تدريب Shadowing: PCBs | Electronic Goods Reliability Testing - تعلم التحدث بالإنجليزية عبر الفيديو
جارٍ إنشاء الدرس...
1
Welcome to this next video in the series for PCBs.
2
Here we're going to be looking at electronic goods and the reliability testing.
3
Let's start with reliability and durability.
4
New product development is a complex process and takes time and a key step in the processes
5
testing your product for reliability and durability.
6
The main reason for reliability testing is to find out what the performance is over a long period of time.
7
Reliability test results may be categorized using the bathtub curve shown on the right here.
8
The bathtub curve shows the decreasing failure rate during the early infant mortality days of the product,
9
leading to the normal life of product population and finally the onset of the end-of-life wear out.
10
You can see here the decreasing failure rate section, the constant failure rate and the increasing failure rate.
11
The blue curve is the bathtub shape.
12
Let's switch over to temperature and humidity.
13
Temperature and humidity testing determines
14
how a system behaves in extreme conditions where the product is operated in high and low temperatures
15
as well as cycling the temperature between high and low.
16
Among other things, temperature
17
and humidity test studies the effects of climate changes on electronic components such as failures due to parameter shifts,
18
mechanical failures due to rapid water or frost formation, optical failures as in fogging,
19
water tightness in packaging and looking at the failures,
20
and material degradation or epoxy coatings etc and much more.
21
The table on the right here shows an example of shipping
22
environmental tests where it goes from step one to five and the humidity and temperature starts at low,
23
raising to high and then back down to low again.
24
On the right hand side it shows the duration for each of these tests.
25
RH just stands for relative humidity.
26
Vibration testing.
27
The applications of vibration testing form a major part of quality assurance for everything from printed circuit boards to completed products.
28
With specifically designed equipment such as mechanical,
29
electro-hydraulic and electromagnetic shakers, test samples are typically subjected to varying degrees of controlled vibration stresses.
30
Products are vibration tested to determine limits and tolerances.
31
Every product is vulnerable to vibration loads and potential breakage or failure.
32
You can see here, typical vibration test machine.
33
Mechanical shock testing.
34
The ability to withstand mechanical shock is both a key design consideration
35
and an important selling point for certain types of consumer goods.
36
For this reason, a dynamic mechanical analysis is a required component of quality control and product testing.
37
A shock test will measure the impact of sudden acceleration or de-acceleration using precise tools such as strain gauges,
38
load cells, and piezo sensors.
39
Here we can see a mechanical shock testing equipment and the setup.
40
Now I want to talk about the highly exaggerated life test or the HALT process.
41
HALT is applied to the initial product testing stages prior to production
42
and its primary objective is to highlight failure modes
43
and weaknesses in the design so the design can be modified and improved to eliminate any weaknesses found.
44
In HALT, temperature and vibration stress conditions
45
are used during product development to find weak spots in the product design and its planned fabrication processes.
46
Other test stimuli may include humidity, thermal cycling, burn-in for a specified period of time,
47
overvoltage, voltage cycling and anything else that could logically expose defects.
48
This test requires only a few units and a short testing period to identify the fundamental limits of the technology being used.
49
Generally every weak point must be identified and fixed or redesigned if it does not meet the product's specified limits.
50
This is a typical flow process for the whole process.
51
We can see at the top here we've got start we
52
then drop down into the first test cycle here we're looking at temperature operation limits with voltage limits.
53
We can see then if we've got the decision point, failure occurs or not.
54
If it does not occur, then it just drops into the next test cycle.
55
And here we've got the thermal cycle.
56
And again, the decision point there, if it does not fail, it completes the cycle with a vibration test.
57
If however, at any point during these tests,
58
the failure does occur, then you can see it drops down to the bottom, leading the requirement to analyze what that root cause was,
59
then moving into manufacturing process improvements, improvements from the design features,
60
improved component choice etc and then coming back through that complete cycle until everything has passed this process.
61
Next let's have a look at the highly accelerated stress screening or HAS.
62
HAS is implemented at the production stage where the production samples
63
are subjected to stress testing beyond the product specification limits but not up to the extreme levels used in the HALT test.
64
The objective of HAS is to ensure products from production meet the life expectancy without showing any signs of failure modes.
65
Early production failures on a new product are often attributed to
66
variability within the manufacturing process therefore identifying these potential production failure
67
modes as early as possible is paramount to the success of a product launch and this is where has comes into play.
