Shadowing Practice: How to Fix Holes in Drywall - 4 Easy Methods - Learn English Speaking with Video
Bir pratik modu seçin
Her mod tam ekran bir pratik odası açar.
268 cümleler
Cümleler çok kısa veya çok uzun ise, ayarlamak için Düzenle'ye tıklayın.
1
Hi there, I'm Nils with Learn2DIY and sometimes bad stuff happens to your drywall.
2
So today we're going to cover all of these types of damage
3
and we're going to show you how to fix each one of them.
4
Now, just about every hole that you'll find in drywall falls into one of four types.
5
Basically, you've got something that's really small, like an inch, inch and a half or smaller,
6
maybe that's two and a half, three centimeters and that's something
7
that we can patch a certain way up from there you got anything between
8
that size and maybe fist size four or five inches or
9
so and then from there you've got something that's big enough
10
that it's in between your studs or maybe it's even over a stud
11
but it needs some support so we're talking stuff that's about this big
12
or smaller maybe seven eight inches nine inches in that range
13
and then lastly we've got some major damage like what we showed over here
14
and this is just going to need to have a whole section replaced.
15
So those are the four types we're going to cover.
16
And with those four types, we're going to show you the best and quickest way to handle each of those.
17
And then I've put chapters below so you can actually skip ahead to the section that matches your situation best.
18
And then with that, we'll show you how to do the patches for each one.
19
And then at the end of the video,
20
I'll show you how to match that texture and make it look smooth and just like the wall was before,
21
whether you've got orange peel or a Santa Fe or knockdown or a completely smooth wall.
22
Now to start off with we had this really small hole right over here
23
that was about an inch and then we had another one in this lower left corner
24
and with something like that anything that is about an inch
25
or so maybe two and a half centimeters or so and smaller you can actually just patch that just with mud.
26
You don't really need tape you don't need a patch kit necessarily
27
and you can use those things but they're not going to help a whole lot
28
because it's such a small hole it should be easy enough to work with.
29
With that, what you're going to do is take some mud
30
that you get at the store and you can buy this in this larger bucket like this for about $6.
31
They're actually really inexpensive.
32
You can also buy powder that you mix up yourself
33
or you can buy a really small container if you just have a small hole like that.
34
Now with that, you're going to use a putty knife.
35
I would recommend using one that's at least three or four inches in width and with the knife like that,
36
a mud knife, you're just going to take it and we're going to fill in that hole as best we can.
37
You want to be pretty generous in pushing that mud back into
38
that hole to make sure that it's really backfilled
39
and there's plenty in there so that it's nice and strong when it dries.
40
Now on the first coat, you're going to have some bubbling.
41
It's going to bulge out a little bit.
42
It's not going to want to stay in place really well, and that's okay.
43
We're going to just put that in there as well as we can, cover it up, and then we'll let that sit.
44
Now with this fist size hole that we've got over here, there's a few ways that you can tackle this.
45
I'll show you all three and two of them are very similar.
46
With the first one, you can buy a large patch that's a mesh adhesive patch like this one here.
47
We can actually just apply this eight by eight patch over the whole thing.
48
And the goal here is really simple.
49
We're going to clean up our edges, make sure it looks good.
50
And then we're going to smooth
51
that patch out as best we can to make sure there's no creases or wrinkles or any issues with that patch.
52
And it's nice and smooth.
53
And then we're going to take our mud and we're going to fill
54
that in and push a lot of that mud into the area
55
that has the hole in it and you can see from the back here
56
when you push mud in through these patches like this it's kind of a play -doh fun factory effect
57
and that's what we want we want to get a lot of
58
that back there to rebuild that drywall that's back behind there
59
and once we've got
60
that filled in really nicely through the area behind the patch
61
then we're gonna cover up the whole patch itself using
62
that same knife and our goal here is just to get it nice
63
and clean it doesn't have to be perfect we just want it to look really good and cover up everything that's there.
64
So that's option number one for your first coat.
65
Option number two is what's called the Presto Patch.
