Pratica di Shadowing: What is SMT (Surface Mount Technology)? PCB Assembly (Part 2) - Impara a parlare inglese con i video
Scegli una modalità di pratica
Ogni modalità apre una sala di pratica a schermo intero.
60 frasi
Se le frasi sono troppo corte o troppo lunghe, clicca su Edit per modificarle.
1
Welcome to this video where we're going to be looking at what is an SMT
2
and this is using the surface mount technology to assemble PCBs part 2.
3
So here we're going to be looking at the PCBA production process.
4
We're going to be focusing on these next two elements within the process.
5
So there's reflow soldering process and the cleaning process.
6
So let's start with the reflow soldering process.
7
The circuit board assemblies need to be preheated to activate the flux in the solder paste.
8
Then they need to be heated at a higher temperature to reflow the solder.
9
A cooling step follows that allows a solder to solidify.
10
The The preheating, heating and cooling down cycles in the reflow machine are defined by the thermal profile.
11
We'll have a look at that in more detail in the following slides.
12
Let's have a look at the cleaning process.
13
So the PCB cleaning is the process of removing solder flux residues from the PCB after the SMT process.
14
The flux present in the solder paste reacts with the metal oxide during the reflow process
15
and prevents further oxidization of the solder metal.
16
The byproduct of this reaction is the solder flux residue that gets trapped beneath components and near the undersides of solder balls.
17
Let's have a look at the reflow thermal profile.
18
We're going to break this down into the separate zones.
19
So to start with we have the preheat zone.
20
The highest temperature is 2.5 degrees centigrade per seconds in the preheat area.
21
Over rising rate will cause solder balling.
22
In this image we have the recommended reflow soldering temperature profile.
23
We'll be focusing on this throughout this thermal profiling overview.
24
The next zone we're going to be focusing on is the soak zone.
25
Here we need to keep the temperature within a range of 150 to 210 degrees centigrade
26
and the temperature rise rate under 2.5 degrees centigrade per second during the soak zone
27
which lasts regularly from 60 seconds to 90 seconds and again we can see that here in this temperature profile.
28
The next zone is the reflow zone.
29
The peak temperature in the reflowing zone changes in the range of 230 to 255 degrees centigrade.
30
Temperature stays above 217 degrees centigrade for 40 to 70 seconds.
31
You can see this peak temperature here.
32
The final zone is the cool down zone.
33
The temperature dropping rate during cool down zone should be kept under 4 degrees centigrade per second.
34
Note the curve varies according to the shape of the plate and function of the devices.
35
The circumstance parameter is suggested to be 25 plus or minus 2 degrees centigrade by temperature,
36
and 45% and 65% by humidity.
37
You can see the overall time in this profile is around 270 seconds.
38
Let's switch over to the importance of cleaning.
39
Cleaning the PCB.
40
The solder flux residue, which is trapped between the components of the PCB substrate and the near underside of the solder balls,
41
is electrically conductive, as it is made up of ions.
42
As PCBs and modules are subjected to an external electric field,
43
the diffusing flux residue particles get excited by the momentum transfer of the conducting electrons in the circuit.
44
This leads to the particles getting displaced from their position.
45
A problem may arise when these particles cause bridging between two parts of the circuit.
46
This problem is known as electro migration.
47
Now the best practice, let's have a look at that.
48
Now there is a no clean solder paste available.
49
If possible you should be using this.
50
So many of the best performing lead free and lead containing solder pastes today are no cleans.
51
They have been designed to solve assembly problems described previously.
52
For the vast majority of applications the small amount of residue left by non-clean is not a problem.
53
However some assemblers want the performance of no cleans
54
but need to clean the no clean residue as they have extreme reliable or cosmetic requirements.
55
You can see how clean this no clean solder is in this image here.
56
So don't forget to check out our other videos in this PCB series
57
and you can contact us if you need any help with your projects at all in China.
