Luyện nói tiếng Anh bằng Shadowing qua video: Making RAM at Home

RAM prices have been insane.

⏸ Tạm dừng

Tốc độ:

192 câu

Nếu các câu quá ngắn hoặc quá dài, hãy bấm Edit để chỉnh sửa.

RAM prices have been insane.

Driven by the rise in AI, it is causing massive disruption to the GPU, cell phone, PC markets, and more.

And a key reason it's been so bad is that you have just three companies,

Micron, Samsung, and SK Hynix, controlling the industry.

Where new supply is not something that can appear overnight, building new fabs can take billions of dollars and years of work.

So rather than wait around, I turned a shed in my backyard into a class 100 cleanroom and build my own semiconductor fabrication tools from scratch.

Now the question is, can I actually make my own RAM?

To start, how does RAM actually work?

If we take a look and we zoomed in to one of the chips on a sticker RAM,

where we would find our tens of thousands of rows and columns that make up an array,

where each intersection has a transistor and a charge storage capacitor.

The transistor acts as a switch, while the capacitor acts as a battery.

When I turn on the transistor, it switches on the current and charges up the capacitor, storing one bit of information.

I can then turn it off and hold the charge there.

If I want to then read the data, I switch on the transistor again and the charge now flows backwards out so it can be detected.

Though since that drains the capacitor, we have to refresh it and charge it back up periodically.

But to build anything, we first need a design.

I came up with a simple layout to have a 5x4 array that I could later stitch together,

where each intersection has a transistor and a capacitor.

I'm aiming for a small transistor, a gate length a bit less than 1 micron when finalized.

Each color here in this figure represents a different layer, like a different floor in a house, as these devices are made layer by layer by layer,

kind of like a sandwich.

Silicone is the starting material for making RAM.

Here I take a whole wafer and cleave it down to smaller workable chips.

With a diamond scribe, silicon nicely cleaves along certain crystal planes.

Kind of like a box with a bunch of 90 degree angles.

Now after cleaving, there may be some debris on the wafer,

so I use a solvent cleaning process with acetone and isopropanol alcohol.

This is meant to remove some of the particles off of

the surface as well as being able to dissolve any organics that may exist there.

It doesn't have to be perfect

because later on on our next step what we're going to

do is we're going to convert the surface from silicon to glass anyways.

The silicon chips are next loaded up into a furnace and heated to 1,100 degrees Celsius or 2,000 degrees Fahrenheit.

We're talking volcanic lava temperatures.

And this is in order to rust a silicon,

effectively growing 3,300 angstroms of oxide or glass on the surface in order to mask and protect it,

giving it this nice lime green color.

With a layer of glass now on our silicon chips, it can be a little tricky in order to coat different materials.

So I first apply lift off resist.

I coat that onto the surface.

Now this is normally meant, hence the name, for lifting off metal layers.

But I find it actually works fantastic as an adhesion layer.

This is then baked at 170 degrees Celsius for five minutes.

Now, photo resist, or photosensitive patternable film, can be easily spin coated and spun onto this adhesion layer.

After coating, it's baked at 100 degrees Celsius for two minutes to remove some of the excess solvent.

The photoresist uniformly forms a thin film of a silicon chips, which is a little bit thicker than one micron.

Photoresist acts as a patentable masking layer.

UV light is used in combination with a mask, where the mask only allows light to pass through designed openings and shine onto the photoresist, exposing it.

The UV light generates a photo acid, which when you take the sample and put it in a developer solution which is basic,

the acid and base neutralize each other, generating a salt which is dissolved away.

Basically, wherever you shine light, photoresist is now removed.

So you have photo resist everywhere except for where the UV light illuminated.

We use our first level from our design where the mask blocks light everywhere except for where our design is.

The microscope stepper system has objectives which then shrink this pattern down right to where our sample is going to be.

The higher magnifications further shrink that design down until you can't make out the sub-micron features.

We can see the design through the eyepieces and the camera, where custom software controls the focus and exposure.

The areas exposed to UV light are developed with our robot friend for better uniformity,

and ultimately removed, forming our patterned photoresist.

Using the photoresist layer as a mask, the patterned areas are dry-etched,

where we selectively remove that glass layer to get back down to the silicon surface.

With the edging step complete, we no longer need the photoresist mask.

So the photoresist is stripped in heated DMSO.

Weird enough, people actually take this as a form of medication.

But the semiconductor industry actually uses it as a strong solvent to remove photoresistant LOR.

So this leaves us with windows now in our 3,300 angstroms of oxide or glass on silicon.

We did this as the oxide itself acts now as a high temperature mask for our next step,

which it involves forming the source and drain of our transistor.

You can think of the source and drain as effectively the input and output terminals for our switch,

the gate or switchy part will be later formed in the middle.

We accomplish this by introducing dopants into the material in these windows here

and that makes these regions highly conductive input outputs and this is by adding phosphorus into the silicon.

So how in the world do we do that?

How do we add phosphorus into the silicon?

So there are a number of commercial products that do this.