66
The Presto Patch is a really simple idea.
67
Basically it's a four inch circle of half inch drywall
68
and then it's got a larger section of paper that we'll use to blend that in with the surrounding wall.
69
So the idea with this one is you take the styrofoam that came with it, it's a template, you trace out your template with pencil
70
and then we're going to cut that out with a knife
71
and get that circle just the right size to match that Presto Patch.
72
Now once we've got that circle cut out, we're going to liberally apply mud all around the inside of the circle as best
73
you can also apply it around the outside of the circle where the paper goes.
74
And then don't forget to apply it also to the plug itself.
75
So you'll want to apply that mud liberally to the patch itself, especially on the top of it,
76
of that circle where some of the gravity will have pulled it down from the hole in the wall.
77
And then we're going to push that in.
78
And from there, we're going to use our knife to pull across.
79
We're going to pull from the center outward
80
and we're going to smooth all of that mud out from underneath the paper
81
and try to get that nice and smooth and matching up with the contour of the wall again.
82
Now, just like before we want to cover it enough
83
that it's covering everything there and we're not going to have anything peeking through,
84
but not so much that it's going to take two years to dry where we're going to have to sand for eternity.
85
Now the third technique that we can use for a hole like this is we can use what's called a California patch.
86
Now with that, we're doing the same thing that we saw with the Presto patch,
87
but this time we're actually cutting our own essentially out of drywall.
88
The first step in doing something like this is cutting out
89
a square as big as it needs to be to get good, strong drywall all around it.
90
So anything that's been roughed up or broken, especially on that backside, we want to cut that out
91
and make that square as big as it needs to be to where
92
We've got good solid drywall there.
93
So I'm using a square about this big here.
94
I'm going to clean up my edges and make sure it looks decent.
95
Then I'm going to use a piece of drywall.
96
I'm going to cut a piece that's about an inch and a half bigger on all sides than that square.
97
So let's say this was a five by five.
98
Then we want to cut a piece of drywall.
99
That's about eight by eight.
100
That leaves us with that inch and a half all the way around.
101
Now, once you've got that piece, you can hold the piece right up to the wall,
102
use your knife to score a line all the way down one side
103
and all the way down the inside that's just a little bit smaller than the hole.
104
Now we're going to flip it to the other side for the height and do the same thing.
105
We're going to have that square in the middle that's going to keep there and end up being our plug.
106
From there you're going to snap off and then you're going to peel everything but that front paper off.
107
So you're going to get all the gypsum and
108
that back paper removed on all four sides so
109
that you end up with a plug like this just like the presto patch
110
but one that we made ourselves
111
and then from there the technique is exactly like what we showed with the presto patch
112
we're gonna line the outside of this
113
and the inside of the hole with mud
114
we're gonna line mud all over the inside of the patch itself i'm gonna push
115
that in after we've got the right fit
116
and we've dry fitted it to make sure it works okay
117
we're gonna smooth out all the mud from all of the paper.
118
And then we're going to cover the whole thing in its first coat.
119
Now the only difference between the second type of hole and the third type of hole in your drywall is backing.
120
If it's a little bit bigger, if it's anything bigger than about fist size, I would recommend that you put some backer boards on it.
121
And this technique is really simple.
122
You just need a couple of scraps of wood.
123
Could be anything.
124
Plywood works really well because it doesn't split very easily, but you can use some leftover MDF, some trim,
125
just some one by pine that you have lying around anything will work pretty well
126
and what you want to do is cut it so
127
that it extends out a couple of inches past the width of the hole on both sides
128
or the height whichever way you want to go it doesn't matter
129
if you put these horizontally or vertically really
130
but our goal is to provide four corners for the patch to screw into
131
and then those four corners are supported by screws into the drywall around it
132
so we're going to drive some screws with these boards here we're going to drive them right into the board
133
and have that pucker the board right up tight against the drywall
134
and then once i've got those two boards in i end up with a nice area
135
and support for my patch to go into now a fix
136
like this you can actually go fairly large on this
137
if you've got a 10 inch hole for example then it can cover something like
138
that pretty easily as long as you've got that support
139
and you've cleaned up your square and you've got made sure that you've got good drywall to work with.