58
So don't forget to like, share and subscribe to our channel and if you hit this little bell symbol
59
that will notify you each time we upload new content.
60
So thanks for listening my name is Paul Adams from I'm SoftEast and I shall see you in the next video.
Scarica l'app
Tutto ciò che serve per parlare fluentemente
Pronuncia con IAVoto per ogni frase
Pratica IPAPadroneggia ogni suono
VocabolarioCostruisci il tuo lessico
Gioco di vocabolarioImpara giocando
Stesso Canale
B2Sofeast PCB Video Series Introduction
Daily ConversationWorking Adults
C12
DFM And DFA Explained
Daily ConversationWorking Adults
C13
What is SMT (Surface Mount Technology)? PCB Assembly (Part 3)
Daily ConversationWorking Adults
C14
PCB Inspection Methods & Common PCB Defects
Daily ConversationWorking Adults
C13
NPI Process 1: Why A Pilot Run Before Mass Production Is Very Useful
Business EnglishWorking Adults
C15
What is SMT (Surface Mount Technology)? PCB Assembly (Part 1)
Business EnglishUniversity StudentsWorking Adults
B2BONUS: Should we do PCB or enclosure design first? (Feat Andrew Amirnovin)
Business EnglishUniversity StudentsWorking Adults
B2What are PCBs and PCBAs? The 'PCB basics'
University StudentsWorking Adults
B1Don’t Approve a Product Until You’ve Lived With It
Business EnglishWorking Adults
B1The Product Passed the Safety Test, But Was Still Too Hot to Hold
Business EnglishWorking Adults
B2The Product Worked, But the Packaging Made It Look Dead
Business EnglishWorking Adults
B2Why User Experience Is Harder Than Engineering
Business EnglishUniversity StudentsWorking Adults
C14 NPI Tips Before You Move Into Mass Production
Business EnglishWorking Adults
C1The Production Validation Test (PVT) Phase of the NPI Process
Business EnglishWorking Adults
C1The Three NPI Phases Explained
Business EnglishUniversity StudentsWorking Adults
C1When Can The NPI Process Begin?
Business EnglishUniversity StudentsWorking Adults
C1NPI Process #3: Why A Feasibility Study With Suppliers Saves Time & Prevents Issues
Business EnglishWorking Adults
C1NPI Process 2: New Product Development Process (Why Planning Before Prototyping Saves Time)
Business EnglishUniversity StudentsWorking Adults
C1PCBs | Electronic Goods Reliability Testing
Business EnglishUniversity StudentsWorking Adults
FOR YOU
Video consigliato
C12
150 frasi
15 IT Terms Everyone In Tech Recruitment Should Know – IT & Tech Recruitment Insights
Business EnglishWorking Adults
C11
4 frasi
Ambr®️ 250 High Throughput Perfusion Product Tutorial - Learn with Sartorius
Business EnglishUniversity StudentsWorking Adults
C1288 frasi
Using Selection & Scan Processing tools for reverse engineering | Geomagic Design X
Business EnglishWorking Adults
C12
306 frasi
Deep Dive: Investigating Thermal Cycling Failures Cracked MSOP Solder Joints
Business EnglishUniversity StudentsWorking Adults
C14
36 frasi
Overcoming Service Blueprinting Frustrations
Business EnglishWorking Adults
C13
50 frasi
✅ Coil Coating Process
Business EnglishUniversity StudentsWorking Adults
C11
443 frasi
Functional-Oriented Documentation in Automation - Eplan & IEC 81346 Explained
Business EnglishWorking Adults
C12
123 frasi
Order-to-Cash Process in SAP SD – Step by Step (Full Beginner Guide 2025)
Business EnglishUniversity StudentsWorking Adults
C13
115 frasi
Introduction 1, Context
Business EnglishUniversity StudentsWorking Adults
C13
131 frasi
Understanding BGA Pads: Solder Mask Defined vs Non-Defined
Business EnglishUniversity StudentsWorking Adults
Vocabolario e note di pronuncia per questa lezione
Questo video contiene 60 frasi e 742 parole da ripetere con lo shadowing. Il parlato dura 5:34. Chi parla mantiene un ritmo costante di circa 133 parole al minuto, comodo per lo shadowing. Solo il 78% delle parole rientra nelle 3.000 più comuni dell’inglese, quindi il lessico è impegnativo.