68
A random set of production items will be selected for the production line
69
and then placed under different stress tests that can highlight production faults
70
that are not only obvious but will also identify any of the latent faults that are not detectable in normal production testing.
71
This reliability screening allows potential faults to be identified that are normally associated with early production failure in the field.
72
This provides the engineering team to work on corrective actions
73
and process improvements thus creating a more robust and reliable product that would otherwise lead to potential product failures for the customer.
74
In summary, this process is ideally suited to all electronic
75
and electromechanical assemblies so that a more reliable and robust product can be released into the marketplace.
76
Let's have a look at a quick graph for HAS.
77
On the extreme ends of the graph we have the lower and upper destruction limits.
78
The next set of limits in are the lower operational and the upper operational limits.
79
In the center here we have the has section and the production specification limits.
80
We can see that the manufacturing defects removed by the has testing highlighted in red.
81
This is the objective of the has testing to remove these poor products.
82
Let's have a look at the HALT and the has summary with a timeline.
83
We can see in In the table, across the top we have the typical test profile for both HALT and HALT,
84
the defects being addressed, development phase being applied and the stress levels.
85
From a timing point of view across the bottom, the HALT test is clearly shown in the design phase,
86
whereas the HALT test is highlighted at the end of the manufacturing phase.
87
The importance of product reliability.
88
You never get a second chance to make a first impression.
89
So making sure your products are reliable before you bring them to market can prevent problems that can doom your business.
90
Understanding some of the basic benefits of reliability testing will help
91
you make sure you're ready to sell with minimal problems from day one.
92
Making sure your product is reliable can also help you spot design
93
and production flaws that can cause failure and potential injuries to users.
94
Just one successful lawsuit can put you out of business.
95
Remember, put reliability first.
96
Don't forget to check out our other videos in this series
97
and you can contact us if you need any help with your projects at all in China.
98
Don't forget to like, share and subscribe to our channel.
99
For more information you can always visit our website and go to the solutions page.
100
Thanks for listening, my name is Paul Adams from South East and I shall see you in the next video.
📺 نفس القناة
C17
What is SMT (Surface Mount Technology)? PCB Assembly (Part 2)
Business EnglishUniversity StudentsWorking Adults
C1Sofeast PCB Video Series Introduction
Business EnglishUniversity StudentsWorking Adults
B22
DFM And DFA Explained
Business EnglishUniversity StudentsWorking Adults
C13
What is SMT (Surface Mount Technology)? PCB Assembly (Part 3)
Business EnglishUniversity StudentsWorking Adults
C14
PCB Inspection Methods & Common PCB Defects
Business EnglishUniversity StudentsWorking Adults
C13
NPI Process 1: Why A Pilot Run Before Mass Production Is Very Useful
Business EnglishUniversity StudentsWorking Adults
C15
What is SMT (Surface Mount Technology)? PCB Assembly (Part 1)
Business EnglishUniversity StudentsWorking Adults
B2BONUS: Should we do PCB or enclosure design first? (Feat Andrew Amirnovin)
Business EnglishUniversity StudentsWorking Adults
B2What are PCBs and PCBAs? The 'PCB basics'
University StudentsWorking Adults
B1Don’t Approve a Product Until You’ve Lived With It
Business EnglishWorking Adults
B1The Product Passed the Safety Test, But Was Still Too Hot to Hold
Business EnglishWorking Adults
B2The Product Worked, But the Packaging Made It Look Dead
Business EnglishWorking Adults
B2Why User Experience Is Harder Than Engineering
Business EnglishUniversity StudentsWorking Adults
C14 NPI Tips Before You Move Into Mass Production
Business EnglishWorking Adults
C1The Production Validation Test (PVT) Phase of the NPI Process
Business EnglishWorking Adults
C1The Three NPI Phases Explained
Business EnglishUniversity StudentsWorking Adults
C1When Can The NPI Process Begin?
Business EnglishUniversity StudentsWorking Adults
C1NPI Process #3: Why A Feasibility Study With Suppliers Saves Time & Prevents Issues
Business EnglishWorking Adults
C1NPI Process 2: New Product Development Process (Why Planning Before Prototyping Saves Time)
Business EnglishUniversity StudentsWorking Adults
✨ فيديو موصى به
C12
18 جمل
SD91: Reliability vs Scalability
Business EnglishUniversity StudentsWorking Adults
C12
119 جمل
How to Write Test Cases for Manual Testing?