140
What you don't want to do is kind of go skimpy on the size of the hole
141
that you cut for this and then have weak drywall to work with around it
142
because this depends on the strength of the drywall surrounding the hole that you've cut out.
143
Now our fourth type of hole is the largest thing.
144
That's where there's a lot of damage.
145
Somebody body checked the whole wall or something like that
146
or got thrown into it and you've got a large amount of damage here and it's pretty beat up.
147
With that what I would recommend doing every time is just cutting it out from stud to stud.
148
You're going to need a stud finder
149
that you can rely on to find exactly where the studs are and then you're gonna mark those on your wall.
150
Once you have those studs marked you can use a jab saw or drywall saw.
151
You can also use a knife for this like a box cutter like we've been using
152
but a jab saw makes quick work of this and we're gonna cut from stud to stud.
153
We're also going to cut right down along the inside of the two studs where we're working.
154
So now that we know exactly where the inside of the studs are, we want to come over about three quarters of an inch
155
or about half the thickness of the stud
156
and we're going to use a knife and we're going to open that section up.
157
The goal here is to have a lip
158
or a secure area for the new piece of drywall that we're going to put in to sit on.
159
We're going to actually have it span from stud to stud
160
and it will then be able to use those studs to fasten in
161
and hold in place really well now just like with the california patch
162
we could create a large california patch here to fit in this area
163
but i'm going to show you how to do this with mesh tape instead
164
which is a very common method for a larger area like this
165
so basically we're going to fasten this new piece in we're going to use our drywall screws
166
and drive it in we're going to apply some of our yellow adhesive mesh tape
167
we're going to apply one piece on each side try not to overlap them
168
because that just adds to the thickness of the of the covering that we have to do.
169
And then use your knife to tear it.
170
It makes a nice straight line.
171
It's really easy to work with.
172
And once we've got all four sides covered up there, then we're just going to apply mud just like before into those seams.
173
We're going to push that in.
174
And from the back, you can see what this looks like.
175
We're really just pushing that mud really thick into
176
that area to try to cover as much of that half inch section or five eighths inch section as we can.
177
So we're going to just cover this all up so that you can't see the tape anymore.
178
Again, it doesn't have to be perfect on the first coat.
179
And we're going to do our best to get it nice and covered.
180
We'll come back the next day and the next day we can go through and sand this.
181
And you can do this with a hand sanded sponge like this guy here, or you can do this with a orbital sander for example
182
or a palm sander if you have one
183
but make sure to wear proper respiration this is going to kick a lot of dust up
184
so make sure that your lungs are protected i would recommend some goggles
185
or safety glasses as well
186
so our second coat we are going to use a larger knife
187
and i'm going to try to cover that up
188
and smooth everything over after it's been sanded so we'll put
189
that second coat on we call it a skim coat
190
and what i also recommend doing there is mixing up some water into your pan.
191
So if you have a mud pan, if you don't, you can use something similar to it.
192
But mud pans are awesome because they have a blade on either side to scrape that extra mud off of.
193
And it gives you a nice clean blade every time you use it or a nice clean knife.
194
So we're going to use that and we're going to skim across here and we're going to get this nice and covered.
195
And hopefully it ends up with a pretty smooth finish.
196
Now, depending on if you're working with kind of a knockdown style
197
or Santa Fe style texture on your wall versus an orange peel, you might end up with some,
198
you know, high spots and low spots and things like that.
199
But again, the goal is just to get it as smooth as we can.
200
I'm going to feather on that outside, feather on this outside, same with the top and the bottom,
201
creating a nice, smooth transition.
202
and then one down the middle.
203
There we go.
204
Okay.
205
And that makes all the difference having a good blade.
206
It really does help.
207
So if you can get one, these things are pretty cheap too.