Vocaboli chiave di questo video
15 parole del video che vale la pena imparare, con pronuncia e significato:
| Parola | Pronuncia | Significato |
|---|---|---|
| flux sostantivo | /flʌks/ | flusso |
| residue sostantivo | /ˈɹɛzɪduː/ | residuo |
| thermal aggettivo | /ˈθɜːməl/ | termico |
| pasta sostantivo | /ˈpɑ.stə/ | pasta, impasto |
| particle sostantivo | /ˈpɑɹtək(ə)l/ | granello, pezzetto |
| trap sostantivo | /tɹæp/ | trappola, tranello |
| component sostantivo | /kəmˈpoʊ.nənt/ | componente |
| soak verbo | /soʊk/ | inzupparsi, imbeversi |
| vast aggettivo | /væst/ | ampio, vasto |
| element sostantivo | /ˈɛləmənt/ | elemento |
| solve verbo | /sɒlv/ | risolvere |
| define verbo | /dɪˈfaɪn/ | definire, determinare |
| symbol sostantivo | /ˈsɪmbəl/ | simbolo |
| slide sostantivo | /ˈslaɪ̯d/ | scivolo |
| reliable aggettivo | /ɹɪˈlaɪəbl̩/ | affidabile, sicuro |
I phrasal verb che sentirai
| Parola | Significato |
|---|---|
| check out verbo | investigare |
Pronuncia a cui fare attenzione
Chi parla usa 10 contrazioni e forme ridotte, come we're, don't, we'll. Pronunciale nella forma breve, così come le senti.
- I suoni “th”: thermal /ˈθɜːməl/, beneath /bɪˈniːθ/
- I suoni “sh” e “zh”: migration /maɪˈɡɹeɪʃ(ə)n/, oxidization /ˌɑksɪdɪˈzeɪʃ(ə)n/
- Parole lunghe — attenzione all’accento: momentum /ˌmə(ʊ)ˈmɛntəm/, humidity /hjuːˈmɪd.ə.ti/, parameter /pəˈɹæm.ə.tɚ/, assembler /əˈsɛmb(ə)lɚ/, electrically /ɪˈlɛk.tɹɪk.li/
Come esercitarsi con questo video
- Ascolta tutto il video una volta senza parlare e annota le parole che non conosci.
- Fai shadowing frase per frase a velocità normale, ripetendo ognuna finché il tuo ritmo coincide con quello di chi parla.
- Registrati e confronta con l’originale, facendo attenzione a parole come flux, residue, thermal.
Cos'è la tecnica dello Shadowing?
Shadowing è una tecnica di apprendimento delle lingue supportata da studi scientifici, originariamente sviluppata per la formazione dei traduttori professionisti e resa popolare dal poliglotta Dr. Alexander Arguelles. Il metodo è semplice ma potente: ascolti un audio in inglese di madrelingua e lo ripeti immediatamente ad alta voce — come un'ombra che segue il parlante con un ritardo di solo 1–2 secondi. A differenza dell'ascolto passivo o degli esercizi di grammatica, lo shadowing costringe il tuo cervello e i muscoli della bocca a elaborare e riprodurre simultaneamente i modelli di discorso reale. La ricerca dimostra che migliora significativamente la precisione della pronuncia, l'intonazione, il ritmo, il discorso connesso, la comprensione dell'ascolto e la fluidità del parlato — rendendolo uno dei metodi più efficaci per la preparazione alla prova di speaking dell'IELTS e per la comunicazione reale in inglese.