The industry also makes use of ion implantation, but that is ridiculously expensive, and it's too large of a footprint for a shed.

So Projects in Flight actually made a fantastic video on this, making phosphorus-doped spin-on glass as opposed to buying it.

I tested the solution first on a test piece, where the initial wafer is so resistive that a multimeter can't easily detect continuity

but on a treated sample it is now highly conductive

and uh kind of working towards degeneratively dope a very high level of doping

which is perfect repeating this on our main chips we can coat the phosphorus dope spin on glass

and then we can proceed to bake it where the temperature

is ramped up slowly in order to drive out all the solvents but not cause undue stress or cracking.

It looks good, however there are a handful of glass precipitates that can form during synthesis.

While this shouldn't be an issue and it's mostly cosmetic, next time the better thing to do is to filter it in order to remove any glass precipitates.

I made a calculator in order to model effectively the depth of our phosphorus doping profile.

what's that going to look like?

Because what we want is that we want effectively a more shallow profile for what we're aiming for.

And to get

that, what we're going to do is we're first going to

anneal with the phosphorus dope spin on glass at 1100 degrees Celsius for five minutes.

Strip of the spin on glass in hydrofluoric acid and then do a drive-in anneal at 1000 degrees Celsius for 10 minutes.

With the source and drain, the input output electrical terminals for our switch,

for our transistor, we can now focus on the switch aspect itself, the gate region of our transistor.

LOR, lift-off resist, or makeshift adhesion layer, is then coated because we still have glass on the surface.

Followed by our photo resist layer, again that patternable layer.

We coat both of them again.

With these layers down, we can then pattern and form the channel region of our transistor.

To do that, we need this layer to be aligned between our previously formed source and drain regions.

100

While we're at it, we're also going to align and expose the area that will form our charge storage capacitor,

101

which is right above our transistors.

102

After development, an HFH is used to remove the middle oxide between the source and drain,

103

as well as next to the transistor for our charge storage capacitor.

104

This is because the oxide is too thick there and we want a custom oxide thickness for our gate and capacitor.

105

The channel region of our transistor, the thing that does our switching, is the most critical region.

106

As such, I perform a clean known as a piranha clean

107

which will viciously attack any organics and most metals on the surface.

108

They call it piranha as it can eat material

109

and flush just like a piranha fish in the Amazon going after a chicken leg.

110

The samples are loaded back into the furnace to grow the gate and capacitor oxides.

111

We want this thinner so we have more capacitance and better gate control.

112

So we're going to grow at a lower temperature of only 950 degrees Celsius.

113

And if we put it in there for 38 minutes, we get 200 angstroms, or 20 nanometers, of oxide.

114

This is what the structure looks like now, where we have our gate and capacitor oxides grown again at 20 nanometers,

115

where we still have thicker oxide outside of the device.

116

But because everything is covered in oxide, what we need to do is we need to punch some holes selectively through

117

that oxide in order to later form electrical contacts to the device.

118

More LOR and photoresist are coated and baked, and then the contact cut mask is carefully aligned and exposed,

119

where after development, we're left with some small openings in the LOR and photoresist.

120

HF or hydrofluoric acid is again utilized where

121

that can go into the photoresist and LOR openings in order to remove any glass on the silicon surface,

122

thereby forming a nice pathway for electrical connection.

123

For the final level in our device, we need to deposit metal to form the gate of our transistor electrical contacts,

124

as well as the capacitor itself.

125

To do this, LOR and photoresist are coated and baked, and then we can align and expose the final mass level.

126

Though this level is a bit different than our previous levels, where our previous levels were all focused on removing material.

127

With this, what we're doing now is that we're using the photoresist openings that we have

128

in order to treat them as a stencil combined with a metal deposition process.

129

A good analogy for this is that if we wanted to paint something, such as a handicap sign over here, what we might do is that we might use a stencil,

130

in this case a metal stencil, where we could deposit material by spray painting,

131

for instance, and then when we remove our stencil, we're just left with the design where we want.

132

Well, that's effectively what we're doing here at the nanoscale with the pattern that we've created.

133

But instead of spray painting, what we're actually doing is that we're effectively spraying the surface with metal atoms, in this case, aluminum here,

134

where the sample is loaded up into my sputter system, where we have argon that hits the metal target,

135

and then the metal atoms fall off and are effectively sprayed, so to speak, onto our sample.

136

So as you can see, the metal has been uniformly coated over the sample, except where there was some capped on tape at the edges there.

137

So how do we effectively remove our stencil?

138

How do we remove the photoresist layers here?

139

Well we can stick that in once again DMSO and heat that up.

140

It's always cool to see where we can start to see the metal buckle

141

and then eventually start to peel off of the surface.

142

If I apply a little bit of agitation there we can aid in its removal just leaving the pattern

143

that we want looking at it under the microscope post liftoff process what we can see is

144

that we can see our complete structure now we have the transistors the capacitors all the connections

145

that we need in order to have our DRAM array

146

if we were to look at a cross section this is the structure

147

that we have

148

and then this is how it matches up to our earlier little cartoon where we can have current flow

149

and be controlled by the transistor by our switch where it

150

can charge up our charge storage capacitor in order to hold a bit of data now as

151

if the shed wasn't enough inside in my living room i held a whole suite of test equipment

152

so i got my little lab assistant here

153

and i'm going to fire up one of these semiconductor parameter analyzes in order to look at the results.