208
I think they're usually around 10 bucks for a metal blade like this.
209
I've been using this one for years and it works well.
210
Now, depending on how that comes out with that second coat, you might need to come back and sand it into a third coat,
211
or maybe it's looking good at that second coat
212
and you're ready to place texture now no matter what size the patch was
213
that we had to take care of on the wall you want to make sure to use something
214
that matches the texture afterward so
215
if you've got an orange peel sort of texture on your wall
216
and you finish it smooth it's going to look like it was patched same with
217
if you do the opposite now they do sell different textures
218
that you can purchase you can buy these online
219
and i'll put links in the description below they come in different size cans
220
and there's different ways to do it but i'll put some of my favorites
221
and then you can also stop at the local hardware store and pick up this wall texture in a can.
222
They've got orange peel like you see here and then they also have a knockdown variety.
223
Now with both of these you've got different settings.
224
You can move this tab from side to side to adjust the pressure
225
that it sprays and then you can twist this knob here to adjust the coarseness or fineness of the spray.
226
So you might want to experiment on a piece of cardboard
227
or an unseen area just to make sure that you're not trying this out for the first time on your actual wall.
228
And then you can just spray it in circular motion like this
229
and this actual spray is in bad shape for whatever reason
230
it's not spraying out very well typically it will spray a little bit better than this
231
but you get the idea so we're gonna cover that up
232
and then you'll end up with a hopefully a decent matching orange peel texture now
233
if you don't have orange peel but you have something more like the Santa Fe
234
or knockdown texture and you can recognize that by how it has some areas
235
that are raised and some
236
that are lowered it looks kind of like this kind euro texture going on to it it's very traditional
237
it's been around for a long time so if you have
238
that texture you can also buy some knockdown texture in a can
239
and just here is very similar you're going to spray it in kind of a random pattern around the area
240
that needs to be treated and then you're going to use a 10
241
or 12 inch knife and pull across it really evenly
242
and your goal is to leave this as smooth as possible you don't want any little streaks
243
or cuts or scrape marks in there or anything like that, because this is kind of the final coat that you're going to be doing.
244
Now, if you don't want to use the can,
245
you can also just use this by hand with some mud and just dab some mud on here in different areas, kind of randomly.
246
You want to make sure to not make it look like it's in rows or lines or anything like that.
247
So keep that as random as possible.
248
And then just like before, you're going to take your 10 or 12 inch knife and pull it across.
249
Go in various directions if you need to, to try to get that nice smooth finish to it.
250
And if you have a good blade, a metal blade makes it so much easier.
251
I've tried this with the plastic ones and they don't really do very well.
252
But with that metal blade, you can pull that across and get a really good texture.
253
And your goal is to leave some of the areas a little lower, some a little higher.
254
So you have that knockdown or Santa Fe look to it.
255
Now, the last thing to do is just paint.
256
So make sure that you get all of the dust off there.
257
This stuff can be really porous.
258
It can really soak up a lot of that paint,
259
but you don't want to end up with a lot of dust on your roller while you're doing this.
260
And as you can see here, this wall that was full of holes just a couple of days ago.
261
is now patched up and looks good.
262
Now one tool that was really helpful on these larger patches, especially like this one up here, is a good stud finder.
263
Knowing exactly where that stud is, having an accurate representation of that.
264
I did a video a little while ago on several different stud finders compared.
265
We did the stud finder showdown.
266
So if you want to check that out and see which one works best for you, you can click on that link right up there.
267
Thanks for watching.
268
I'm Nils, and we'll see you on the next one.