Business EnglishUniversity StudentsWorking Adults
C14
28 جمل
Comparing Low Voltage Vs. Medium Voltage Equipment on Solar Sites
Business EnglishUniversity StudentsWorking Adults
C124 جمل
We Are AmSpec Group
Business EnglishUniversity StudentsWorking Adults
C13
84 جمل
What is the 8D report? (problem solving tools)
Business EnglishUniversity StudentsWorking Adults
C11
162 جمل
Introduction to PLC | Siemens PLC Training Course
Business EnglishUniversity StudentsWorking Adults
C167 جمل
The Ultimate IoT Roadmap in 2026? | Embedded Systems & IoT Career Roadmap
Business EnglishUniversity StudentsWorking Adults
C12
43 جمل
SDLC Vs STLC: Software Development Life Cycle and Software Testing Life Cycle
Business EnglishUniversity StudentsWorking Adults
C11
106 جمل
EDFR GWO BTT Training Center - Nicolas Riou Wind
Business EnglishUniversity StudentsWorking Adults
B21
362 جمل
Celpip Listening Mock Test - 1 | Celpip Listening Test Practice With Answers - 2026
TOEFL PrepTOEIC PrepBusiness English
لماذا يجب ممارسة المحادثة مع هذا الفيديو؟
تعتبر ممارسة المحادثة من العناصر الأساسية لتطوير مهارات اللغة الإنجليزية، ويقدم هذا الفيديو فرصة ممتازة للاطلاع على مواضيع متقدمة في اختبار موثوقية السلع الإلكترونية. من خلال الاستماع إلى الحوار، يمكنك تحسين قدرتك على التعبير عن الأفكار المعقدة وفهم المفاهيم التقنية. ستساعدك هذه الممارسة على بناء ثقتك في استخدام اللغة الإنجليزية في سياقات مهنية وعلمية. كما أن "ممارسة المحادثة الإنجليزية" ستعزز من قدرتك على التفكير باللغة الإنجليزية، مما يجعلك أكثر طلاقة في التحدث.
القواعد والتعابير في السياق
يتضمن الحوار العديد من الهياكل اللغوية والتعابير المفيدة. إليك بعض النقاط المهمة:
- التعبير عن التقييم: يستخدم المتحدث عبارات مثل "الهدف الرئيسي هو" لتوضيح الأهداف، مما يساعد على تحديد الأولويات أثناء المناقشة.
- استخدام الجمل الشرطية: توجد جمل مثل "إذا تم استخدام...، فسوف نرى..." لشرح النتائج المتوقعة، وهو نمط مهم لفهم الظروف والنتائج.
- التشديد على النقاط الهامة: عبارة "من الضروري أن" تُستخدم لتسليط الضوء على أهمية اختبار موثوقية المنتجات، مما يجعل الرسالة أكثر تأثيراً.
هذه الهياكل تعزز من قدرتك على التواصل بوضوح، وهو أمر ضروري في بيئات العمل.
فخاخ النطق الشائعة
تتطلب بعض الكلمات والعبارات انتباهاً خاصاً عند نطقها. على سبيل المثال:
- كلمة "موثوقية": ينصح بممارسة نطق هذه الكلمة بشكل صحيح، حيث أن النطق الخاطئ قد يؤدي إلى سوء فهم.
- التعبير "فحص الاهتزازات": يجب الانتباه لجعل النطق واضحاً، حيث أن الكلمات المركبة يمكن أن تكون صعبة على السمع.
تعتبر "shadow speak" وسيلة فعالة لمساعدتك في تجاوز هذه الفخاخ من خلال الممارسة المستمرة، مما يجعلك أكثر كفاءة في التحدث.
ما هي تقنية التظليل الصوتي؟
التظليل الصوتي (Shadowing) تقنية تعلم لغة مدعومة علمياً، طُورت أصلاً لتدريب المترجمين الفوريين المحترفين. الطريقة بسيطة لكنها قوية: تستمع لصوت إنجليزي أصلي وتكرره فوراً بصوت عالٍ — كظل يتبع المتحدث بتأخير 1-2 ثانية. تُظهر الأبحاث تحسناً كبيراً في دقة النطق والتنغيم والإيقاع وربط الأصوات والاستماع والطلاقة.