154

Because these devices are of course at the nano scale, you can't just attach regular wires easily to them.

155

So for testing purposes, what I have set up here is

156

that I have a number of these micro manipulators with some

157

incredibly fine probe tips in order to feed electrical current

158

and voltage into the device and then be able to read that out.

159

When testing the transistor, our switch, I get the following results.

160

Each line represents a different gate voltage, where I can have different levels of current, or nearly no current depending on the gate voltage I apply.

161

This acts like our switch, or more specifically, it can act like one of those dimmer switches, where as I turn and adjust,

162

I can tune the level of output power.

163

But for RAM, we can just settle for basic on-off operation.

164

Normally, though, in a transistor, current saturates.

165

These lines stay flat.

166

It doesn't shoot up at higher voltages.

167

What we're seeing is a short channel effect known as punch-through.

168

So because the source and drain are less than one micron away from each other,

169

as we increase the voltage that we apply, they can effectively merge.

170

and this leads to an increase in current and a loss of gate control.

171

Now this is fine as long as we operate our devices at lower voltages, but it certainly shows the challenges of scaling.

172

So let's look at the other half of the equation, the charge storage capacitor that we have.

173

So here I have a CV plotter, which is a very sensitive instrument for reading up the capacitance as I

174

scan through and then vary the voltage across the capacitor

175

because the capacitor will have a minimum and a maximum capacitance of course in

176

which it can store and that maximum capacitance I recorded as 12.3 picofarads

177

which is pretty close to the perfect ideal theoretical of a little bit less than 15 picofarads

178

which I had designed for looking at them together now as one individual DRAM cell,

179

the transistor can very rapidly and quickly charge up our charge storage capacitor to 3 volts within a couple hundred nanoseconds,

180

which is great, and then it'll hold that voltage on there

181

but it'll slightly bleed off over time where we can only hold

182

that charge on there for a little bit over two milliseconds before it's completely done for.

183

We need to charge it back up if not sooner.

184

Commercial DRAM can hold its charge for greater than 64 milliseconds, so in this design it needs to be refreshed at a higher frequency.

185

Okay, this is awesome.

186

First time ever RAM has been made at home, but while you can store data on it, you can't run DOOM on it quite yet.

187

This is just a few cells to prove it can work.

188

The next step is to take these cells, to stitch them together in order to make a much larger array.

189

Then we can hook it up to a PC.

190

Stay tuned.

191

Massive thanks to everyone subscribed on Patreon who helped support this work.

192

Link below.

TRENDING

Phổ biến

Phương Pháp Shadowing Là Gì?

Shadowing là kỹ thuật học ngôn ngữ có cơ sở khoa học, ban đầu được phát triển cho chương trình đào tạo phiên dịch viên chuyên nghiệp và được phổ biến rộng rãi bởi nhà đa ngôn ngữ học Dr. Alexander Arguelles. Nguyên lý cốt lõi đơn giản nhưng cực kỳ hiệu quả: bạn nghe tiếng Anh của người bản xứ và lặp lại to ngay lập tức — như một "cái bóng" (shadow) đuổi theo người nói với độ trễ chỉ 1–2 giây. Khác với luyện ngữ pháp hay học từ vựng bị động, Shadowing buộc não bộ và cơ miệng phải đồng thời xử lý và tái tạo ngôn ngữ thực tế. Các nghiên cứu khoa học xác nhận phương pháp này cải thiện đáng kể phát âm, ngữ điệu, nhịp điệu, nối âm, kỹ năng nghe và độ lưu loát khi nói — đặc biệt hiệu quả cho người luyện IELTS Speaking và muốn giao tiếp tiếng Anh tự nhiên như người bản ngữ.

ShadowingEnglish.com – Luyện Nói Tiếng Anh Bằng Shadowing

Nói tiếng Anh lưu loát với phương pháp Shadowing — nghe người bản xứ, đọc theo từng câu, rèn phản xạ ngôn ngữ thật sự. Được hàng ngàn người học IELTS tin dùng.

Luyện nói tiếng Anh bằng Shadowing qua video: Making RAM at Home

Phổ biến

Ngữ Cảnh & Bối Cảnh

5 Cụm Từ Hữu Ích Cho Giao Tiếp Hàng Ngày

Hướng Dẫn Shadowing Từng Bước

Phương Pháp Shadowing Là Gì?

Luyện nói tiếng Anh bằng Shadowing qua video: Making RAM at Home

Tải Ứng Dụng

Ngữ Cảnh & Bối Cảnh

5 Cụm Từ Hữu Ích Cho Giao Tiếp Hàng Ngày

Hướng Dẫn Shadowing Từng Bước

Phương Pháp Shadowing Là Gì?