Uygulamayı İndir
Akıcı konuşmak için ihtiyacınız olan her şey
AI TelaffuzHer cümleyi puanla
IPA AlıştırmasıHer sesi ustalaştır
Kelime BilgisiKelime bankanızı oluşturun
Kelime OyunuOynarken öğrenin
FOR YOU
Video Öner
B11
67 cümleler
Drywall Patching Secrets for Beginners
Daily ConversationWorking Adults
![Fixing a gate and draining paddocks [Life in New Zealand season 2 #502]](https://img.youtube.com/vi/vb1uw7iNzyA/mqdefault.jpg)
B12
71 cümleler
Fixing a gate and draining paddocks [Life in New Zealand season 2 #502]
Daily ConversationWorking Adults
B11
146 cümleler
How to Stop Tinnitus in 30 SECONDS
Daily ConversationWorking Adults
B11
735 cümleler
TỰ HỌC MAKEUP TỪ A-Z TRONG 30 PHÚT ! Hướng dẫn chi tiết từng bước một cho bạn lên trình makeup !
Daily ConversationWorking Adults
B11
121 cümleler
How To Make Any Room Actually Cool
Daily ConversationWorking Adults
B21
10 cümleler
HOW TO STRIP A CABLE using pliers as an electrician
Daily ConversationWorking Adults
B11
318 cümleler
How to Knit The Knit Stitch for Beginners | The Garter Stitch | PassioKnit Kelsie
Daily ConversationWorking Adults
B11
64 cümleler
How to Install a Dimmer Switch in 10 Minutes | Builds By Maz
Daily ConversationWorking Adults
B21
114 cümleler
How To Learn To Fix Cars (Beginner’s Guide)
Daily ConversationWorking Adults
B21
29 cümleler
How the Grand Canyon Was Really Carved?
Daily ConversationWorking Adults
B22
192 cümleler
How to Harvest, Condition, and Store Tulips // Dry Storing Tulip Flowers with Visuals // Northlawn
Daily ConversationWorking Adults
B11
97 cümleler
Client Aftercare For Lash Extensions | 10 Tips |
Daily ConversationWorking Adults
Bu dersin kelimeleri ve konuşma notları
Bu konuşma dersi “How to Fix Holes in Drywall - 4 Easy Methods” videosuna dayanıyor. En çok tekrarlanan kelimeler: patch, mud, hole, stud, drywall. Bu videoda gölgeleme çalışması için 268 cümle ve 3606 kelime var. Konuşma bölümü 15:37 sürüyor. Konuşmacı hızlı konuşuyor, dakikada yaklaşık 231 kelime; bu yüzden birbirine bağlanan ve zayıflayan sesler duyacaksınız. Kelimelerin %86’i İngilizcede en sık kullanılan 3.000 kelime arasında; geri kalanına başlamadan önce bakmakta fayda var.
Bu videodaki önemli kelimeler
Videodan öğrenmeye değer 15 kelime, telaffuzu ve anlamıyla:
| Kelime | Telaffuz | Anlam |
|---|---|---|
| patch isim | /pæt͡ʃ/ | yama |
| stud isim | /stʌd/ | damızlık |
| knife isim | /ˈnaɪ̯f/ | bıçak |
| coat isim | /ˈkoʊ̯t/ | palto |
| blade isim | /bleɪd/ | ağız |
| spray isim | /spɹeɪ/ | serpinti, çisenti |
| peel fiil | /piːl/ | soymak |
| sand isim | /sænd/ | kum |
| technique isim | /tɛkˈniːk/ | teknik |
| dust isim | /dʌst/ | toz |
| plug isim | /plʌɡ/ | fiş |
| fist isim | /fɪst/ | yumruk |
| mesh isim | /mɛʃ/ | gözenek |
| decent sıfat | /ˈdiː.sənt/ | uygun, onat |
| width isim | /ˈwɪtθ/ | genişlik, en |
Duyacağınız deyimsel fiiller
| Kelime | Anlam |
|---|---|
| get over fiil | üstesinden gelmek, yenmek |
Tekrar etmeye değer cümleler
Videodan, günlük konuşmada yeniden kullanabileceğiniz kısa ve tam cümleler:
- We've got good solid drywall there.
- Then I'm going to use a piece of drywall.
- We're going to push that in.
