuşuyor, dakikada yaklaşık 192 kelime; bu yüzden birbirine bağlanan ve zayıflayan sesler duyacaksınız. Kelimelerin %84’i İngilizcede en sık kullanılan 3.000 kelime arasında; geri kalanına başlamadan önce bakmakta fayda var.

Bu videodaki önemli kelimeler

Videodan öğrenmeye değer 15 kelime, telaffuzu ve anlamıyla:

Kelime	Telaffuz	Anlam
ladder isim	/ˈlæd.ɚ/	merdiven
climb fiil	/ˈklaɪ̯m/	tırmanmak
hazard isim	/ˈhæzəd/	risk, riziko
foreman isim	/ˈfɔː(ɹ).mən/	ustabaşı
installation isim	/ˌɪn.stəˈleɪ.ʃən/	kurulum, enstalasyon
supervisor isim	/ˈsupɚˌvaɪzɚ/	gözetmen
glove isim	/ɡlʌv/	eldiven
trench isim	/ˈtɹɛnt͡ʃ/	hendek
harness fiil	/ˈhɑɹ.nəs/	koşmak, koşum takmak
concrete sıfat	/ˌkɑnˈkɹit/	somut
tear fiil	/tɛɹ/	kırmak
waist isim	/weɪst/	bel
trash isim	/tɹæʃ/	çöp
dust isim	/dʌst/	toz
permit fiil	/pɚˈmɪt/	imkan yaratmak, fırsat vermek

Duyacağınız deyimsel fiiller

Kelime	Anlam
hang up fiil	asmak
put out fiil	çıkarmak
put together fiil	birleştirmek, bir araya getirmek
take out fiil	çıkarmak
turn off fiil	kapamak

Bu videodaki dil bilgisi

Konuşmacının en çok kullandığı yapılar, videodaki sözcüklerin aynısıyla:

Yapı	Videoda
Koşul cümleleri if + cümle, will/would + fiil — bir koşul ve sonucu	if you're cutting or welding, you'll need · if the soil gives way, you'll be
Edilgen yapı be + fiilin üçüncü hâli — kimin yaptığı değil, ne olduğu önemli	may be exposed · be exposed · will be required
Present perfect have/has + fiilin üçüncü hâli — geçmişte olan ama şimdi de önemli olan bir eylem	has been covered · has gotten damaged · has done
İlgi cümlecikleri who / which + cümle — bir kişi ya da şey hakkında ek bilgi	people who have · people who should · materials, which can

Dikkat edilecek telaffuzlar

Konuşmacı you're, don't, you've gibi kısaltılmış biçimleri 101 kez kullanıyor. Bunları duyduğunuz gibi kısa söyleyin.

“th” sesleri: thumb /ˈθʌm/, thickness /ˈθɪknəs/
“sh” ve “zh” sesleri: installation /ˌɪn.stəˈleɪ.ʃən/, trash /tɹæʃ/, inspection /ɪnˈspɛkʃən/, extension /ɪkˈstɛnʃən/, shield /ˈʃild/
Uzun kelimeler — vurguyu doğru yere koyun: installation /ˌɪn.stəˈleɪ.ʃən/, supervisor /ˈsupɚˌvaɪzɚ/, electrical /ɪˈlɛktɹɪkəl/, manufacturer /ˌmænjʊˈfæktʃəɹə/, temporary /ˈtɛmp(əˌɹ)ɛɹi/

Bu videoyla nasıl çalışılır

Videonun tamamını konuşmadan bir kez dinleyin ve bilmediğiniz kelimeleri not edin.
0,75× hızla başlayın, cümle cümle tekrar edin ve kolaylaşınca normal hıza dönün.
Kendinizi kaydedin ve orijinaliyle karşılaştırın; ladder, climb, hazard gibi kelimelere özellikle dikkat edin.

Gölgeleme Tekniği Nedir?

Gölgeleme, başlangıçta profesyonel tercüman eğitimi için geliştirilen ve çok dilli Dr. Alexander Arguelles tarafından popüler hale getirilen, bilim destekli bir dil öğrenme tekniğidir. Yöntem basit ama güçlüdür: ana dili İngilizce olan bir sesi dinler ve hemen yüksek sesle tekrar edersiniz — konuşmacıyı 1-2 saniye gecikmeyle takip eden bir gölge gibi. Pasif dinleme veya dilbilgisi alıştırmalarının aksine, gölgeleme beyninizi ve ağız kaslarınızı gerçek konuşma kalıplarını eşzamanlı olarak işlemeye ve yeniden üretmeye zorlar. Araştırmalar, telaffuz doğruluğu, tonlama, ritim, bağlı konuşma, dinleme anlama ve konuşma akıcılığını önemli ölçüde geliştirdiğini göstermektedir — bu da onu IELTS Konuşma hazırlığı ve gerçek dünya İngilizce iletişimi için en etkili yöntemlerden biri yapar.

Shadowing tekniği: adım adım eksiksiz rehberi okuyun →

Shadowing Practice: Construction Safety Training Video // Over 40 Topics - Learn English Speaking with Video

Dangers of a Negative Safety Culture

English for Doctors:Talking about a Head Injury

Why You Need To Train Your Ears First, Not Your Eyes | English Tips

Japan's construction sites beat summer heat | Vietnam Today

15 Common Health and Safety Interview Questions and Answers - Safety Training

How To Deal With Construction Delays

Reading Test 1. Seccion 2: Reducing Injuries on the Farm

Basic Introduction To Oil & Gas Well Perforating