Bu videodaki dil bilgisi
Konuşmacının en çok kullandığı yapılar, videodaki sözcüklerin aynısıyla:
| Yapı | Videoda |
|---|---|
| Present perfect continuous have/has been + -ing — önceden başlayıp hâlâ süren bir eylem | we've been using · I've been using |
| Edilgen yapı be + fiilin üçüncü hâli — kimin yaptığı değil, ne olduğu önemli | been roughed · is cut · are supported |
| Present perfect have/has + fiilin üçüncü hâli — geçmişte olan ama şimdi de önemli olan bir eylem | I've put · that's been roughed · you've cleaned |
| “might / may” ile olasılık might/may + fiil — mümkün ama kesin olmayan bir şey | might end · might need · might want |
Dikkat edilecek telaffuzlar
Konuşmacı we're, you're, you've gibi kısaltılmış biçimleri 143 kez kullanıyor. Bunları duyduğunuz gibi kısa söyleyin.
- “th” sesleri: smooth /smuːð/, width /ˈwɪtθ/, thickness /ˈθɪknəs/, feather /ˈfɛðə/, thick /θɪk/
- “sh” ve “zh” sesleri: mesh /mɛʃ/, transition /tɹænˈzɪʃ.ən/, essentially /ɪˈsɛnʃəli/, representation /ˌɹɛp.ɹə.zɛnˈteɪ.ʃən/, respiration /ɹɛspɪˈɹeɪʃən/
- Uzun kelimeler — vurguyu doğru yere koyun: necessarily /ˌnɛs.əˈsɛɹ.ə.li/, essentially /ɪˈsɛnʃəli/, experiment /ɪkˈspɛɹ.ə.mənt/, representation /ˌɹɛp.ɹə.zɛnˈteɪ.ʃən/, eternity /əˈtɜɹnəti/
Türkçe konuşanların zorlandığı sesler:
- /w/ — dudaklar yuvarlak, /v/ değil: width /ˈwɪtθ/, afterwards /ˈæf.tɚ.wɚdz/, hardware /ˈhɑɹdˌwɛɹ/, twist /twɪst/, whichever /wɪt͡ʃˈɛvɚ/
- Kelime başındaki ünsüz kümesi — araya ünlü eklemeyin: stud /stʌd/, smooth /smuːð/, blade /bleɪd/, spray /spɹeɪ/, plug /plʌɡ/
- /æ/ — “e”den daha açık: patch /pæt͡ʃ/, sand /sænd/, transition /tɹænˈzɪʃ.ən/, afterwards /ˈæf.tɚ.wɚdz/, pan /pæn/
Bu videoyla nasıl çalışılır
- Videonun tamamını konuşmadan bir kez dinleyin ve bilmediğiniz kelimeleri not edin.
- 0,75× hızla başlayın, cümle cümle tekrar edin ve kolaylaşınca normal hıza dönün.
- Kendinizi kaydedin ve orijinaliyle karşılaştırın; patch, stud, knife gibi kelimelere özellikle dikkat edin.
Gölgeleme Tekniği Nedir?
Gölgeleme, başlangıçta profesyonel tercüman eğitimi için geliştirilen ve çok dilli Dr. Alexander Arguelles tarafından popüler hale getirilen, bilim destekli bir dil öğrenme tekniğidir. Yöntem basit ama güçlüdür: ana dili İngilizce olan bir sesi dinler ve hemen yüksek sesle tekrar edersiniz — konuşmacıyı 1-2 saniye gecikmeyle takip eden bir gölge gibi. Pasif dinleme veya dilbilgisi alıştırmalarının aksine, gölgeleme beyninizi ve ağız kaslarınızı gerçek konuşma kalıplarını eşzamanlı olarak işlemeye ve yeniden üretmeye zorlar. Araştırmalar, telaffuz doğruluğu, tonlama, ritim, bağlı konuşma, dinleme anlama ve konuşma akıcılığını önemli ölçüde geliştirdiğini göstermektedir — bu da onu IELTS Konuşma hazırlığı ve gerçek dünya İngilizce iletişimi için en etkili yöntemlerden biri yapar.